Changes in Makefile

24688095 - firmware: broadcom: add OP-TEE based BNXT f/w manager

Thu, 31 Oct 2019 10:08:50 +0000

firmware: broadcom: add OP-TEE based BNXT f/w managerThis driver registers on TEE bus to interact with OP-TEE basedBNXT firmware management modulesCc: Jakub Kicinski Reported-by: kbuild test robot Signed-off-by: Vikas Gupta Signed-off-by: Sheetal Tigadoli Signed-off-by: David S. Miller List of files: /linux-6.15/drivers/firmware/broadcom/Makefile

ec8f24b7 - treewide: Add SPDX license identifier - Makefile/Kconfig

Sun, 19 May 2019 12:07:45 +0000

treewide: Add SPDX license identifier - Makefile/KconfigAdd SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any formThese files fall under the project license, GPL v2 only. The resulting SPDXlicense identifier is: GPL-2.0-onlySigned-off-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman List of files: /linux-6.15/drivers/firmware/broadcom/Makefile

2ab71a02 - MIPS: BCM47xx: Move SPROM driver to drivers/firmware/

Mon, 25 Jan 2016 08:50:29 +0000

MIPS: BCM47xx: Move SPROM driver to drivers/firmware/Broadcom ARM home routers store SPROM content in NVRAM just like MIPSones. To share SPROM code we need to move it out of arch/mips/ to somecommon place. We already have bcm47xx_nvram in firmware path and SPROMshould fit there as well.This driver is responsible for parsing SoC configuration data into astruct shared between ssb and bcma buses.This was tested with BCM4706 & BCM5357C0 (BCM47XX) and BCM4708A0(ARCH_BCM_5301X).Signed-off-by: Rafał Miłecki Cc: Hauke Mehrtens Cc: linux-mips@linux-mips.orgPatchwork: https://patchwork.linux-mips.org/patch/12210/Signed-off-by: Ralf Baechle List of files: /linux-6.15/drivers/firmware/broadcom/Makefile

f6e734a8 - MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/

Wed, 10 Jun 2015 21:05:08 +0000

MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/After Broadcom switched from MIPS to ARM for their home routers we needto have NVRAM driver in some common place (not arch/mips/). As explainedin Kconfig, this driver is responsible for parsing SoC configurationdata that is passed to the kernel in flash from the bootloader firmwarecalled "CFE".We were thinking about putting it in bus directory, however there aretwo possible buses for MIPS: drivers/ssb/ and drivers/bcma/. So thiswon't fit there and this is why I would like to move this driver to thedrivers/firmware/.Signed-off-by: Rafał Miłecki Reviewed-by: Paul Walmsley Cc: linux-mips@linux-mips.orgCc: Hauke Mehrtens Cc: Seiji Aguchi Cc: Greg Kroah-Hartman Cc: Ard Biesheuvel Cc: Mike Waychison Cc: Roy Franz Cc: Matt Fleming Cc: Linus Torvalds Patchwork: https://patchwork.linux-mips.org/patch/10544/Signed-off-by: Ralf Baechle List of files: /linux-6.15/drivers/firmware/broadcom/Makefile