arm64: dts: allwinner: h700: Add Anbernic RG35XX-SP

The Anbernic RG35XXSP is almost identical to the RG35XX-Plus, but in a
clamshell form-factor. The key differences between the SP and the Plus
is a

arm64: dts: allwinner: h700: Add Anbernic RG35XX-SP

The Anbernic RG35XXSP is almost identical to the RG35XX-Plus, but in a
clamshell form-factor. The key differences between the SP and the Plus
is a lid switch and an RTC on the same i2c bus as the PMIC.

Signed-off-by: Chris Morgan <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Chen-Yu Tsai <[email protected]>

show more ...

arm64: dts: allwinner: h700: Add RG35XX-H DTS

The RG35XX-H adds thumbsticks, a stereo speaker, and a second USB port to
the RG35XX-Plus, and has a horizontal form factor.

Enabled in this DTS:
- Thu

arm64: dts: allwinner: h700: Add RG35XX-H DTS

The RG35XX-H adds thumbsticks, a stereo speaker, and a second USB port to
the RG35XX-Plus, and has a horizontal form factor.

Enabled in this DTS:
- Thumbsticks
- Second USB port

Signed-off-by: Ryan Walklin <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Reviewed-by: Jernej Skrabec <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jernej Skrabec <[email protected]>

show more ...

arm64: dts: allwinner: h700: Add RG35XX-Plus DTS

The RG35XX-Plus adds a RTL8221CS SDIO Wifi/BT chip to the RG35XX (2024).

Enabled in this DTS:
- WiFi
- Bluetooth
- Supporting power sequence and GPI

arm64: dts: allwinner: h700: Add RG35XX-Plus DTS

The RG35XX-Plus adds a RTL8221CS SDIO Wifi/BT chip to the RG35XX (2024).

Enabled in this DTS:
- WiFi
- Bluetooth
- Supporting power sequence and GPIOs

Signed-off-by: Ryan Walklin <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Reviewed-by: Jernej Skrabec <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jernej Skrabec <[email protected]>

show more ...

arm64: dts: allwinner: h700: Add RG35XX 2024 DTS

The base model RG35XX (2024) is a handheld gaming device based on an
Allwinner H700 chip.

The H700 is a H616 variant (4x ARM Cortex-A53 cores @ 1.5G

arm64: dts: allwinner: h700: Add RG35XX 2024 DTS

The base model RG35XX (2024) is a handheld gaming device based on an
Allwinner H700 chip.

The H700 is a H616 variant (4x ARM Cortex-A53 cores @ 1.5Ghz with Mali G31
GPU) which exposes RGB LCD and NMI pins.

Device features:
- Allwinner H700 @ 1.5GHz
- 1GB LPDDR4 DRAM
- X-Powers AXP717 PMIC
- 3.5" 640x480 RGB LCD
- Two microSD slots
- Mini-HDMI out
- GPIO keypad
- 3.5mm headphone jack
- USB-C charging port

Enabled in this DTS:
- AXP717 PMIC with RSB serial interface, regulators and NMI interrupt
controller
- Power LED (charge LED on device controlled directly by PMIC)
- Serial UART (accessible from headers on the board)
- First SD slot (SD2 appears to have a GPIO-switched regulator for 1.8v
low-voltage signalling, this is not yet modeled. Enablement with a
switched regulator will be confirmed and posted in a follow-up patch).

Signed-off-by: Ryan Walklin <[email protected]>
Reviewed-by: Jernej Skrabec <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jernej Skrabec <[email protected]>

show more ...

arm64: dts: allwinner: Add Tanix TX1 support

The Tanix TX1 is a tiny TV box with the Allwinner H313 SoC. The box
features no Ethernet or an SD card slot, which makes booting from it
somewhat interes

arm64: dts: allwinner: Add Tanix TX1 support

The Tanix TX1 is a tiny TV box with the Allwinner H313 SoC. The box
features no Ethernet or an SD card slot, which makes booting from it
somewhat interesting: Pressing the hidden FEL button and using a USB-A
to USB-A cable to upload code from a host PC is one way to run mainline.
The box features:
- Allwinner H313 SoC (4 * Arm Cortex-A53 cores)
- 1 or 2 GB DRAM
- 8 or 16 GB eMMC flash
- SCI S9082H WiFi chip
- HDMI port
- one USB 2.0 port
- 3.5mm AV port
- barrel plug 5V DC input via barrel plug

The devicetree covers most peripherals.
The eMMC did not work properly in HS200 speed mode, so this mode property
is omitted. HS-DDR seems to work fine.
The blue LED is connected to the same GPIO pin as the red LED, just
using the opposite polarity. Apparently there is no way of describing
this in DT, so the red LED is omitted.
Next to the FEL button is a hidden button, that can be pushed by using
something like a paperclip, through the ventilation vents of the case.

Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Jernej Skrabec <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jernej Skrabec <[email protected]>

show more ...

arm64: dts: allwinner: h616: Add Sipeed Longan SoM 3H and Pi 3H board support

The Sipeed Longan SoM 3H is a system on module based on the Allwinner
H618 SoC. The SoM features:

- Four ARM Cortex-A53

arm64: dts: allwinner: h616: Add Sipeed Longan SoM 3H and Pi 3H board support

The Sipeed Longan SoM 3H is a system on module based on the Allwinner
H618 SoC. The SoM features:

- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 2/4 GiB LPDDR4 DRAM SoMs
- AXP313a PMIC
- eMMC

The Sipeed Longan PI 3H is a development board based on the above SoM.
The board features:
- Longan SoM 3H
- Raspberry-Pi-1 compatible GPIO header
- 2 USB 2.0 host port
- 1 USB 2.0 type C port (power supply + OTG)
- MicroSD slot
- 1Gbps Ethernet port (via RTL8211 PHY)
- HDMI port
- WiFi/BT chip

Add the devicetree file describing the currently supported features,
namely PMIC, LEDs, UART, SD card, eMMC, USB and Ethernet.

Signed-off-by: Jisheng Zhang <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Reviewed-by: Jernej Skrabec <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jernej Skrabec <[email protected]>

show more ...

arm64: dts: allwinner: Add Jide Remix Mini PC support

The Remix Mini PC is a "mini computer" using the Allwinner H64 SoC,
which appears to be just a relabelled A64. It was launched in 2015 by
the no

arm64: dts: allwinner: Add Jide Remix Mini PC support

The Remix Mini PC is a "mini computer" using the Allwinner H64 SoC,
which appears to be just a relabelled A64. It was launched in 2015 by
the now defunct company Jide, and shipped with a desktop optimised
version of Android. It features
- Allwinner H64 Soc (4 * Arm Cortex-A53 cores)
- 1 or 2 GB DRAM
- 8 or 16 GB eMMC flash
- 100 MBit Ethernet port (using an X-Powers AC200 PHY)
- RTL8723BS WiFi & Bluetooth chip
- HDMI port
- two USB 2.0 ports
- 3.5mm AV port
- microSD card slot

The devicetree covers most peripherals, though there is no agreed
binding for the PHY chip yet, so this is left out.
The eMMC did not work with the MMC DDR speed mode, so this mode property
is omitted.

Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Jernej Skrabec <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jernej Skrabec <[email protected]>

show more ...

arm64: dts: allwinner: h616: Add Orange Pi Zero 2W to Makefile

Orange Pi Zero 2W dts file is not included in Makefile. Fix this.

Fixes: c505ee1eae18 ("arm64: dts: allwinner: h616: add Orange Pi Zer

arm64: dts: allwinner: h616: Add Orange Pi Zero 2W to Makefile

Orange Pi Zero 2W dts file is not included in Makefile. Fix this.

Fixes: c505ee1eae18 ("arm64: dts: allwinner: h616: add Orange Pi Zero 2W support")
Reviewed-by: Andre Przywara <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jernej Skrabec <[email protected]>

show more ...

arm64: dts: allwinner: h618: add Transpeed 8K618-T TV box

This is a Chinese TV box, probably very similar if not identical to
various other cheap TV boxes with the same specs:
- Allwinner H618

arm64: dts: allwinner: h618: add Transpeed 8K618-T TV box

This is a Chinese TV box, probably very similar if not identical to
various other cheap TV boxes with the same specs:
- Allwinner H618 SoC (4 * Arm Cortex-A53 cores, 1MB L2 cache)
- 2 or 4GiB DDR3L DRAM
- 32, 64, or 128 GiB eMMC flash
- AXP313a PMIC
- 100 Mbit/s Ethernet (using yet unsupported internal PHY)
- HDMI port
- 2 * USB 2.0 ports
- microSD card slot
- 3.5mm A/V port
- 7-segment display
- 5V barrel plug power supply

The PCB provides holes for soldering a UART header or cable, this is
connected to the debug UART0. UART1 is used for the Bluetooth chip,
although this isn't working yet.

Signed-off-by: Andre Przywara <[email protected]>
Acked-by: Jernej Skrabec <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jernej Skrabec <[email protected]>

show more ...

arm64: dts: allwinner: h616: Add BigTreeTech Pi support

The BigTreeTech Pi is an H616 based board based on CB1.
Just in Rpi format board.

It features the same internals as BTT CB1 but adds:
- F

arm64: dts: allwinner: h616: Add BigTreeTech Pi support

The BigTreeTech Pi is an H616 based board based on CB1.
Just in Rpi format board.

It features the same internals as BTT CB1 but adds:
- Fan port
- IR receiver
- ADXL345 Accelerometer connector via SPI
- 24V DC power supply via terminal plugs
- USB to CAN module connector (External Module)

List of currently working things is same as BTT CB1 but also:
- IR receiver
- ADXL345 connector

Signed-off-by: Martin Botka <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Acked-by: Jernej Skrabec <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jernej Skrabec <[email protected]>

show more ...

arm64: dts: allwinner: h616: Add BigTreeTech CB1 SoM & boards support

CB1 is Compute Module style board that plugs into Rpi board style adapter or
Manta 3D printer boards (M4P/M8P).

The SoM feature

arm64: dts: allwinner: h616: Add BigTreeTech CB1 SoM & boards support

CB1 is Compute Module style board that plugs into Rpi board style adapter or
Manta 3D printer boards (M4P/M8P).

The SoM features:
- H616 SoC
- 1GiB of RAM
- AXP313A PMIC
- RTL8189FTV WiFi

Boards feature:
- 4x USB via USB2 hub (usb1 on SoM).
- SDcard slot for loading images.
- Ethernet port wired to the internal PHY. (100M)
- 2x HDMI 2.0. (Only 1 usable on CB1)
- Power and Status LEDs. (Only Status LED usable on CB1)
- 40 pin GPIO header

Currently working:
- Booting
- USB
- UART
- MMC
- Status LED
- WiFi (RTL8189FS via out of tree driver)

I didnt want to duplicate things so the manta DTS can also be used on BTT pi4b adapter.
CB1 SoM has its own DTSI file in case other boards shows up that accept this SoM.

Signed-off-by: Martin Botka <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Reviewed-by: Jernej Skrabec <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jernej Skrabec <[email protected]>

show more ...

arm64: dts: allwinner: h616: Add OrangePi Zero 3 board support

The OrangePi Zero 3 is a development board based on the Allwinner H618 SoC,
which seems to be just an H616 with more L2 cache. The boar

arm64: dts: allwinner: h616: Add OrangePi Zero 3 board support

The OrangePi Zero 3 is a development board based on the Allwinner H618 SoC,
which seems to be just an H616 with more L2 cache. The board itself is a
slightly updated version of the Orange Pi Zero 2. It features:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 1/1.5/2/4 GiB LPDDR4 DRAM SKUs (only up to 1GB on the Zero2)
- AXP313a PMIC (more capable AXP305 on the Zero2)
- Raspberry-Pi-1 compatible GPIO header
- extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports
- 1 USB 2.0 host port
- 1 USB 2.0 type C port (power supply + OTG)
- MicroSD slot
- on-board 16MiB bootable SPI NOR flash (only 2MB on the Zero2)
- 1Gbps Ethernet port (via Motorcomm YT8531 PHY) (RTL8211 on the Zero2)
- micro-HDMI port
- (yet) unsupported Allwinner WiFi/BT chip

Add the devicetree file describing the currently supported features,
namely LEDs, SD card, PMIC, SPI flash, USB. Ethernet seems unstable at
the moment, though the basic functionality works.

Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Jernej Skrabec <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jernej Skrabec <[email protected]>

show more ...

arm64: dts: allwinner: h616: Add X96 Mate TV box support

The X96 Mate is an Allwinner H616 based TV box, featuring:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 2GiB/4GiB RAM (fully usable!)

arm64: dts: allwinner: h616: Add X96 Mate TV box support

The X96 Mate is an Allwinner H616 based TV box, featuring:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 2GiB/4GiB RAM (fully usable!)
- 16/32/64GiB eMMC
- 100Mbps Ethernet (via embedded AC200 EPHY, not yet supported)
- Unsupported Allwinner WiFi chip
- 2 x USB 2.0 host ports
- HDMI port
- IR receiver
- 5V/2A DC power supply via barrel plug

Add a basic devicetree for it, with SD card and eMMC working, as
well as serial and the essential peripherals, like the AXP PMIC.

This DT is somewhat minimal, and should work on many other similar TV
boxes with the Allwinner H616 chip.

Signed-off-by: Andre Przywara <[email protected]>
Reviewed-by: Samuel Holland <[email protected]>
Signed-off-by: Jernej Skrabec <[email protected]>
Link: https://lore.kernel.org/r/[email protected]

show more ...

arm64: dts: allwinner: h616: Add OrangePi Zero 2 board support

The OrangePi Zero 2 is a development board with the new H616 SoC. It
comes with the following features:
- Four ARM Cortex-A53 cores,

arm64: dts: allwinner: h616: Add OrangePi Zero 2 board support

The OrangePi Zero 2 is a development board with the new H616 SoC. It
comes with the following features:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 512MiB/1GiB DDR3 DRAM
- AXP305 PMIC
- Raspberry-Pi-1 compatible GPIO header
- extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports
- 1 USB 2.0 host port
- 1 USB 2.0 type C port (power supply + OTG)
- MicroSD slot
- on-board 2MiB bootable SPI NOR flash
- 1Gbps Ethernet port (via RTL8211F PHY)
- micro-HDMI port
- (yet) unsupported Allwinner WiFi/BT chip

Add the devicetree file describing the currently supported features.

Signed-off-by: Andre Przywara <[email protected]>
Acked-by: Samuel Holland <[email protected]>
Signed-off-by: Jernej Skrabec <[email protected]>
Link: https://lore.kernel.org/r/[email protected]

show more ...

arm64: dts: allwinner: h6: Add Tanix TX6 mini dts

Tanix TX6 mini is less capable version of Tanix TX6 although it comes
with some features not present on Tanix TX6.

Basic specs:
- H6 SoC
- 2 GiB DD

arm64: dts: allwinner: h6: Add Tanix TX6 mini dts

Tanix TX6 mini is less capable version of Tanix TX6 although it comes
with some features not present on Tanix TX6.

Basic specs:
- H6 SoC
- 2 GiB DDR3 RAM
- HDMI
- SPDIF
- 2x USB
- analogue audio
- CVBS
- SD card
- IR remote
- LED display
- fast ethernet
- XR819 wifi
- 16 GiB eMMC

Currently supported features doesn't differ that much from Tanix TX6,
but that will change soon.

Signed-off-by: Jernej Skrabec <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>

show more ...

arm64: dts: allwinner: h5: Add NanoPi R1S H5 support

The NanoPi R1S H5 is a open source board made by FriendlyElec.
It has the following features:

- Allwinner H5, Quad-core Cortex-A53
- 512MB DDR3

arm64: dts: allwinner: h5: Add NanoPi R1S H5 support

The NanoPi R1S H5 is a open source board made by FriendlyElec.
It has the following features:

- Allwinner H5, Quad-core Cortex-A53
- 512MB DDR3 RAM
- 10/100/1000M Ethernet x 2
- RTL8189ETV WiFi 802.11b/g/n
- USB 2.0 host port (A)
- MicroSD Slot
- Serial Debug Port
- 5V 2A DC power-supply

Signed-off-by: Chukun Pan <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]

show more ...

arm64: allwinner: dts: a64: add DT for Early Adopter's PineTab

PineTabs since Early Adopter batch will use a new LCD panel.

Add device tree for PineTab with the new panel.

Signed-off-by: Icenowy Z

arm64: allwinner: dts: a64: add DT for Early Adopter's PineTab

PineTabs since Early Adopter batch will use a new LCD panel.

Add device tree for PineTab with the new panel.

Signed-off-by: Icenowy Zheng <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/[email protected]

show more ...

arm64: allwinner: A100: add support for Allwinner Perf1 board

A100 perf1 is an Allwinner A100-based SBC, with the following features:

- 1GiB DDR3 DRAM
- AXP803 PMIC
- 2 USB 2.0 ports
- MicroSD slot

arm64: allwinner: A100: add support for Allwinner Perf1 board

A100 perf1 is an Allwinner A100-based SBC, with the following features:

- 1GiB DDR3 DRAM
- AXP803 PMIC
- 2 USB 2.0 ports
- MicroSD slot and on-board eMMC module
- on-board Nand flash
- ···

Adds initial support for it, including UART and PMU.

Signed-off-by: Yangtao Li <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>
Link: https://lore.kernel.org/r/30f4a3fc6ac84d05094e2c3b89d1dddc8ff6b7fc.1595572867.git.frank@allwinnertech.com

show more ...

arm64: dts: allwinner: Add support for PinePhone revision 1.2

Revision 1.2 should be the final production version of the PinePhone.
It has most of the known HW quirks fixed.

Interrupt to the magnet

arm64: dts: allwinner: Add support for PinePhone revision 1.2

Revision 1.2 should be the final production version of the PinePhone.
It has most of the known HW quirks fixed.

Interrupt to the magnetometer is routed correctly, in this revision.

The bulk of the changes are in how modem and the USB-C HDMI bridge
chip is powered and where the signals from the modem are connected.

Also backlight intensity seemingly behaves differently, than on the
1.1 and 1.0 boards, and the PWM duty cycle where backlight starts
to work is 10% (as tested on 2 1.2 PinePhones I have access to).

Signed-off-by: Ondrej Jirman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Maxime Ripard <[email protected]>

show more ...

arm64: dts: allwinner: Add initial support for Pine64 PinePhone

At the moment PinePhone comes in two slightly incompatible variants:

- 1.0: Early Developer Batch
- 1.1: Braveheart Batch

There will

arm64: dts: allwinner: Add initial support for Pine64 PinePhone

At the moment PinePhone comes in two slightly incompatible variants:

- 1.0: Early Developer Batch
- 1.1: Braveheart Batch

There will be at least one more incompatible variant in the very near
future, so let's start by sharing the dtsi among multiple variants,
right away, even though the HW description doesn't yet include the
different bits.

The differences between 1.0 and 1.1 are: change in pins that control
the flash LED, differences in modem power status signal routing, and
maybe some other subtler things, that have not been determined yet.

This is a basic DT that includes only features that are already
supported by mainline drivers.

Co-developed-by: Samuel Holland <[email protected]>
Signed-off-by: Samuel Holland <[email protected]>
Co-developed-by: Martijn Braam <[email protected]>
Signed-off-by: Martijn Braam <[email protected]>
Co-developed-by: Luca Weiss <[email protected]>
Signed-off-by: Luca Weiss <[email protected]>
Signed-off-by: Bhushan Shah <[email protected]>
Signed-off-by: Icenowy Zheng <[email protected]>
Signed-off-by: Ondrej Jirman <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>

show more ...

arm64: dts: allwinner: a64: add support for PineTab

PineTab is a 10.1" tablet by Pine64 with Allwinner A64 inside.

It includes the following peripherals:

USB:
- A microUSB Type-B port connected to

arm64: dts: allwinner: a64: add support for PineTab

PineTab is a 10.1" tablet by Pine64 with Allwinner A64 inside.

It includes the following peripherals:

USB:
- A microUSB Type-B port connected to the OTG-capable USB PHY of
Allwinner A64. The ID pin is connected to a GPIO of the A64 SoC, and the
Vbus is connected to the Vbus of AXP803 PMIC. These enables OTG
functionality on this port.
- A USB Type-A port is connected to the internal hub attached to the
non-OTG USB PHY of Allwinner A64.
- There are reserved pins for an external keyboard connected to the
internal hub.

Power:
- The microUSB port has its Vbus connected to AXP803, mentioned above.
- A DC jack (of a strange size, 2.5mm outer diameter) is connected to
the ACIN of AXP803.
- A Li-Polymer battery is connected to the battery pins of AXP803.

Storage:
- An tradition Pine64 eMMC slot is on the board, mounted with an eMMC
module by factory.
- An external microSD slot is hidden under a protect case.

Display:
- A MIPI-DSI LCD panel (800x1280) is connected to the DSI port of A64 SoC.
- A mini HDMI port.

Input:
- A touch panel attached to a Goodix GT9271 touch controller.
- Volume keys connected to the LRADC of the A64 SoC.

Camera:
- An OV5640 CMOS camera is at rear, connected to the CSI bus of A64 SoC.
- A GC2145 CMOS camera is at front, shares the same CSI bus with OV5640.

Audio:
- A headphone jack is conencted to the SoC's internal codec.
- A speaker connected is to the Line Out port of SoC's internal codec, via
an amplifier.

Misc:
- Debug UART is muxed with the headphone jack, with the switch next to
the microSD slot.
- A bosch BMA223 accelerometer is connected to the I2C bus of A64 SoC.
- Wi-Fi and Bluetooth are available via a RTL8723CS chip, similar to the
one in Pinebook.

This commit adds a basically usable device tree for it, implementing
most of the features mentioned above. HDMI is not supported now because
bad LCD-HDMI coexistence situation of mainline A64 display driver, the
front camera currently lacks a driver and a facility to share the bus
with the rear one, and the accelerometer currently lacks a DT binding.

Signed-off-by: Icenowy Zheng <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>

show more ...

arm64: dts: allwinner: h5: Add Libre Computer ALL-H5-CC H5 board

The Libre Computer ALL-H5-CC board is an upgraded version of the
ALL-H3-CC. Changes include:

- Gigabit Ethernet via external RTL82

arm64: dts: allwinner: h5: Add Libre Computer ALL-H5-CC H5 board

The Libre Computer ALL-H5-CC board is an upgraded version of the
ALL-H3-CC. Changes include:

- Gigabit Ethernet via external RTL8211E Ethernet PHY
- 16 MiB SPI NOR flash memory
- PoE tap header
- Line out jack removed

Only H5 variant test samples were made available, and the vendor is not
certain whether other SoC variants would be made or not. Furthermore the
board is a minor upgrade compared to the ALL-H3-CC. Thus the device tree
simply includes the one for the ALL-H3-CC, and adds the changes on top.

Signed-off-by: Chen-Yu Tsai <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>

show more ...

ARM: dts: sunxi: Add Libre Computer ALL-H3-IT H5 board

The Libre Computer ALL-H3-IT board is a small single board computer that
is roughly the same size as the Raspberry Pi Zero, or around 20% small

ARM: dts: sunxi: Add Libre Computer ALL-H3-IT H5 board

The Libre Computer ALL-H3-IT board is a small single board computer that
is roughly the same size as the Raspberry Pi Zero, or around 20% smaller
than a credit card.

The board features:

- H2, H3, or H5 SoC from Allwinner
- 2 DDR3 DRAM chips
- Realtek RTL8821CU based WiFi module
- 128 Mbit SPI-NOR flash
- micro-SD card slot
- micro HDMI video output
- FPC connector for camera sensor module
- generic Raspberri-Pi style 40 pin GPIO header
- additional pin headers for extra USB host ports, ananlog audio and
IR receiver

Only H5 variant test samples were made available, but the vendor does
have plans to include at least an H3 variant. Thus the device tree is
split much like the ALL-H3-CC, with a common dtsi file for the board
design, and separate dts files including the common board file and the
SoC dtsi file. The other variants will be added as they are made
available.

Signed-off-by: Chen-Yu Tsai <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>

show more ...

arm64: dts: allwinner: add pineh64 model B

This patch adds the model B of the PineH64.
The model B is smaller than the pine64 model A and has no PCIE slot.

The only devicetree difference with the p

arm64: dts: allwinner: add pineh64 model B

This patch adds the model B of the PineH64.
The model B is smaller than the pine64 model A and has no PCIE slot.

The only devicetree difference with the pineH64 model A, is the PHY
regulator and the HDMI connector node.

Signed-off-by: Corentin Labbe <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>

show more ...

arm64: dts: allwinner: a64: Add A64 OlinuXino board (with eMMC)

A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2G

arm64: dts: allwinner: a64: Add A64 OlinuXino board (with eMMC)

A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In
addition, there are two variants without eMMC. One without eMMC and one with SPI
flash. This suggests the need for separate device tree for the three eMMC
variants.

This patch has been tested on A64-OLinuXino-1Ge16GW with Linux 5.0 from Debain.
Basic benchmarks using Flexible IO Tester show reasonable performance from the
eMMC.

eMMC - Random Write: 21.3MiB/s
eMMC - Sequential Write: 68.2MiB/s
SD Card - Random Write: 1690KiB/s
SD Card - Sequential Write: 11.0MiB/s

Changes:

v3: Separate dts for eMMC variants

v2: Fix descriptions for VCC and VCCQ

Link: https://github.com/armbian/build/commit/174953de1eb09e6aa1ef7075066b573dba625398
Signed-off-by: Martin Ayotte <[email protected]>
[[email protected] Fix descriptions for VCC and VCCQ, separate dts for eMMC]
Signed-off-by: Sunil Mohan Adapa <[email protected]>
Tested-by: Sunil Mohan Adapa <[email protected]>
Signed-off-by: Maxime Ripard <[email protected]>

show more ...