firmware: broadcom: add OP-TEE based BNXT f/w manager

This driver registers on TEE bus to interact with OP-TEE based
BNXT firmware management modules

Cc: Jakub Kicinski <[email protected]

firmware: broadcom: add OP-TEE based BNXT f/w manager

This driver registers on TEE bus to interact with OP-TEE based
BNXT firmware management modules

Cc: Jakub Kicinski <[email protected]>
Reported-by: kbuild test robot <[email protected]>
Signed-off-by: Vikas Gupta <[email protected]>
Signed-off-by: Sheetal Tigadoli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

treewide: Add SPDX license identifier - Makefile/Kconfig

Add SPDX license identifiers to all Make/Kconfig files which:

- Have no license information of any form

These files fall under the project

treewide: Add SPDX license identifier - Makefile/Kconfig

Add SPDX license identifiers to all Make/Kconfig files which:

- Have no license information of any form

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

GPL-2.0-only

Signed-off-by: Thomas Gleixner <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

MIPS: BCM47xx: Move SPROM driver to drivers/firmware/

Broadcom ARM home routers store SPROM content in NVRAM just like MIPS
ones. To share SPROM code we need to move it out of arch/mips/ to some
com

MIPS: BCM47xx: Move SPROM driver to drivers/firmware/

Broadcom ARM home routers store SPROM content in NVRAM just like MIPS
ones. To share SPROM code we need to move it out of arch/mips/ to some
common place. We already have bcm47xx_nvram in firmware path and SPROM
should fit there as well.
This driver is responsible for parsing SoC configuration data into a
struct shared between ssb and bcma buses.
This was tested with BCM4706 & BCM5357C0 (BCM47XX) and BCM4708A0
(ARCH_BCM_5301X).

Signed-off-by: Rafał Miłecki <[email protected]>
Cc: Hauke Mehrtens <[email protected]>
Cc: [email protected]
Patchwork: https://patchwork.linux-mips.org/patch/12210/
Signed-off-by: Ralf Baechle <[email protected]>

show more ...

MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/

After Broadcom switched from MIPS to ARM for their home routers we need
to have NVRAM driver in some common place (not arch/mips/). As expla

MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/

After Broadcom switched from MIPS to ARM for their home routers we need
to have NVRAM driver in some common place (not arch/mips/). As explained
in Kconfig, this driver is responsible for parsing SoC configuration
data that is passed to the kernel in flash from the bootloader firmware
called "CFE".

We were thinking about putting it in bus directory, however there are
two possible buses for MIPS: drivers/ssb/ and drivers/bcma/. So this
won't fit there and this is why I would like to move this driver to the
drivers/firmware/.

Signed-off-by: Rafał Miłecki <[email protected]>
Reviewed-by: Paul Walmsley <[email protected]>
Cc: [email protected]
Cc: Hauke Mehrtens <[email protected]>
Cc: Seiji Aguchi <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: Ard Biesheuvel <[email protected]>
Cc: Mike Waychison <[email protected]>
Cc: Roy Franz <[email protected]>
Cc: Matt Fleming <[email protected]>
Cc: Linus Torvalds <[email protected]>
Patchwork: https://patchwork.linux-mips.org/patch/10544/
Signed-off-by: Ralf Baechle <[email protected]>

show more ...