fix spelling in comments and strings

The tool comes from https://github.com/jsoref

Signed-off-by: Josh Soref <[email protected]>
Signed-off-by: Thomas Monjalon <[email protected]>

ethdev: add namespace

Add 'RTE_ETH' namespace to all enums & macros in a backward compatible
way. The macros for backward compatibility can be removed in next LTS.
Also updated some struct names to

ethdev: add namespace

Add 'RTE_ETH' namespace to all enums & macros in a backward compatible
way. The macros for backward compatibility can be removed in next LTS.
Also updated some struct names to have 'rte_eth' prefix.

All internal components switched to using new names.

Syntax fixed on lines that this patch touches.

Signed-off-by: Ferruh Yigit <[email protected]>
Acked-by: Tyler Retzlaff <[email protected]>
Acked-by: Andrew Rybchenko <[email protected]>
Acked-by: Ajit Khaparde <[email protected]>
Acked-by: Jerin Jacob <[email protected]>
Acked-by: Wisam Jaddo <[email protected]>
Acked-by: Rosen Xu <[email protected]>
Acked-by: Chenbo Xia <[email protected]>
Acked-by: Hemant Agrawal <[email protected]>
Acked-by: Somnath Kotur <[email protected]>

show more ...

ethdev: remove jumbo offload flag

Removing 'DEV_RX_OFFLOAD_JUMBO_FRAME' offload flag.

Instead of drivers announce this capability, application can deduct the
capability by checking reported 'dev_in

ethdev: remove jumbo offload flag

Removing 'DEV_RX_OFFLOAD_JUMBO_FRAME' offload flag.

Instead of drivers announce this capability, application can deduct the
capability by checking reported 'dev_info.max_mtu' or
'dev_info.max_rx_pktlen'.

And instead of application setting this flag explicitly to enable jumbo
frames, this can be deduced by driver by comparing requested 'mtu' to
'RTE_ETHER_MTU'.

Removing this additional configuration for simplification.

Suggested-by: Konstantin Ananyev <[email protected]>
Signed-off-by: Ferruh Yigit <[email protected]>
Acked-by: Andrew Rybchenko <[email protected]>
Reviewed-by: Rosen Xu <[email protected]>
Acked-by: Somnath Kotur <[email protected]>
Acked-by: Konstantin Ananyev <[email protected]>
Acked-by: Huisong Li <[email protected]>
Acked-by: Hyong Youb Kim <[email protected]>
Acked-by: Michal Krawczyk <[email protected]>

show more ...

ethdev: fix max Rx packet length

There is a confusion on setting max Rx packet length, this patch aims to
clarify it.

'rte_eth_dev_configure()' API accepts max Rx packet size via
'uint32_t max_rx_p

ethdev: fix max Rx packet length

There is a confusion on setting max Rx packet length, this patch aims to
clarify it.

'rte_eth_dev_configure()' API accepts max Rx packet size via
'uint32_t max_rx_pkt_len' field of the config struct 'struct
rte_eth_conf'.

Also 'rte_eth_dev_set_mtu()' API can be used to set the MTU, and result
stored into '(struct rte_eth_dev)->data->mtu'.

These two APIs are related but they work in a disconnected way, they
store the set values in different variables which makes hard to figure
out which one to use, also having two different method for a related
functionality is confusing for the users.

Other issues causing confusion is:
* maximum transmission unit (MTU) is payload of the Ethernet frame. And
'max_rx_pkt_len' is the size of the Ethernet frame. Difference is
Ethernet frame overhead, and this overhead may be different from
device to device based on what device supports, like VLAN and QinQ.
* 'max_rx_pkt_len' is only valid when application requested jumbo frame,
which adds additional confusion and some APIs and PMDs already
discards this documented behavior.
* For the jumbo frame enabled case, 'max_rx_pkt_len' is an mandatory
field, this adds configuration complexity for application.

As solution, both APIs gets MTU as parameter, and both saves the result
in same variable '(struct rte_eth_dev)->data->mtu'. For this
'max_rx_pkt_len' updated as 'mtu', and it is always valid independent
from jumbo frame.

For 'rte_eth_dev_configure()', 'dev->data->dev_conf.rxmode.mtu' is user
request and it should be used only within configure function and result
should be stored to '(struct rte_eth_dev)->data->mtu'. After that point
both application and PMD uses MTU from this variable.

When application doesn't provide an MTU during 'rte_eth_dev_configure()'
default 'RTE_ETHER_MTU' value is used.

Additional clarification done on scattered Rx configuration, in
relation to MTU and Rx buffer size.
MTU is used to configure the device for physical Rx/Tx size limitation,
Rx buffer is where to store Rx packets, many PMDs use mbuf data buffer
size as Rx buffer size.
PMDs compare MTU against Rx buffer size to decide enabling scattered Rx
or not. If scattered Rx is not supported by device, MTU bigger than Rx
buffer size should fail.

Signed-off-by: Ferruh Yigit <[email protected]>
Acked-by: Ajit Khaparde <[email protected]>
Acked-by: Somnath Kotur <[email protected]>
Acked-by: Huisong Li <[email protected]>
Acked-by: Andrew Rybchenko <[email protected]>
Acked-by: Konstantin Ananyev <[email protected]>
Acked-by: Rosen Xu <[email protected]>
Acked-by: Hyong Youb Kim <[email protected]>

show more ...

examples: remove unneeded atomic header include

Remove the unnecessary header file rte_atomic.h
included in example module.

Signed-off-by: Joyce Kong <[email protected]>
Signed-off-by: Dharmik Tha

examples: remove unneeded atomic header include

Remove the unnecessary header file rte_atomic.h
included in example module.

Signed-off-by: Joyce Kong <[email protected]>
Signed-off-by: Dharmik Thakkar <[email protected]>
Reviewed-by: Ruifeng Wang <[email protected]>

show more ...

net: rename Ethernet header fields

Definition of `rte_ether_addr` structure used a workaround allowing DPDK
and Windows SDK headers to be used in the same file, because Windows SDK
defines `s_addr`

net: rename Ethernet header fields

Definition of `rte_ether_addr` structure used a workaround allowing DPDK
and Windows SDK headers to be used in the same file, because Windows SDK
defines `s_addr` as a macro. Rename `s_addr` to `src_addr` and `d_addr`
to `dst_addr` to avoid the conflict and remove the workaround.
Deprecation notice:
https://mails.dpdk.org/archives/dev/2021-July/215270.html

Signed-off-by: Dmitry Kozlyuk <[email protected]>

show more ...