lib/raid6: Drop IA64 support

Drop Itanium support from the RAID6 code, and along with it, the 16x and
32x unrolled versions, which were only used by IA64.

Signed-off-by: Ard Biesheuvel <ardb@kernel

lib/raid6: Drop IA64 support

Drop Itanium support from the RAID6 code, and along with it, the 16x and
32x unrolled versions, which were only used by IA64.

Signed-off-by: Ard Biesheuvel <[email protected]>

show more ...

md/raid6 algorithms: xor_syndrome() for generic int

Start the algorithms with the very basic one. It is left and right
optimized. That means we can avoid all calculations for unneeded pages
above th

md/raid6 algorithms: xor_syndrome() for generic int

Start the algorithms with the very basic one. It is left and right
optimized. That means we can avoid all calculations for unneeded pages
above the right stop offset. For pages below the left start offset we
still need the syndrome multiplication but without reading data pages.

Signed-off-by: Markus Stockhausen <[email protected]>
Signed-off-by: NeilBrown <[email protected]>

show more ...

md/raid6 algorithms: delta syndrome functions

v3: s-o-b comment, explanation of performance and descision for
the start/stop implementation

Implementing rmw functionality for RAID6 requires optimiz

md/raid6 algorithms: delta syndrome functions

v3: s-o-b comment, explanation of performance and descision for
the start/stop implementation

Implementing rmw functionality for RAID6 requires optimized syndrome
calculation. Up to now we can only generate a complete syndrome. The
target P/Q pages are always overwritten. With this patch we provide
a framework for inplace P/Q modification. In the first place simply
fill those functions with NULL values.

xor_syndrome() has two additional parameters: start & stop. These
will indicate the first and last page that are changing during a
rmw run. That makes it possible to avoid several unneccessary loops
and speed up calculation. The caller needs to implement the following
logic to make the functions work.

1) xor_syndrome(disks, start, stop, ...): "Remove" all data of source
blocks inside P/Q between (and including) start and end.

2) modify any block with start <= block <= stop

3) xor_syndrome(disks, start, stop, ...): "Reinsert" all data of
source blocks into P/Q between (and including) start and end.

Pages between start and stop that won't be changed should be filled
with a pointer to the kernel zero page. The reasons for not taking NULL
pages are:

1) Algorithms cross the whole source data line by line. Thus avoid
additional branches.

2) Having a NULL page avoids calculating the XOR P parity but still
need calulation steps for the Q parity. Depending on the algorithm
unrolling that might be only a difference of 2 instructions per loop.

The benchmark numbers of the gen_syndrome() functions are displayed in
the kernel log. Do the same for the xor_syndrome() functions. This
will help to analyze performance problems and give an rough estimate
how well the algorithm works. The choice of the fastest algorithm will
still depend on the gen_syndrome() performance.

With the start/stop page implementation the speed can vary a lot in real
life. E.g. a change of page 0 & page 15 on a stripe will be harder to
compute than the case where page 0 & page 1 are XOR candidates. To be not
to enthusiatic about the expected speeds we will run a worse case test
that simulates a change on the upper half of the stripe. So we do:

1) calculation of P/Q for the upper pages

2) continuation of Q for the lower (empty) pages

Signed-off-by: Markus Stockhausen <[email protected]>
Signed-off-by: NeilBrown <[email protected]>

show more ...

lib/raid6: Fix filename emitted in generated code

The files were renamed in commit cc4589ebf; fix the name in the file
itself.

Signed-off-by: Dan McGee <[email protected]>
Signed-off-by: NeilBrown

lib/raid6: Fix filename emitted in generated code

The files were renamed in commit cc4589ebf; fix the name in the file
itself.

Signed-off-by: Dan McGee <[email protected]>
Signed-off-by: NeilBrown <[email protected]>

show more ...

Rename raid6 files now they're in a 'raid6' directory.

Linus asks 'why "raid6" twice?'. No reason.

Signed-off-by: David Woodhouse <[email protected]>