arm64: dts: rockchip: add MNT Reform 2 laptop

MNT Reform 2 is an open source laptop with replaceable CPU modules,
including a version with the RK3588-based MNT RCORE[1], which is based
on Firefly's

arm64: dts: rockchip: add MNT Reform 2 laptop

MNT Reform 2 is an open source laptop with replaceable CPU modules,
including a version with the RK3588-based MNT RCORE[1], which is based
on Firefly's iCore-3588Q SoM:

- Rockchip RK3588
- Quad A76 and Quad A55 CPU
- 6 TOPS NPU
- up to 32GB LPDDR4x RAM
- SD Card slot
- Gigabit ethernet port
- HDMI port
- 2x mPCIe ports for WiFi or NVMe
- 3x USB 3.0 Type-A HOST port

[1] https://shop.mntre.com/products/mnt-reform

Co-developed-by: "Lukas F. Hartmann" <[email protected]>
Signed-off-by: "Lukas F. Hartmann" <[email protected]>
Signed-off-by: Patrick Wildt <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...

arm64: dts: rockchip: Add Orange Pi 5 Ultra board

The RK3588 Single Board Computer includes
- eMMC
- microSD
- UART
- 2 PWM LEDs
- RTC
- RTL8125 network controller on PCIe 2.0x1.
- M.2 M-key connect

arm64: dts: rockchip: Add Orange Pi 5 Ultra board

The RK3588 Single Board Computer includes
- eMMC
- microSD
- UART
- 2 PWM LEDs
- RTC
- RTL8125 network controller on PCIe 2.0x1.
- M.2 M-key connector routed to PCIe 3.0x4
- PWM controlled heat sink fan.
- 2 USB2 ports
- lower USB3 port
- upper USB3 port with OTG capability
- Mali GPU
- SPI NOR flash
- Mask Rom button
- Analog audio using es8388 codec via the headset jack and onboard mic
- HDMI1
- HDMI IN

the vcc5v0_usb30 regulator shares the same enable gpio pin as the
vcc5v0_usb20 regulator.

The Orange Pi 5 Ultra is a single board computer powered by the Rockchip
RK3588 with similar board layout as the 5 Max but with the HDMI0 swapped
for HDMI IN.

Signed-off-by: Jimmy Hon <[email protected]>
Tested-By: Johannes Erdfelt <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...

arm64: dts: rockchip: Add Radxa ROCK 4D device tree

The Radxa ROCK 4D board is based on the Rockchip rk3576 SoC.

The device tree adds support for basic devices:
- UART
- SD Card
- Ethernet
- US

arm64: dts: rockchip: Add Radxa ROCK 4D device tree

The Radxa ROCK 4D board is based on the Rockchip rk3576 SoC.

The device tree adds support for basic devices:
- UART
- SD Card
- Ethernet
- USB
- RTC

It has 4 USB ports but only 3 are usable as the top left one is used
for maskrom.

It has a USB-C port that is only used for powering the board.

Signed-off-by: Stephen Chen <[email protected]>
Signed-off-by: Detlev Casanova <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...

arm64: dts: rockchip: add overlay for RK3399 Puma Haikou Video Demo adapter

This adds support for the video-demo-adapter DEVKIT ADDON CAM-TS-A01
(https://embedded.cherry.de/product/development-kit/)

arm64: dts: rockchip: add overlay for RK3399 Puma Haikou Video Demo adapter

This adds support for the video-demo-adapter DEVKIT ADDON CAM-TS-A01
(https://embedded.cherry.de/product/development-kit/) for the Haikou
devkit with RK3399 Puma SoM.

The Video Demo adapter is an adapter connected to the fake PCIe slot
labeled "Video Connector" on the Haikou devkit.

Its main feature is a Leadtek DSI-display with touchscreen and a camera
(that is not supported yet because the expected clock rate by the driver
cannot be exactly reached by the clock driver). To drive these
components a number of additional regulators are grouped on the adapter
as well as a PCA9670 gpio-expander to provide the needed additional
gpio-lines.

Signed-off-by: Quentin Schulz <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...

arm64: dts: rockchip: add overlay for PX30 Ringneck Haikou Video Demo adapter

This adds support for the video-demo-adapter DEVKIT ADDON CAM-TS-A01
(https://embedded.cherry.de/product/development-kit

arm64: dts: rockchip: add overlay for PX30 Ringneck Haikou Video Demo adapter

This adds support for the video-demo-adapter DEVKIT ADDON CAM-TS-A01
(https://embedded.cherry.de/product/development-kit/) for the Haikou
devkit with PX30 Ringneck SoM.

The Video Demo adapter is an adapter connected to the fake PCIe slot
labeled "Video Connector" on the Haikou devkit.

Itss main feature is a Leadtek DSI-display with touchscreen and a camera
(that is not supported yet because the expected clock rate by the driver
cannot be exactly reached by the clock driver). To drive these
components a number of additional regulators are grouped on the adapter
as well as a PCA9670 gpio-expander to provide the needed additional
gpio-lines.

Signed-off-by: Quentin Schulz <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...

arm64: dts: rockchip: add support for HAIKOU-LVDS-9904379 adapter for PX30 Ringneck

The HAIKOU-LVDS-9904379 adapter is an adapter for PX30 Ringneck with the
Haikou carrierboard. It is to be inserted

arm64: dts: rockchip: add support for HAIKOU-LVDS-9904379 adapter for PX30 Ringneck

The HAIKOU-LVDS-9904379 adapter is an adapter for PX30 Ringneck with the
Haikou carrierboard. It is to be inserted in the fake PCIe slot labelled
Video Connector.

This adapter expects an Admatec 9904379 1024x600 LVDS display with
backlight and touchscreen. An EEPROM is also found on the adapter.

This adds support for this adapter on PX30 Ringneck when inserted in
Haikou carrierboard.

Signed-off-by: Quentin Schulz <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...

arm64: dts: rockchip: Add devicetree for the ROC-RK3576-PC

As the name implies, it is built around the RK3576 SoC with 4x Cortex-A72
cores, four Cortex-A53 cores and Mali-G52 MC3 GPU.

Storage optio

arm64: dts: rockchip: Add devicetree for the ROC-RK3576-PC

As the name implies, it is built around the RK3576 SoC with 4x Cortex-A72
cores, four Cortex-A53 cores and Mali-G52 MC3 GPU.

Storage options are EMMC, SD-Card, a 2242 M.2 slot and the possibility to
use UFS 2.0 storage.

Video Output options are a HDMI port, a DSI connector as well as Display-
Port via the TypeC connector (all of them not yet supported).

Networking options are a Low-profile Gigabit Ethernet RJ45 port with
Motorcomm YT8531 PHY as well as WiFi via an AMPAK AP6256 module.

USB ports on the board are 1x USB 3.0 port, 1x USB 2.0 port, 1x USB Type-C
and it comes with 40-pin GPIO header

Signed-off-by: Heiko Stuebner <[email protected]>
Link: https://lore.kernel.org/r/[email protected]

show more ...

arm64: dts: rockchip: minimal support for Pre-ICT tester adapter for RK3588 Jaguar

The Pre-ICT tester adapter connects to RK3588 Jaguar SBC through its
proprietary Mezzanine connector.

It exposes a

arm64: dts: rockchip: minimal support for Pre-ICT tester adapter for RK3588 Jaguar

The Pre-ICT tester adapter connects to RK3588 Jaguar SBC through its
proprietary Mezzanine connector.

It exposes a PCIe Gen2 1x M.2 connector and two proprietary camera
connectors. Support for the latter will come once the rest of the camera
stack is supported.

Additionally, the adapter loops some GPIOs together as well as route
some GPIOs to power rails.

This adapter is used for manufacturing RK3588 Jaguar to be able to test
the Mezzanine connector is properly soldered.

Acked-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Dragan Simic <[email protected]> # Makefile
Signed-off-by: Quentin Schulz <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...

arm64: dts: rockchip: add overlay tests for Rock 5B PCIe overlays

According to commit 40658534756f ("arm64: dts: rockchip: Add rock5b
overlays for PCIe endpoint mode"), Rock 5B can operate in PCIe e

arm64: dts: rockchip: add overlay tests for Rock 5B PCIe overlays

According to commit 40658534756f ("arm64: dts: rockchip: Add rock5b
overlays for PCIe endpoint mode"), Rock 5B can operate in PCIe endpoint
mode. For that to work, the rk3588-rock-5b-pcie-ep.dtbo overlay needs to
be applied on Rock 5B base Device Tree. If that Rock 5B is connected to
another Rock 5B, the latter needs to apply the
rk3588-rock-5b-pcie-srns.dtbo overlay.

In order to make sure the overlays are still valid in the future, let's
add a validation test by applying the overlays on top of the main base
at build time.

Reviewed-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Niklas Cassel <[email protected]>
Reviewed-by: Dragan Simic <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...

arm64: dts: rockchip: add overlay test for Edgeble NCM6A/NCM6B

The Edgeble NCM6A/NCM6B can have WiFi modules connected and this is
handled via an overlay (commit 951d6aaa37fe ("arm64: dts: rockchip:

arm64: dts: rockchip: add overlay test for Edgeble NCM6A/NCM6B

The Edgeble NCM6A/NCM6B can have WiFi modules connected and this is
handled via an overlay (commit 951d6aaa37fe ("arm64: dts: rockchip: Add
Edgeble NCM6A WiFi6 Overlay")).

Despite the name of the overlay, it applies to both NCM6A and NCM6B[1].

In order to make sure the overlay is still valid in the future, let's
add a validation test by applying the overlay on top of the main bases
at build time.

[1] https://lore.kernel.org/linux-rockchip/CA+VMnFyom=2BmJ_nt-At6hTQP0v+Auaw-DkCVbT9mjndMmLKtQ@mail.gmail.com/

Reviewed-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Dragan Simic <[email protected]>
Reviewed-by: Jagan Teki <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...

arm64: dts: rockchip: add overlay test for WolfVision PF5

The WolfVision PF5 can have a PF5 Visualizer display and PF5 IO Expander
board connected to it. Therefore, let's generate an overlay test so

arm64: dts: rockchip: add overlay test for WolfVision PF5

The WolfVision PF5 can have a PF5 Visualizer display and PF5 IO Expander
board connected to it. Therefore, let's generate an overlay test so the
application of the two overlays are validated against the base DTB.

Suggested-by: Michael Riesch <[email protected]>
Reviewed-by: Michael Riesch <[email protected]>
Reviewed-by: Dragan Simic <[email protected]>
Signed-off-by: Quentin Schulz <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...

arm64: dts: rockchip: add dts for Ariaboard Photonicat RK3568

Add dts for Ariaboard Photonicat RK3568.
Partially based on downstream board dts. [1]

Working IO:
Debug UART
SDIO QCA9377 WiFi

arm64: dts: rockchip: add dts for Ariaboard Photonicat RK3568

Add dts for Ariaboard Photonicat RK3568.
Partially based on downstream board dts. [1]

Working IO:
Debug UART
SDIO QCA9377 WiFi and Bluetooth
M.2 E-Key PCIe WiFi and Bluetooth
M.2 B-Key USB Modem WWAN
Ethernet WAN Port
MicroSD Card slot
eMMC
HDMI Output
Mali GPU
USB Type-A

Not working IO:
Ethernet LAN Port (Lack of SGMII support)
Power management MCU on UART4 (Driver pending)

Not working IO in MCU:
Battery voltage sensor
Board temperature sensor
Hardware Power-off
Hardware Watchdog
Network status LED
Real-time clock
USB Charger voltage sensor

About onboard power management MCU:
A heartbeat must be sent to the MCU within 60 seconds,
otherwise the MCU will restart the system.
When powering off, a shutdown command needs to be sent to the MCU.
When the power button is long pressed, the MCU will send a shutdown
command to the system. If system does not shutdown within 60 seconds,
the power will be turned off directly.
MCU only provides voltage for charger and battery.
Manufacturer removed RK8xx PMIC.

[1] https://github.com/photonicat/rockchip_rk3568_kernel/blob/novotech-5.10/arch/arm64/boot/dts/rockchip/rk3568-photonicat-base.dtsi

Signed-off-by: Junhao Xie <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...

arm64: dts: rockchip: add DTs for Firefly ITX-3588J and its Core-3588J SoM

Add the device tree and Makefile update.

Signed-off-by: Shimrra Shai <[email protected]>
Link: https://lore.kernel.org

arm64: dts: rockchip: add DTs for Firefly ITX-3588J and its Core-3588J SoM

Add the device tree and Makefile update.

Signed-off-by: Shimrra Shai <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...

arm64: dts: rockchip: Add Orange Pi 5 Max board

The RK3588 Single Board Computer includes
- eMMC
- microSD
- UART
- 2 PWM LEDs
- RTC
- RTL8125 network controller on PCIe 2.0x1.
- M.2 M-key connector

arm64: dts: rockchip: Add Orange Pi 5 Max board

The RK3588 Single Board Computer includes
- eMMC
- microSD
- UART
- 2 PWM LEDs
- RTC
- RTL8125 network controller on PCIe 2.0x1.
- M.2 M-key connector routed to PCIe 3.0x4
- PWM controlled heat sink fan.
- 2 USB2 ports
- lower USB3 port
- upper USB3 port with OTG capability
- Mali GPU
- SPI NOR flash
- Mask Rom button
- Analog audio using es8388 codec via the headset jack and onboard mic
- HDMI0
- HDMI1

the vcc5v0_usb30 regulator shares the same enable gpio pin as the
vcc5v0_usb20 regulator.

The Orange Pi 5 Max and Orange Pi 5 Ultra are both credit-card sized
boards with similar layout, so these boards will share a common dtsi.
The 5 Max has an extra HDMI0 while the 5 Ultra has a HDMI IN instead.

Signed-off-by: Jimmy Hon <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...

arm64: dts: rockchip: Add Radxa E52C

Radxa E52C[1] is a compact network computer based on the Rockchip
RK3582 SoC:

- Dual Cortex-A76 and quad Cortex-A55 CPU
- 5TOPS NPU
- 2GB/4GB/8GB LPDDR4 RAM
- 1

arm64: dts: rockchip: Add Radxa E52C

Radxa E52C[1] is a compact network computer based on the Rockchip
RK3582 SoC:

- Dual Cortex-A76 and quad Cortex-A55 CPU
- 5TOPS NPU
- 2GB/4GB/8GB LPDDR4 RAM
- 16GB/32GB/64GB on-board eMMC
- microSD card slot
- USB 3.0 Type-A HOST port
- USB Type-C debug port
- USB Type-C power port (5V only)
- 2x 2.5GbE ports

[1] https://radxa.com/products/network-computer/e52c

Signed-off-by: FUKAUMI Naoki <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...

arm64: dts: rockchip: Add BigTreeTech CB2 and Pi2

BigTreeTech CB2 and Pi2 share a lot of hardware configuration, so a
common dtsi file was used to define common nodes and properties. This is
similar

arm64: dts: rockchip: Add BigTreeTech CB2 and Pi2

BigTreeTech CB2 and Pi2 share a lot of hardware configuration, so a
common dtsi file was used to define common nodes and properties. This is
similar to how BigTreeTech CB1 and Pi are implemented.

Signed-off-by: Ivan Sergeev <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...

arm64: dts: rockchip: Add H96 Max V58 TV Box based on RK3588 SoC

H96 Max V58 is a compact Rockchip RK3588 based device that ships
with Android and is meant for use as a TV connected media box.

Its

arm64: dts: rockchip: Add H96 Max V58 TV Box based on RK3588 SoC

H96 Max V58 is a compact Rockchip RK3588 based device that ships
with Android and is meant for use as a TV connected media box.

Its hardware includes:
- Rockchip RK3588 SoC with a small aluminium heatsink
- 4GB or 8GB LPDDR4 RAM
- 32GB or 64GB eMMC 5.1 storage (HS400)
- Onboard AP6275P wireless module providing 802.11ax 2x2 MIMO WiFi
over PCIe connection and Bluetooth 5.3 over UART with two external
detachable antennas
- 1x GbE using the onboard GMAC and an RTL8211F PHY
- 1x USB 2.0 Type-A (also serves as the Maskrom port)
- 1x USB 3.0 Type-A
- 1x HDMI 2.1 output
- 1x optical SPDIF output
- LED line display ("88:88" digits plus icons) driven by an FD6551
IC connected over bitbanged I2C (not yet enabled here)
- GPIO connected CIR receiver
- Single Rockchip RK806-1 PMIC
- 12x onboard ambient LEDs lighting up the bottom of the device
- 5v DCIN using a standard round 5.5mm connector

Signed-off-by: Alexey Charkov <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...

arm64: dts: rockchip: Add rk3576 evb1 board

RK3576 EVB1 board features:
- Rockchip RK3576
- PMIC: RK806-2x2pcs+DiscretePower
- RAM: LPDDR4/4x 2pcsx 32bit
- ROM: eMMC5.1 + UFS
- LAN x 2
- HDMI TX
- S

arm64: dts: rockchip: Add rk3576 evb1 board

RK3576 EVB1 board features:
- Rockchip RK3576
- PMIC: RK806-2x2pcs+DiscretePower
- RAM: LPDDR4/4x 2pcsx 32bit
- ROM: eMMC5.1 + UFS
- LAN x 2
- HDMI TX
- SD card slot
- PCIe2 slot

Add support for pmic, eMMC, SD-card, ADC-KEY, PCIE and GMAC.

NOTE: The board has a hardware mux design for
- PCIe slot(pcie1)
- USB3 host(usb_drd1_dwc3)
and default state is switch to USB3. To enable PCIe slot:
- hardware: Switch the mux to PCIe side;
- dts: disable usb_drd1_dwc3 and enable pcie1;

Signed-off-by: Liang Chen <[email protected]>
Signed-off-by: Kever Yang <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...

arm64: dts: rockchip: add Radxa ROCK 5C

Radxa ROCK 5C is a 8K computer for everything[1] using the Rockchip
RK3588S2 chip:

- Rockchip RK3588S2
- Quad A76 and Quad A55 CPU
- 6 TOPS NPU
- up to 32GB

arm64: dts: rockchip: add Radxa ROCK 5C

Radxa ROCK 5C is a 8K computer for everything[1] using the Rockchip
RK3588S2 chip:

- Rockchip RK3588S2
- Quad A76 and Quad A55 CPU
- 6 TOPS NPU
- up to 32GB LPDDR4x RAM
- eMMC / SPI flash connector
- Micro SD Card slot
- Gigabit ethernet port (supports PoE with add-on PoE HAT)
- WiFi6 / BT5.4
- 1x USB 3.0 Type-A HOST port
- 1x USB 3.0 Type-A OTG port
- 2x USB 2.0 Type-A HOST port
- 1x USB Type-C 5V power port

[1] https://radxa.com/products/rock5/5c

Signed-off-by: FUKAUMI Naoki <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...

arm64: dts: rockchip: add Banana Pi P2 Pro board

Banana Pi P2 Pro is the SBC made by Shenzhen SINOVOIP based on
Rockchip RK3308.

Banana Pi P2 Pro features:
- Rockchip RK3308B-S
- DDR3 512 MB
- eMMC

arm64: dts: rockchip: add Banana Pi P2 Pro board

Banana Pi P2 Pro is the SBC made by Shenzhen SINOVOIP based on
Rockchip RK3308.

Banana Pi P2 Pro features:
- Rockchip RK3308B-S
- DDR3 512 MB
- eMMC 8 GB
- 100M lan + onboard PoE
- 40 pin and 12 pin headers
- AP6256 BT + WIFI
- TF card slot
- 2x USB 2.0 (Type-C OTG and Type-A)
- Headphone jack

Add support for Banana Pi P2 Pro.

Signed-off-by: Dmitry Yashin <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...

arm64: dts: rockchip: sort rk3588s-rock5a properly in Makefile

sort target dtb files properly in Makefile for rockchip.

Signed-off-by: FUKAUMI Naoki <[email protected]>
Link: https://lore.kernel.org/

arm64: dts: rockchip: sort rk3588s-rock5a properly in Makefile

sort target dtb files properly in Makefile for rockchip.

Signed-off-by: FUKAUMI Naoki <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...

arm64: dts: rockchip: Add rk3588-orangepi-5b device tree

Implements a slightly modified rk3588s-orangepi-5b.dts from the vendor.
Unfortunately the &wireless_bluetooth and &wireless_wlan are not
impl

arm64: dts: rockchip: Add rk3588-orangepi-5b device tree

Implements a slightly modified rk3588s-orangepi-5b.dts from the vendor.
Unfortunately the &wireless_bluetooth and &wireless_wlan are not
implemented yet.

Therefore add the sdhci alias to be mmc0 on the rk3588s-orangepi-5b.dts.

How is the Orange Pi 5B unique?
- the Orange Pi 5b uses combphy0_ps for the WiFi.
- the Orange Pi 5B has GPIO0_C5 hooked to BT_WAKE_HOST.
- builtin eMMC storage
- ap6275p Wifi module (like the Orange Pi 5 Plus)
- builtin BlueTooth module

Signed-off-by: Cenk Uluisik <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...

arm64: dts: rockchip: Add FriendlyARM NanoPi R3S board

The NanoPi R3S(as "R3S") is an open source platform with dual-Gbps
Ethernet ports designed and developed by FriendlyElec for IoT
applications.

arm64: dts: rockchip: Add FriendlyARM NanoPi R3S board

The NanoPi R3S(as "R3S") is an open source platform with dual-Gbps
Ethernet ports designed and developed by FriendlyElec for IoT
applications.

Specification:
- Rockchip RK3566
- 2GB LPDDR4X RAM
- optional 32GB eMMC module
- SD card slot
- 2x 1000 Base-T
- 3x LEDs (POWER, LAN, WAN)
- 2x Buttons (Reset, MaskROM)
- 1x USB 3.0 Port
- Type-C 5V 2A Power

Signed-off-by: Tianling Shen <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...

arm64: dts: rockchip: Add Radxa e20c board

Add board-level device tree for Radxa e20c board[1]. This basic
implementation supports boot into a kernel with only UART console.
Other features will be a

arm64: dts: rockchip: Add Radxa e20c board

Add board-level device tree for Radxa e20c board[1]. This basic
implementation supports boot into a kernel with only UART console.
Other features will be added later.

[1]: https://docs.radxa.com/en/e/e20c

Signed-off-by: Yao Zi <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...

arm64: dts: rockchip: Add rk3576-armsom-sige5 board

Add board file for the rk3576 based ArmSoM Sige5 board. While the hardware
offers plenty of peripherals and connectivity this basic implementation

arm64: dts: rockchip: Add rk3576-armsom-sige5 board

Add board file for the rk3576 based ArmSoM Sige5 board. While the hardware
offers plenty of peripherals and connectivity this basic implementation
just handles things required to successfully boot Linux from SD card and
connect via UART or Ethernet.

Signed-off-by: Detlev Casanova <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Heiko Stuebner <[email protected]>

show more ...