ARM: dts: Move .dts files to vendor sub-directories

The arm dts directory has grown to 1559 boards which makes it a bit
unwieldy to maintain and use. Past attempts stalled out due to plans to
move .

ARM: dts: Move .dts files to vendor sub-directories

The arm dts directory has grown to 1559 boards which makes it a bit
unwieldy to maintain and use. Past attempts stalled out due to plans to
move .dts files out of the kernel tree. Doing that is no longer planned
(any time soon at least), so let's go ahead and group .dts files by
vendors. This move aligns arm with arm64 .dts file structure.

There's no change to dtbs_install as the flat structure is maintained on
install.

The naming of vendor directories is roughly in this order of preference:
- Matching original and current SoC vendor prefix/name (e.g. ti, qcom)
- Current vendor prefix/name if still actively sold (SoCs which have
been aquired) (e.g. nxp/imx)
- Existing platform name for older platforms not sold/maintained by any
company (e.g. gemini, nspire)

The whole move was scripted with the exception of MAINTAINERS and a few
makefile fixups.

Acked-by: Viresh Kumar <[email protected]>
Acked-by: Michal Simek <[email protected]> #Xilinx
Acked-by: Krzysztof Kozlowski <[email protected]>
Acked-by: Neil Armstrong <[email protected]>
Acked-by: Paul Barker <[email protected]>
Acked-by: Tony Lindgren <[email protected]>
Acked-by: Gregory CLEMENT <[email protected]>
Acked-by: Heiko Stuebner <[email protected]>
Acked-by: Wei Xu <[email protected]> #hisilicon
Acked-by: Geert Uytterhoeven <[email protected]>
Acked-by: Nick Hawkins <[email protected]>
Acked-by: Baruch Siach <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
Reviewed-by: Andre Przywara <[email protected]>
Acked-by: Andre Przywara <[email protected]>
Reviewed-by: Claudiu Beznea <[email protected]>
Acked-by: Peter Rosin <[email protected]>
Acked-by: Jesper Nilsson <[email protected]>
Acked-by: Sudeep Holla <[email protected]>
Acked-by: Florian Fainelli <[email protected]> #broadcom
Acked-by: Manivannan Sadhasivam <[email protected]>
Reviewed-by: Jisheng Zhang <[email protected]>
Acked-by: Patrice Chotard <[email protected]>
Acked-by: Romain Perier <[email protected]>
Acked-by: Alexandre TORGUE <[email protected]>
Acked-by: Shawn Guo <[email protected]>
Acked-by: Kunihiko Hayashi <[email protected]>
Acked-by: Enric Balletbo i Serra <[email protected]>
Signed-off-by: Rob Herring <[email protected]>

show more ...

ARM: dts: Add .dts files missing from the build

Comparing .dts files to built .dtb files yielded a few .dts files which
are never built. Add them to the build.

Signed-off-by: Rob Herring <robh@kern

ARM: dts: Add .dts files missing from the build

Comparing .dts files to built .dtb files yielded a few .dts files which
are never built. Add them to the build.

Signed-off-by: Rob Herring <[email protected]>

show more ...

ARM: dts: at91: Enable device-tree overlay support for AT91 boards

Add the '-@' DTC option for AT91 boards that have device-tree overlays.
This option populates the '__symbols__' node that contains

ARM: dts: at91: Enable device-tree overlay support for AT91 boards

Add the '-@' DTC option for AT91 boards that have device-tree overlays.
This option populates the '__symbols__' node that contains all the
necessary symbols for supporting device-tree overlays (from bootloader)
on these devices.

This change increases the size of the resulting DTB with ~30%-40%. Below
are the measurements performed v6.4-rc6:

at91-sam9x60_curiosity.dtb 28499 -> 36641 bytes
at91-sam9x60ek.dtb 30867 -> 39609 bytes
at91-sama5d27_som1_ek.dtb 26086 -> 34166 bytes
at91-sama5d27_wlsom1_ek.dtb 26045 -> 33184 bytes
at91-sama5d2_icp.dtb 27521 -> 36155 bytes
at91-sama5d2_ptc_ek.dtb 23237 -> 29612 bytes
at91-sama5d2_xplained.dtb 27262 -> 35326 bytes
at91-sama5d3_eds.dtb 27924 -> 39939 bytes
at91-sama5d3_xplained.dtb 28400 -> 40650 bytes
at91-sama5d4_xplained.dtb 26456 -> 36107 bytes
at91-sama7g5ek.dtb 29212 -> 37289 bytes

Signed-off-by: Cristian Birsan <[email protected]>
[claudiu.beznea: s/arm: dts/ARM: dts: at91/ in commit title]
Signed-off-by: Claudiu Beznea <[email protected]>
Link: https://lore.kernel.org/r/[email protected]

show more ...

arm: dts: Enable device-tree overlay support for AT91 boards

Add the '-@' DTC option for AT91 boards that have device-tree overlays.
This option populates the '__symbols__' node that contains all th

arm: dts: Enable device-tree overlay support for AT91 boards

Add the '-@' DTC option for AT91 boards that have device-tree overlays.
This option populates the '__symbols__' node that contains all the
necessary symbols for supporting device-tree overlays (from bootloader)
on these devices.

This change increases the size of the resulting DTB with ~30%-40%. Below
are the measurements performed v6.4-rc6:

at91-sam9x60_curiosity.dtb 28499 -> 36641 bytes
at91-sam9x60ek.dtb 30867 -> 39609 bytes
at91-sama5d27_som1_ek.dtb 26086 -> 34166 bytes
at91-sama5d27_wlsom1_ek.dtb 26045 -> 33184 bytes
at91-sama5d2_icp.dtb 27521 -> 36155 bytes
at91-sama5d2_ptc_ek.dtb 23237 -> 29612 bytes
at91-sama5d2_xplained.dtb 27262 -> 35326 bytes
at91-sama5d3_eds.dtb 27924 -> 39939 bytes
at91-sama5d3_xplained.dtb 28400 -> 40650 bytes
at91-sama5d4_xplained.dtb 26456 -> 36107 bytes
at91-sama7g5ek.dtb 29212 -> 37289 bytes

Signed-off-by: Cristian Birsan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Arnd Bergmann <[email protected]>

show more ...

ARM: dts: qcom: Add Samsung Galaxy Express support

Add a very basic device tree file for the Samsung Galaxy Express SGH-I437.
Currently, the following things work: UART, eMMC, SD Card, and USB.

Sig

ARM: dts: qcom: Add Samsung Galaxy Express support

Add a very basic device tree file for the Samsung Galaxy Express SGH-I437.
Currently, the following things work: UART, eMMC, SD Card, and USB.

Signed-off-by: Rudraksha Gupta <[email protected]>
Signed-off-by: Bjorn Andersson <[email protected]>
Link: https://lore.kernel.org/r/[email protected]

show more ...

arm: dts: bcm: Enable device-tree overlay support for RPi devices

Add the '-@' DTC option for the Raspberry Pi devices. This option
populates the '__symbols__' node that contains all the necessary s

arm: dts: bcm: Enable device-tree overlay support for RPi devices

Add the '-@' DTC option for the Raspberry Pi devices. This option
populates the '__symbols__' node that contains all the necessary symbols
for supporting device-tree overlays (for instance from the firmware or
the bootloader) on these devices.

The Rasbperry Pi devices are well known for their GPIO header, that
allow various "HATs" or other modules do be connected and this enables
users to create out-of-tree device-tree overlays for these modules.

Please note that this change does increase the size of the resulting DTB
by ~40%. For example, with v6.4-rc1 increase in size is as follows:

bcm2711-rpi-400.dtb 27556 -> 38141 bytes
bcm2711-rpi-4-b.dtb 27484 -> 38069 bytes
bcm2711-rpi-cm4-io.dtb 27373 -> 38076 bytes
bcm2835-rpi-a.dtb 12879 -> 18235 bytes
bcm2835-rpi-a-plus.dtb 13015 -> 18371 bytes
bcm2835-rpi-b.dtb 12997 -> 18377 bytes
bcm2835-rpi-b-plus.dtb 13237 -> 18666 bytes
bcm2835-rpi-b-rev2.dtb 13085 -> 18514 bytes
bcm2835-rpi-cm1-io1.dtb 13109 -> 18528 bytes
bcm2835-rpi-zero.dtb 12923 -> 18311 bytes
bcm2835-rpi-zero-w.dtb 13449 -> 18889 bytes
bcm2836-rpi-2-b.dtb 14500 -> 20252 bytes
bcm2837-rpi-3-a-plus.dtb 14930 -> 20713 bytes
bcm2837-rpi-3-b.dtb 15107 -> 20979 bytes
bcm2837-rpi-3-b-plus.dtb 15463 -> 21443 bytes
bcm2837-rpi-cm3-io3.dtb 14429 -> 20098 bytes
bcm2837-rpi-zero-2-w.dtb 14781 -> 20524 bytes

Signed-off-by: Aurelien Jarno <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
[ukleinek: rebased to v6.4-rc1]
Signed-off-by: Uwe Kleine-König <[email protected]>
Acked-by: Conor Dooley <[email protected]>
Signed-off-by: Florian Fainelli <[email protected]>

show more ...

ARM: dts: omap4: add initial support for Epson Moverio BT-200

Add the devices working with current drivers for the
Epson Moverio BT-200 AR glasses consisting of a control unit
and the glasses itself

ARM: dts: omap4: add initial support for Epson Moverio BT-200

Add the devices working with current drivers for the
Epson Moverio BT-200 AR glasses consisting of a control unit
and the glasses itself.

Signed-off-by: Andreas Kemnade <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>

show more ...

arm: dts: sunxi: Add ICnova A20 ADB4006 board

Add board support for ICnova A20 SomPi compute module on
ICnova ADB4006 development board.

Specification:
SoM
- Processor: Allwinner A20 Cortex-A7 Dual

arm: dts: sunxi: Add ICnova A20 ADB4006 board

Add board support for ICnova A20 SomPi compute module on
ICnova ADB4006 development board.

Specification:
SoM
- Processor: Allwinner A20 Cortex-A7 Dual Core at 1GHz
- 512MB DDR3 RAM
- Fast Ethernet (Phy: Realtek RTL8201CP)
ADB4006
- I2C
- 2x USB 2.0
- 1x Fast Ethernet port
- 1x SATA
- 2x buttons (PWRON, Boot)
- 2x LEDS
- serial console
- HDMI
- µSD-Card slot
- Audio Line-In / Line-Out
- GPIO pinheaders

https://wiki.in-circuit.de/index.php5?title=ICnova_ADB4006
https://wiki.in-circuit.de/index.php5?title=ICnova_A20_SODIMM

Reviewed-by: Andre Przywara <[email protected]>
Signed-off-by: Ludwig Kormann <[email protected]>
Reviewed-by: Jernej Skrabec <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jernej Skrabec <[email protected]>

show more ...

ARM: dts: stm32: add STM32MP1-based Phytec board

Add the Phytec STM32MP1-3 Dev board. The devboard uses a Phytec
stm32m157c-som.

Signed-off-by: Steffen Trumtrar <[email protected]>
Signed-o

ARM: dts: stm32: add STM32MP1-based Phytec board

Add the Phytec STM32MP1-3 Dev board. The devboard uses a Phytec
stm32m157c-som.

Signed-off-by: Steffen Trumtrar <[email protected]>
Signed-off-by: Alexandre Torgue <[email protected]>

show more ...

ARM: dts: imx6ull-dhcor: Add Marantec maveo box

Add support for Marantec maveo box. The system is used to get a
smart conntection to a door drive. It has USB, WiFi, Bluetooth,
Zigbee and NFC interfa

ARM: dts: imx6ull-dhcor: Add Marantec maveo box

Add support for Marantec maveo box. The system is used to get a
smart conntection to a door drive. It has USB, WiFi, Bluetooth,
Zigbee and NFC interfaces. The core of this system is a soldered
i.MX6ULL DHCOR SoM from DH electronics.

Signed-off-by: Christoph Niedermaier <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>

show more ...

ARM: dts: kirkwood: Add Endian 4i Edge 200 board

Add Endian 4i Edge 200 is 5-port firewall.
It have also clone: Endian UTM Mini (The same hardware, with added WLAN
card).

Hardware:
- SoC: Marvell

ARM: dts: kirkwood: Add Endian 4i Edge 200 board

Add Endian 4i Edge 200 is 5-port firewall.
It have also clone: Endian UTM Mini (The same hardware, with added WLAN
card).

Hardware:
- SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz
- Ram: 512MB (4x Nanya NT5TU128M8GE-AC)
- NAND Flash: 512MB (Micron 29F4G08AAC)
- Lan 1-4: 4x GBE (Marvell 88E6171R-TFJ2)
- Lan 5: 1x GBE (Marvell 88E1116R-NNC1)
- Storage: MicroSD Slot
- MCPIE: MiniPCIe Slot present [fitted with SparkLan WPEA-110N/E
(Atheros AR9280 chipset) in Endian UTM Mini WLAN only]
- USB: 1x USB 2.0 port
- Console: RJ-45 port
- LEDs: 3x GPIO controlled

Signed-off-by: Pawel Dembicki <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: Gregory CLEMENT <[email protected]>

show more ...

ARM: dts: imx6ull: Add chargebyte Tarragon support

This adds the support for chargebyte Tarragon, which is an Electrical
Vehicle Supply Equipment (EVSE) for AC charging stations
(according to IEC 61

ARM: dts: imx6ull: Add chargebyte Tarragon support

This adds the support for chargebyte Tarragon, which is an Electrical
Vehicle Supply Equipment (EVSE) for AC charging stations
(according to IEC 61851, ISO 15118).

The Tarragon board is based on an i.MX6ULL SoC and is available in
4 variants (Master, Slave, SlaveXT, Micro), which provide more or
less peripherals.

Supported features:
* 512 MB DDR RAM
* eMMC
* Debug UART
* 100 Mbit Ethernet
* USB 2.0 Host interface
* Powerline communication (QCA700x)
* 2x RS485
* Digital in- and outputs (12 V)
* One-Wire master for external temp sensors
* 2x relay outputs
* 2x motor interfaces

Link: https://chargebyte.com/products/charging-station-communication/charge-control-c
Signed-off-by: Stefan Wahren <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>

show more ...

ARM: dts: oxnas: remove obsolete device tree files

Due to lack of maintainance and stall of development for a few years now,
and since no new features will ever be added upstream, remove support
for

ARM: dts: oxnas: remove obsolete device tree files

Due to lack of maintainance and stall of development for a few years now,
and since no new features will ever be added upstream, remove support
for OX810 and OX820 devices.

Acked-by: Linus Walleij <[email protected]>
Acked-by: Arnd Bergmann <[email protected]>
Acked-by: Daniel Golle <[email protected]>
Signed-off-by: Neil Armstrong <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>

show more ...

ARM: dts: sunxi: add MangoPi MQ-R-T113 board

The MangoPi MQ-R-T113 is a small SBC with the Allwinner T113-s3 SoC.
The SoC features two Arm Cortex-A7 cores and 128 MB of co-packaged DDR3
DRAM. The bo

ARM: dts: sunxi: add MangoPi MQ-R-T113 board

The MangoPi MQ-R-T113 is a small SBC with the Allwinner T113-s3 SoC.
The SoC features two Arm Cortex-A7 cores and 128 MB of co-packaged DDR3
DRAM. The board adds mostly connectors and the required regulators, plus
a Realtek RTL8189FTV WiFi chip.
Power comes in via a USB-C connector wired as a peripheral, and there is
a second USB-C connector usable as a host port.

Add a .dtsi file describing most of the board's peripherals, and include
that from the actual board .dts file. This allows to re-use the .dtsi
for the MQ-R-F113 RISC-V variant of that board.

Signed-off-by: Andre Przywara <[email protected]>
Acked-by: Jernej Skrabec <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jernej Skrabec <[email protected]>

show more ...

ARM: dts: am57xx-idk: Add IDK displays and touchscreens

This is a more interesting use of DT Overlays than the previous patches.
Here we have two touchscreen modules. Each is compatible with, and ca

ARM: dts: am57xx-idk: Add IDK displays and touchscreens

This is a more interesting use of DT Overlays than the previous patches.
Here we have two touchscreen modules. Each is compatible with, and can be
attached to, either of the two AM57xx IDK development board variants
(AM571x or AM572x).

Due to the way the extension header was wired on the development boards,
the touch sensor on the touchscreen modules will connect to different
SoC pins when connected. For this the touch sensor is modeled as an
additional overlay that is specific to the development board for which it
is connected.

Basically the LCD overlay can be swapped, but the touchscreen overlay
that attaches to the LCD must be used with the corresponding base DT
and not to the LCD.

AM571x -\ /- osd101t2045.dtbo -\ /- am571x-idk-touchscreen.dtbo
X X
AM572x -/ \- osd101t2587.dtbo -/ \- am572x-idk-touchscreen.dtbo

Signed-off-by: Andrew Davis <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>

show more ...

ARM: dts: ti: Add AM57xx GP EVM Rev A3 board support

The A3 revision of the AM57xx GP EVM has the same EVM feature set as the
original but is paired with an updated revision C BeagleBoard X15.

DT O

ARM: dts: ti: Add AM57xx GP EVM Rev A3 board support

The A3 revision of the AM57xx GP EVM has the same EVM feature set as the
original but is paired with an updated revision C BeagleBoard X15.

DT Overlays allow us to model this in the same way, we simply apply the
EVM overlay to the Rev C BeagleBoard to create the Rev A3 AM57xx GP EVM.

Signed-off-by: Andrew Davis <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>

show more ...

ARM: dts: ti: Add AM57xx GP EVM board support

The AM57xx GP EVM boards are built on top the AM57xx BeagleBoard-X15.
The EVM extends the BeagleBoard by adding a touchscreen, some buttons,
and a handf

ARM: dts: ti: Add AM57xx GP EVM board support

The AM57xx GP EVM boards are built on top the AM57xx BeagleBoard-X15.
The EVM extends the BeagleBoard by adding a touchscreen, some buttons,
and a handful of peripheral extension slots.

Being a plugin extension of an existing standalone board; we define
the am57xx-evm as a composite-DTB of the base am57xx-beagle-x15
and a new am57xx-evm overlay.

Signed-off-by: Tero Kristo <[email protected]>
Signed-off-by: Tomi Valkeinen <[email protected]>
Signed-off-by: Suman Anna <[email protected]>
Signed-off-by: Andrew Davis <[email protected]>
Message-Id: <[email protected]>
Signed-off-by: Tony Lindgren <[email protected]>

show more ...

ARM: dts: imx: Add devicetree for Tolino Vison

Add a devicetree for the Tolino Vision Ebook reader. It is based
on boards marked with "37NB-E60Q30+4A3". It is equipped with an i.MX6SL
SoC.

Expected

ARM: dts: imx: Add devicetree for Tolino Vison

Add a devicetree for the Tolino Vision Ebook reader. It is based
on boards marked with "37NB-E60Q30+4A3". It is equipped with an i.MX6SL
SoC.

Expected to work:
- Buttons
- Wifi
- LEDs
- uSD
- eMMC
- USB
- RTC
- Touchscreen
- Backlight

Signed-off-by: Andreas Kemnade <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>

show more ...

ARM: dts: imx6dl-yapp43: Add support for new HW revision of the IOTA board

The PCB used for all the current boards (Ursa, Draco, Hydra, Orion, Crux)
was slightly redesigned and delivers some new fea

ARM: dts: imx6dl-yapp43: Add support for new HW revision of the IOTA board

The PCB used for all the current boards (Ursa, Draco, Hydra, Orion, Crux)
was slightly redesigned and delivers some new features while some unused
components were removed.

- External RTC chip with supercap added.
- Secure element added.
- LCD display power supply enable/disable signal added.
- Touch keyboard reset and interrupt signals added.
- Factory reset GPIO button added.
- Audio codec LM49350 (EoL) removed and replaced by PWM audio output.
- QCA8334 switch was replaced by Marvell 88E6141.
- PCIe completely removed.
- uSD card removed and replaced by board-to-board expansion connector.

There are four configuration variants of the new board:

1. Pegasus
The board configuration is based on Orion with the following major changes:

- Quad core SoC
- 4GB of RAM
- RTC with supercap added
- Secure element added

2. Pegasus+
This is the very same board as Pegasus but uses the i.MX6QuadPlus SoC.

3. Lynx
The board configuration is based on Draco with the following major changes:

- DualLite SoC
- 1GB of RAM
- RTC with supercap added
- Secure element added

4. Phoenix
The board configuration is based on Ursa with the following major changes:

- DualLite Soc
- 1GB of RAM
- RTC with supercap added
- Secure element added
- LCD display support removed
- UART2 removed
- Factory reset GPIO button added

Signed-off-by: Michal Vokáč <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>

show more ...

ARM: dts: suniv: Add Lctech Pi F1C200s devicetree

The Lctech Pi F1C200s (also previously known under the Cherry Pi brand)
is a small development board with the Allwinner F1C200s SoC. This is the
sam

ARM: dts: suniv: Add Lctech Pi F1C200s devicetree

The Lctech Pi F1C200s (also previously known under the Cherry Pi brand)
is a small development board with the Allwinner F1C200s SoC. This is the
same as the F1C100s, but with 64MB instead of 32MB co-packaged DRAM.

Alongside the obligatory micro-SD card slot, the board features a
SPI-NAND flash chip, LCD and touch connectors, and unpopulated
expansion header pins.
There are two USB Type-C ports on the board: One supplies the power, also
connects to the USB MUSB OTG controller port. The other one is connected
to an CH340 USB serial chip, which in turn is connected to UART1.

Add a devicetree file, so that the board can be used easily.

Signed-off-by: Andre Przywara <[email protected]>
Acked-by: Jernej Skrabec <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jernej Skrabec <[email protected]>

show more ...

ARM: dts: suniv: add device tree for PopStick v1.1

PopStick is a minimal Allwinner F1C200s dongle, with its USB controller
wired to a USB Type-A plug, a SD slot and a SPI NAND flash on board, and
an

ARM: dts: suniv: add device tree for PopStick v1.1

PopStick is a minimal Allwinner F1C200s dongle, with its USB controller
wired to a USB Type-A plug, a SD slot and a SPI NAND flash on board, and
an on-board CH340 USB-UART converted connected to F1C200s's UART0.

Add a device tree for it. As F1C200s is just F1C100s with a different
DRAM chip co-packaged, directly use F1C100s DTSI here.

This commit covers the v1.1 version of this board, which is now shipped.
v1.0 is some internal sample that have not been shipped at all.

Signed-off-by: Icenowy Zheng <[email protected]>
Signed-off-by: Andre Przywara <[email protected]>
Acked-by: Jernej Skrabec <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jernej Skrabec <[email protected]>

show more ...

ARM: dts: socfpga: Add enclustra PE1 devicetree

The enclustra PE1 is a baseboard from enclustra GmbH for the enclustra
Mercury AA1+ SOM.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro

ARM: dts: socfpga: Add enclustra PE1 devicetree

The enclustra PE1 is a baseboard from enclustra GmbH for the enclustra
Mercury AA1+ SOM.

Reviewed-by: Krzysztof Kozlowski <[email protected]>
Signed-off-by: Steffen Trumtrar <[email protected]>
Signed-off-by: Dinh Nguyen <[email protected]>

show more ...

ARM: dts: at91: sam9x60_curiosity: Add device tree for sam9x60 curiosity board

Add device tree file for sam9x60 curiosity board.

Signed-off-by: Durai Manickam KR <[email protected]>
Re

ARM: dts: at91: sam9x60_curiosity: Add device tree for sam9x60 curiosity board

Add device tree file for sam9x60 curiosity board.

Signed-off-by: Durai Manickam KR <[email protected]>
Reviewed-by: Claudiu Beznea <[email protected]>
Signed-off-by: Claudiu Beznea <[email protected]>
Link: https://lore.kernel.org/r/[email protected]

show more ...

ARM: dts: imx6ull-dhcom: Add DHSOM based DRC02 board

Add DT for DH DRC02 unit, which is a universal controller device.
The system has two ethernet ports, two CANs, RS485 and RS232, USB,
capacitive b

ARM: dts: imx6ull-dhcom: Add DHSOM based DRC02 board

Add DT for DH DRC02 unit, which is a universal controller device.
The system has two ethernet ports, two CANs, RS485 and RS232, USB,
capacitive buttons and an OLED display. For this board a DHCOM
i.MX6ULL SoM configuration without WiFi/BT is used. The interface
is used for the SD card instead.

Signed-off-by: Christoph Niedermaier <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>

show more ...

ARM: dts: imx6ull-dhcom: Add DHCOM based PicoITX board

Add DT for DH PicoITX unit, which is a bare-bones carrier board for
the DHCOM. The board has ethernet port, USB, CAN, LED and a custom
board-to

ARM: dts: imx6ull-dhcom: Add DHCOM based PicoITX board

Add DT for DH PicoITX unit, which is a bare-bones carrier board for
the DHCOM. The board has ethernet port, USB, CAN, LED and a custom
board-to-board expansion connector. For this board a DHCOM i.MX6ULL
SoM configuration without WiFi/BT is used. The interface is used
for the SD card instead. Make this adjustment by using a separate DT
include file.

Signed-off-by: Christoph Niedermaier <[email protected]>
Reviewed-by: Marek Vasut <[email protected]>
Signed-off-by: Shawn Guo <[email protected]>

show more ...