|
Revision tags: v6.15, v6.15-rc7, v6.15-rc6, v6.15-rc5, v6.15-rc4, v6.15-rc3, v6.15-rc2, v6.15-rc1, v6.14, v6.14-rc7, v6.14-rc6, v6.14-rc5, v6.14-rc4, v6.14-rc3, v6.14-rc2, v6.14-rc1, v6.13, v6.13-rc7, v6.13-rc6, v6.13-rc5, v6.13-rc4, v6.13-rc3, v6.13-rc2, v6.13-rc1, v6.12, v6.12-rc7, v6.12-rc6, v6.12-rc5, v6.12-rc4, v6.12-rc3, v6.12-rc2, v6.12-rc1, v6.11, v6.11-rc7, v6.11-rc6, v6.11-rc5, v6.11-rc4, v6.11-rc3, v6.11-rc2, v6.11-rc1, v6.10, v6.10-rc7, v6.10-rc6, v6.10-rc5, v6.10-rc4, v6.10-rc3, v6.10-rc2, v6.10-rc1, v6.9, v6.9-rc7, v6.9-rc6, v6.9-rc5, v6.9-rc4, v6.9-rc3, v6.9-rc2, v6.9-rc1, v6.8, v6.8-rc7, v6.8-rc6, v6.8-rc5, v6.8-rc4, v6.8-rc3, v6.8-rc2, v6.8-rc1, v6.7, v6.7-rc8, v6.7-rc7, v6.7-rc6, v6.7-rc5, v6.7-rc4, v6.7-rc3, v6.7-rc2, v6.7-rc1, v6.6, v6.6-rc7, v6.6-rc6, v6.6-rc5, v6.6-rc4, v6.6-rc3, v6.6-rc2, v6.6-rc1, v6.5, v6.5-rc7, v6.5-rc6, v6.5-rc5, v6.5-rc4, v6.5-rc3, v6.5-rc2, v6.5-rc1, v6.4, v6.4-rc7, v6.4-rc6, v6.4-rc5, v6.4-rc4, v6.4-rc3, v6.4-rc2, v6.4-rc1, v6.3, v6.3-rc7, v6.3-rc6, v6.3-rc5, v6.3-rc4, v6.3-rc3, v6.3-rc2, v6.3-rc1, v6.2, v6.2-rc8, v6.2-rc7, v6.2-rc6, v6.2-rc5, v6.2-rc4, v6.2-rc3, v6.2-rc2, v6.2-rc1, v6.1, v6.1-rc8, v6.1-rc7, v6.1-rc6, v6.1-rc5, v6.1-rc4, v6.1-rc3, v6.1-rc2, v6.1-rc1, v6.0, v6.0-rc7, v6.0-rc6, v6.0-rc5, v6.0-rc4, v6.0-rc3, v6.0-rc2, v6.0-rc1, v5.19, v5.19-rc8, v5.19-rc7, v5.19-rc6, v5.19-rc5, v5.19-rc4, v5.19-rc3, v5.19-rc2, v5.19-rc1, v5.18, v5.18-rc7, v5.18-rc6, v5.18-rc5, v5.18-rc4, v5.18-rc3, v5.18-rc2, v5.18-rc1, v5.17, v5.17-rc8, v5.17-rc7, v5.17-rc6, v5.17-rc5, v5.17-rc4, v5.17-rc3, v5.17-rc2, v5.17-rc1, v5.16, v5.16-rc8, v5.16-rc7, v5.16-rc6, v5.16-rc5, v5.16-rc4, v5.16-rc3, v5.16-rc2, v5.16-rc1, v5.15, v5.15-rc7, v5.15-rc6, v5.15-rc5, v5.15-rc4, v5.15-rc3 |
| #
8d6e9098 |
| 24-Sep-2021 |
Steven Rostedt (VMware) <[email protected]> |
tracing: Create a sparse bitmask for pid filtering
When the trace_pid_list was created, the default pid max was 32768.
Creating a bitmask that can hold one bit for all 32768 took up 4096 (one
page).
tracing: Create a sparse bitmask for pid filtering
When the trace_pid_list was created, the default pid max was 32768.
Creating a bitmask that can hold one bit for all 32768 took up 4096 (one
page). Having a one page bitmask was not much of a problem, and that was
used for mapping pids. But today, systems are bigger and can run more
tasks, and now the default pid_max is usually set to 4194304. Which means
to handle that many pids requires 524288 bytes. Worse yet, the pid_max can
be set to 2^30 (1073741824 or 1G) which would take 134217728 (128M) of
memory to store this array.
Since the pid_list array is very sparsely populated, it is a huge waste of
memory to store all possible bits for each pid when most will not be set.
Instead, use a page table scheme to store the array, and allow this to
handle up to 30 bit pids.
The pid_mask will start out with 256 entries for the first 8 MSB bits.
This will cost 1K for 32 bit architectures and 2K for 64 bit. Each of
these will have a 256 array to store the next 8 bits of the pid (another
1 or 2K). These will hold an 2K byte bitmask (which will cover the LSB
14 bits or 16384 pids).
When the trace_pid_list is allocated, it will have the 1/2K upper bits
allocated, and then it will allocate a cache for the next upper chunks and
the lower chunks (default 6 of each). Then when a bit is "set", these
chunks will be pulled from the free list and added to the array. If the
free list gets down to a lever (default 2), it will trigger an irqwork
that will refill the cache back up.
On clearing a bit, if the clear causes the bitmask to be zero, that chunk
will then be placed back into the free cache for later use, keeping the
need to allocate more down to a minimum.
Signed-off-by: Steven Rostedt (VMware) <[email protected]>
show more ...
|