Decouple `serde` from its `derive` crate (#6917)

By not activating the `derive` feature on `serde`, the compilation speed
can be improved by a lot. This is because `serde` can then compile in
parall

Decouple `serde` from its `derive` crate (#6917)

By not activating the `derive` feature on `serde`, the compilation speed
can be improved by a lot. This is because `serde` can then compile in
parallel to `serde_derive`, allowing it to finish compilation possibly
even before `serde_derive`, unblocking all the crates waiting for
`serde` to start compiling much sooner.

As it turns out the main deciding factor for how long the compile time of a
project is, is primarly determined by the depth of dependencies rather
than the width. In other words, a crate's compile times aren't affected
by how many crates it depends on, but rather by the longest chain of
dependencies that it needs to wait on. In many cases `serde` is part of
that long chain, as it is part of a long chain if the `derive` feature
is active:

`proc-macro2` compile build script > `proc-macro2` run build script >
`proc-macro2` > `quote` > `syn` > `serde_derive` > `serde` >
`serde_json` (or any crate that depends on serde)

By decoupling it from `serde_derive`, the chain is shortened and compile
times get much better.

Check this issue for a deeper elaboration:
https://github.com/serde-rs/serde/issues/2584

For `wasmtime` I'm seeing a reduction from 24.75s to 22.45s when
compiling in `release` mode. This is because wasmtime through `gimli`
has a dependency on `indexmap` which can only start compiling when
`serde` is finished, which you want to happen as early as possible so
some of wasmtime's dependencies can start compiling.

To measure the full effect, the dependencies can't by themselves
activate the `derive` feature. I've upstreamed a patch for
`fxprof-processed-profile` which was the only dependency that activated
it for `wasmtime` (not yet published to crates.io). `wasmtime-cli` and
co. may need patches for their dependencies to see a similar
improvement.

show more ...

fuzzgen: Add `AtomicRMW` (#5861)

More atomic ops

Implement Wasm Atomics for Cranelift/newBE/aarch64.

The implementation is pretty straightforward. Wasm atomic instructions fall
into 5 groups

* atomic read-modify-write
* atomic compare-and-swap
*

Implement Wasm Atomics for Cranelift/newBE/aarch64.

The implementation is pretty straightforward. Wasm atomic instructions fall
into 5 groups

* atomic read-modify-write
* atomic compare-and-swap
* atomic loads
* atomic stores
* fences

and the implementation mirrors that structure, at both the CLIF and AArch64
levels.

At the CLIF level, there are five new instructions, one for each group. Some
comments about these:

* for those that take addresses (all except fences), the address is contained
entirely in a single `Value`; there is no offset field as there is with
normal loads and stores. Wasm atomics require alignment checks, and
removing the offset makes implementation of those checks a bit simpler.

* atomic loads and stores get their own instructions, rather than reusing the
existing load and store instructions, for two reasons:

- per above comment, makes alignment checking simpler

- reuse of existing loads and stores would require extension of `MemFlags`
to indicate atomicity, which sounds semantically unclean. For example,
then *any* instruction carrying `MemFlags` could be marked as atomic, even
in cases where it is meaningless or ambiguous.

* I tried to specify, in comments, the behaviour of these instructions as
tightly as I could. Unfortunately there is no way (per my limited CLIF
knowledge) to enforce the constraint that they may only be used on I8, I16,
I32 and I64 types, and in particular not on floating point or vector types.

The translation from Wasm to CLIF, in `code_translator.rs` is unremarkable.

At the AArch64 level, there are also five new instructions, one for each
group. All of them except `::Fence` contain multiple real machine
instructions. Atomic r-m-w and atomic c-a-s are emitted as the usual
load-linked store-conditional loops, guarded at both ends by memory fences.
Atomic loads and stores are emitted as a load preceded by a fence, and a store
followed by a fence, respectively. The amount of fencing may be overkill, but
it reflects exactly what the SM Wasm baseline compiler for AArch64 does.

One reason to implement r-m-w and c-a-s as a single insn which is expanded
only at emission time is that we must be very careful what instructions we
allow in between the load-linked and store-conditional. In particular, we
cannot allow *any* extra memory transactions in there, since -- particularly
on low-end hardware -- that might cause the transaction to fail, hence
deadlocking the generated code. That implies that we can't present the LL/SC
loop to the register allocator as its constituent instructions, since it might
insert spills anywhere. Hence we must present it as a single indivisible
unit, as we do here. It also has the benefit of reducing the total amount of
work the RA has to do.

The only other notable feature of the r-m-w and c-a-s translations into
AArch64 code, is that they both need a scratch register internally. Rather
than faking one up by claiming, in `get_regs` that it modifies an extra
scratch register, and having to have a dummy initialisation of it, these new
instructions (`::LLSC` and `::CAS`) simply use fixed registers in the range
x24-x28. We rely on the RA's ability to coalesce V<-->R copies to make the
cost of the resulting extra copies zero or almost zero. x24-x28 are chosen so
as to be call-clobbered, hence their use is less likely to interfere with long
live ranges that span calls.

One subtlety regarding the use of completely fixed input and output registers
is that we must be careful how the surrounding copy from/to of the arg/result
registers is done. In particular, it is not safe to simply emit copies in
some arbitrary order if one of the arg registers is a real reg. For that
reason, the arguments are first moved into virtual regs if they are not
already there, using a new method `<LowerCtx for Lower>::ensure_in_vreg`.
Again, we rely on coalescing to turn them into no-ops in the common case.

There is also a ridealong fix for the AArch64 lowering case for
`Opcode::Trapif | Opcode::Trapff`, which removes a bug in which two trap insns
in a row were generated.

In the patch as submitted there are 6 "FIXME JRS" comments, which mark things
which I believe to be correct, but for which I would appreciate a second
opinion. Unless otherwise directed, I will remove them for the final commit
but leave the associated code/comments unchanged.

show more ...