usb: typec: tcpci: Prevent Sink disconnection before vPpsShutdown in SPR PPS

The Source can drop its output voltage to the minimum of the requested
PPS APDO voltage range when it is in Current Limit

usb: typec: tcpci: Prevent Sink disconnection before vPpsShutdown in SPR PPS

The Source can drop its output voltage to the minimum of the requested
PPS APDO voltage range when it is in Current Limit Mode. If this voltage
falls within the range of vPpsShutdown, the Source initiates a Hard
Reset and discharges Vbus. However, currently the Sink may disconnect
before the voltage reaches vPpsShutdown, leading to unexpected behavior.

Prevent premature disconnection by setting the Sink's disconnect
threshold to the minimum vPpsShutdown value. Additionally, consider the
voltage drop due to IR drop when calculating the appropriate threshold.
This ensures a robust and reliable interaction between the Source and
Sink during SPR PPS Current Limit Mode operation.

Fixes: 4288debeaa4e ("usb: typec: tcpci: Fix up sink disconnect thresholds for PD")
Cc: stable <[email protected]>
Signed-off-by: Kyle Tso <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Reviewed-by: Badhri Jagan Sridharan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

usb: typec: tcpm: add support to set tcpc connector orientatition

This adds the support to set the connector orientation value
accordingly. This is part of the optional CONFIG_STANDARD_OUTPUT
regist

usb: typec: tcpm: add support to set tcpc connector orientatition

This adds the support to set the connector orientation value
accordingly. This is part of the optional CONFIG_STANDARD_OUTPUT
register 0x18, specified within the USB port controller spsicification
rev. 2.0 [1].

[1] https://www.usb.org/sites/default/files/documents/usb-port_controller_specification_rev2.0_v1.0_0.pdf

Signed-off-by: Marco Felsch <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

usb: typec: tcpci: add attempt_vconn_swap_discovery callback

Add attempt_vconn_swap_discovery callback to determine whether the TCPM
should perform a Vconn swap following Discover Identity on SOP. T

usb: typec: tcpci: add attempt_vconn_swap_discovery callback

Add attempt_vconn_swap_discovery callback to determine whether the TCPM
should perform a Vconn swap following Discover Identity on SOP. The tcpci
will return false unless chip level drivers implement the callback.

Maxim based TCPCs will return true unless the last connection resulted in
a Vconn Over Current Fault, which may be the result of the Vconn swap. In
addition to the port resetting, the TCPCI will veto the next Vconn swap
from occurring.

Signed-off-by: RD Babiera <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

usb: typec: tcpci: add tcpm_transmit_type to tcpm_pd_receive

tcpm_pd_receive adds the SOP type as a parameter, and passes it within the
pd_rx_event struct for tcpm_pd_rx_handler to use. For now, the

usb: typec: tcpci: add tcpm_transmit_type to tcpm_pd_receive

tcpm_pd_receive adds the SOP type as a parameter, and passes it within the
pd_rx_event struct for tcpm_pd_rx_handler to use. For now, the handler
drops all SOP' messages.

Maxim based tcpci drivers are capable of SOP' communication, so process_rx
now takes the SOP type into account and passes the value to
tcpm_pd_receive.

tcpci_set_pd_rx now utilizes the cable_comm_capable flag to determine if
TCPC_RX_DETECT_SOP1 should be added to the bitfield when enabling PD
message reception.

For all other consumers of tcpm_pd_receive, default the new field to
TCPC_TX_SOP.

Signed-off-by: RD Babiera <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

usb: typec: tcpci: add cable_comm_capable attribute

Add cable_comm_capable to tcpci_data for tcpci drivers to indicate that
the port tcpc is capable of communicating to cables over SOP. A
correspond

usb: typec: tcpci: add cable_comm_capable attribute

Add cable_comm_capable to tcpci_data for tcpci drivers to indicate that
the port tcpc is capable of communicating to cables over SOP. A
corresponding tcpci callback tcpci_cable_comm_capable returns this value.
The tcpm will primarily use this in later patches to determine if the port
can transmit and receive SOP' messages.

Maxim based tcpci drivers are capable of SOP' communication, so the
cable_comm_capable flag is set to true.

Signed-off-by: RD Babiera <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

usb: typec: tcpm: add tcpm_port_error_recovery symbol

Add tcpm_port_error_recovery symbol and corresponding event that runs in
tcpm_pd_event handler to set the port to the ERROR_RECOVERY state. tcpc

usb: typec: tcpm: add tcpm_port_error_recovery symbol

Add tcpm_port_error_recovery symbol and corresponding event that runs in
tcpm_pd_event handler to set the port to the ERROR_RECOVERY state. tcpci
drivers can use the symbol to reset the port when tcpc faults affect port
functionality.

Signed-off-by: RD Babiera <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Reviewed-by: Guenter Roeck <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

usb: typec: tcpm: Add callbacks to mitigate wakeups due to contaminant

On some of the TCPC implementations, when the Type-C port is exposed
to contaminants, such as water, TCPC stops toggling while

usb: typec: tcpm: Add callbacks to mitigate wakeups due to contaminant

On some of the TCPC implementations, when the Type-C port is exposed
to contaminants, such as water, TCPC stops toggling while reporting OPEN
either by the time TCPM reads CC pin status or during CC debounce
window. This causes TCPM to be stuck in TOGGLING state. If TCPM is made
to restart toggling, the behavior recurs causing redundant CPU wakeups
till the USB-C port is free of contaminant.

[206199.287817] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[206199.640337] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[206199.985789] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]

(or)

[ 7853.867577] Start toggling
[ 7853.889921] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[ 7855.698765] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected]
[ 7855.698790] state change TOGGLING -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[ 7855.698826] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[ 7855.703559] CC1: 0 -> 0, CC2: 5 -> 5 [state SNK_ATTACH_WAIT, polarity 0, connected]
[ 7855.856555] CC1: 0 -> 0, CC2: 5 -> 0 [state SNK_ATTACH_WAIT, polarity 0, disconnected]
[ 7855.856581] state change SNK_ATTACH_WAIT -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[ 7855.856613] pending state change SNK_ATTACH_WAIT -> SNK_UNATTACHED @ 170 ms [rev3 NONE_AMS]
[ 7856.027744] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [delayed 170 ms]
[ 7856.181949] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[ 7856.187896] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[ 7857.645630] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[ 7857.647291] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected]
[ 7857.647298] state change TOGGLING -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[ 7857.647310] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[ 7857.808106] CC1: 0 -> 0, CC2: 5 -> 0 [state SNK_ATTACH_WAIT, polarity 0, disconnected]
[ 7857.808123] state change SNK_ATTACH_WAIT -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[ 7857.808150] pending state change SNK_ATTACH_WAIT -> SNK_UNATTACHED @ 170 ms [rev3 NONE_AMS]
[ 7857.978727] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [delayed 170 ms]

To mitigate redundant TCPM wakeups, TCPCs which do have the needed hardware
can implement the check_contaminant callback which is invoked by TCPM
to evaluate for presence of contaminant. Lower level TCPC driver can
restart toggling through TCPM_PORT_CLEAN event when the driver detects
that USB-C port is free of contaminant. check_contaminant callback also
passes the disconnect_while_debounce flag which when true denotes that
the CC pins transitioned to OPEN state during the CC debounce window.

Signed-off-by: Badhri Jagan Sridharan <[email protected]>
Acked-by: Heikki Krogerus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

usb: typec: tcpm: Move TCPC to APPLY_RC state during PR_SWAP

When vbus auto discharge is enabled, TCPCI based TCPC transitions
into Attached.SNK/Attached.SRC state. During PR_SWAP, TCPCI based
TCPC

usb: typec: tcpm: Move TCPC to APPLY_RC state during PR_SWAP

When vbus auto discharge is enabled, TCPCI based TCPC transitions
into Attached.SNK/Attached.SRC state. During PR_SWAP, TCPCI based
TCPC would disconnect when partner changes power roles. TCPC has
to be moved APPLY RC state during PR_SWAP. This is done by
ROLE_CONTROL.CC1 != ROLE_CONTROL.CC2 and
POWER_CONTROL.AutodischargeDisconnect is 0. Once the swap sequence
is done, AutoDischargeDisconnect is re-enabled.

Fixes: f321a02caebd ("usb: typec: tcpm: Implement enabling Auto Discharge disconnect support")
Reviewed-by: Guenter Roeck <[email protected]>
Acked-by: Heikki Krogerus <[email protected]>
Signed-off-by: Badhri Jagan Sridharan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

usb: typec: tcpm: Add Callback to Usb Communication capable partner

The USB Communications Capable bit indicates if port
partner is capable of communication over the USB data lines
(e.g. D+/- or SS

usb: typec: tcpm: Add Callback to Usb Communication capable partner

The USB Communications Capable bit indicates if port
partner is capable of communication over the USB data lines
(e.g. D+/- or SS Tx/Rx). Notify the status of the bit to low
level drivers to perform chip specific operation.
For instance, low level driver enables USB switches on D+/D-
lines to set up data path when the bit is set.

Refactored from patch initially authored by
Kyle Tso <[email protected]>

Reviewed-by: Heikki Krogerus <[email protected]>
Reviewed-by: Guenter Roeck <[email protected]>
Signed-off-by: Badhri Jagan Sridharan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

usb: typec: tcpm: AMS and Collision Avoidance

This patch provides the implementation of Collision Avoidance introduced
in PD3.0. The start of each Atomic Message Sequence (AMS) initiated by
the port

usb: typec: tcpm: AMS and Collision Avoidance

This patch provides the implementation of Collision Avoidance introduced
in PD3.0. The start of each Atomic Message Sequence (AMS) initiated by
the port will be denied if the current AMS is not interruptible. The
Source port will set the CC to SinkTxNG if it is going to initiate an
AMS, and SinkTxOk otherwise. Meanwhile, any AMS initiated by a Sink port
will be denied in TCPM if the port partner (Source) sets SinkTxNG except
for HARD_RESET and SOFT_RESET.

Tested-by: Hans de Goede <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Signed-off-by: Kyle Tso <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

usb: typec: tcpm: Introduce vsafe0v for vbus

TCPM at present lacks the notion of VSAFE0V. There
are three vbus threshold levels that are critical to track:
a. vSafe5V - VBUS “5 volts” as def

usb: typec: tcpm: Introduce vsafe0v for vbus

TCPM at present lacks the notion of VSAFE0V. There
are three vbus threshold levels that are critical to track:
a. vSafe5V - VBUS “5 volts” as defined by the USB
PD specification.
b. vSinkDisconnect - Threshold used for transition from
Attached.SNK to Unattached.SNK.
c. vSafe0V - VBUS “0 volts” as defined by the USB
PD specification.

Tracking vSafe0V is crucial for entry into Try.SNK and
Attached.SRC and turning vbus back on by the source in
response to hard reset.

>From "4.5.2.2.8.2 Exiting from AttachWait.SRC State" section
in the Type-C spec:

"The port shall transition to Attached.SRC when VBUS is at
vSafe0V and the SRC.Rd state is detected on exactly one of
the CC1 or CC2 pins for at least tCCDebounce."

"A DRP that strongly prefers the Sink role may optionally
transition to Try.SNK instead of Attached.SRC when VBUS
is at vSafe0V and the SRC.Rd state is detected on exactly
one of the CC1 or CC2 pins for at least tCCDebounce."

>From "7.1.5 Response to Hard Resets" section in the PD spec:

"After establishing the vSafe0V voltage condition on VBUS,
the Source Shall wait tSrcRecover before re-applying VCONN
and restoring VBUS to vSafe5V."

vbus_present in the TCPM code tracks vSafe5V(vbus_present is true)
and vSinkDisconnect(vbus_present is false).

This change adds is_vbus_vsafe0v callback which when set makes
TCPM query for vSafe0V voltage level when needed.

Since not all TCPC controllers might have the capability
to report vSafe0V, TCPM assumes that vSafe0V is same as
vSinkDisconnect when is_vbus_vsafe0v callback is not set.
This allows TCPM to continue to support controllers which don't
have the support for reporting vSafe0V.

Introducing vSafe0V helps fix the failure reported at
"Step 15. CVS verifies PUT remains in AttachWait.SRC for 500ms"
of "TD 4.7.2 Try. SNK DRP Connect DRP Test" of
"Universal Serial Bus Type-C (USB Type-C) Functional Test
Specification Chapters 4 and 5". Here the compliance tester
intentionally maintains vbus at greater than vSafe0V and expects
the Product under test to stay in AttachWait.SRC till vbus drops
to vSafe0V.

Reviewed-by: Guenter Roeck <[email protected]>
Acked-by: Heikki Krogerus <[email protected]>
Signed-off-by: Badhri Jagan Sridharan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

usb: typec: tcpm: Pass down negotiated rev to update retry count

nRetryCount was updated from 3 to 2 between PD2.0 and PD3.0 spec.
nRetryCount in "Table 6-34 Counter parameters" of the PD 2.0
spec i

usb: typec: tcpm: Pass down negotiated rev to update retry count

nRetryCount was updated from 3 to 2 between PD2.0 and PD3.0 spec.
nRetryCount in "Table 6-34 Counter parameters" of the PD 2.0
spec is set to 3, whereas, nRetryCount in "Table 6-59 Counter
parameters" is set to 2.

Pass down negotiated rev in pd_transmit so that low level chip
drivers can update the retry count accordingly before attempting
packet transmission.

This helps in passing "TEST.PD.PORT.ALL.02" of the
"Power Delivery Merged" test suite which was initially failing
with "The UUT did not retransmit the message nReryCount times"

In fusb302 & tcpci drivers, by default the driver sets the retry
count to 3 (Default for PD 2.0). Update this to 2,
if the negotiated rev is PD 3.0.

In wcove, since the retry count is intentionally set to max, leaving
it as is.

Reviewed-by: Guenter Roeck <[email protected]>
Acked-by: Heikki Krogerus <[email protected]>
Signed-off-by: Badhri Jagan Sridharan <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

usb: typec: tcpm: Implement enabling Auto Discharge disconnect support

TCPCI spec allows TCPC hardware to autonomously discharge the vbus
capacitance upon disconnect. The expectation is that the TCP

usb: typec: tcpm: Implement enabling Auto Discharge disconnect support

TCPCI spec allows TCPC hardware to autonomously discharge the vbus
capacitance upon disconnect. The expectation is that the TCPM enables
AutoDischargeDisconnect while entering SNK/SRC_ATTACHED states. Hardware
then automously discharges vbus when the vbus falls below a certain
threshold i.e. VBUS_SINK_DISCONNECT_THRESHOLD.

Apart from enabling the vbus discharge circuit, AutoDischargeDisconnect
is also used a flag to move TCPCI based TCPC implementations into
Attached.Snk/Attached.Src state as mentioned in
Figure 4-15. TCPC State Diagram before a Connection of the
USB Type-C Port Controller Interface Specification.
In such TCPC implementations, setting AutoDischargeDisconnect would
prevent TCPC into entering "Connection_Invalid" state as well.

Signed-off-by: Badhri Jagan Sridharan <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

usb: typec: tcpm: frs sourcing vbus callback

During FRS hardware autonomously starts to source vbus. Provide
callback to perform chip specific operations.

Signed-off-by: Badhri Jagan Sridharan <bad

usb: typec: tcpm: frs sourcing vbus callback

During FRS hardware autonomously starts to source vbus. Provide
callback to perform chip specific operations.

Signed-off-by: Badhri Jagan Sridharan <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)

PD 3.0 spec defines a new mechanism for power role swap called
Fast role swap. This change enables TCPM to support FRS when
acting as sink.

usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)

PD 3.0 spec defines a new mechanism for power role swap called
Fast role swap. This change enables TCPM to support FRS when
acting as sink.

Once the explicit contract is negotiated, sink port is
expected to query the source port for sink caps to
determine whether the source is FRS capable.
Bits 23 & 24 of fixed pdo of the sink caps from the source, when
set, indicates the current needed by the source when fast role
swap is in progress(Implicit contract phasae). 0 indicates that
the source does not support Fast Role Swap.

Upon receiving the FRS signal from the source,
TCPC(TCPM_FRS_EVENT) informs TCPM to start the Fast role swap sequence.

1. TCPM sends FRS PD message: FR_SWAP_SEND
2. If response is not received within the expiry of
SenderResponseTimer, Error recovery is triggered.:
FR_SWAP_SEND_TIMEOUT
3. Upon receipt of the accept message, TCPM waits for
PSSourceOffTimer for PS_READY message from the partner:
FR_SWAP_SNK_SRC_NEW_SINK_READY.

TCPC is expected to autonomously turn on vbus once the FRS
signal is received and vbus voltage falls below vsafe5v within
tSrcFrSwap. This is different from traditional power role swap
where the vbus sourcing is turned on by TCPM.

4. By this time, TCPC most likely would have started to
source vbus, TCPM waits for tSrcFrSwap to see if the
lower level TCPC driver signals TCPM_SOURCING_VBUS event:
FR_SWAP_SNK_SRC_SOURCE_VBUS_APPLIED.
5. When TCPC signals sourcing vbus, TCPM sends PS_READY msg and
changes the CC pin from Rd to Rp. This is the end of fast
role swap sequence and TCPM initiates the sequnce to negotiate
explicit contract by transitioning into SRC_STARTUP after
SwapSrcStart.

The code is written based on the sequence described in "Figure 8-107:
Dual-role Port in Sink to Source Fast Role Swap State Diagram" of
USB Power Delivery Specification Revision 3.0, Version 1.2.

Signed-off-by: Badhri Jagan Sridharan <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

usb: typec: tcpm: Support bist test data mode for compliance

TCPM supports BIST carried mode. PD compliance tests require
BIST Test Data to be supported as well.

Introducing set_bist_data callback

usb: typec: tcpm: Support bist test data mode for compliance

TCPM supports BIST carried mode. PD compliance tests require
BIST Test Data to be supported as well.

Introducing set_bist_data callback to signal tcpc driver for
configuring the port controller hardware to enable/disable
BIST Test Data mode.

Signed-off-by: Badhri Jagan Sridharan <[email protected]>
Reviewed-by: Guenter Roeck <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

usb: typec: tcpm: Remove tcpc_config configuration mechanism

All configuration can and should be done through fwnodes instead of
through the tcpc_config struct and there are no existing users left o

usb: typec: tcpm: Remove tcpc_config configuration mechanism

All configuration can and should be done through fwnodes instead of
through the tcpc_config struct and there are no existing users left of
struct tcpc_config, so lets remove it.

Signed-off-by: Hans de Goede <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 157

Based on 3 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of th

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 157

Based on 3 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 1105 file(s).

Signed-off-by: Thomas Gleixner <[email protected]>
Reviewed-by: Allison Randal <[email protected]>
Reviewed-by: Richard Fontana <[email protected]>
Reviewed-by: Kate Stewart <[email protected]>
Cc: [email protected]
Link: https://lkml.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

usb: typec: tcpm: Notify the tcpc to start connection-detection for SRPs

Some tcpc device-drivers need to explicitly be told to watch for connection
events, otherwise the tcpc will not generate any

usb: typec: tcpm: Notify the tcpc to start connection-detection for SRPs

Some tcpc device-drivers need to explicitly be told to watch for connection
events, otherwise the tcpc will not generate any TCPM_CC_EVENTs and devices
being plugged into the Type-C port will not be noticed.

For dual-role ports tcpm_start_drp_toggling() is used to tell the tcpc to
watch for connection events. Sofar we lack a similar callback to the tcpc
for single-role ports. With some tcpc-s such as the fusb302 this means
no TCPM_CC_EVENTs will be generated when the port is configured as a
single-role port.

This commit renames start_drp_toggling to start_toggling and since the
device-properties are parsed by the tcpm-core, adds a port_type parameter
to the start_toggling callback so that the tcpc_dev driver knows the
port-type and can act accordingly when it starts toggling.

The new start_toggling callback now always gets called if defined, instead
of only being called for DRP ports.

To avoid this causing undesirable functional changes all existing
start_drp_toggling implementations are not only renamed to start_toggling,
but also get a port_type check added and return -EOPNOTSUPP when port_type
is not DRP.

Fixes: ea3b4d5523bc("usb: typec: fusb302: Resolve fixed power role ...")
Cc: Adam Thomson <[email protected]>
Signed-off-by: Hans de Goede <[email protected]>
Reviewed-by: Guenter Roeck <[email protected]>
Acked-by: Heikki Krogerus <[email protected]>
Tested-by: Adam Thomson <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

usb: typec: tcpm: Remove unused functions

tcpm_update_source_capabilities() and tcpm_update_sink_capabilities()
are not used anywhere, and I don't recall why I introduced those functions
in the firs

usb: typec: tcpm: Remove unused functions

tcpm_update_source_capabilities() and tcpm_update_sink_capabilities()
are not used anywhere, and I don't recall why I introduced those functions
in the first place. Effectively that means that we don't know if they even
work, or ever did. Lets remove them.

Reported-by: Kyle Tso <[email protected]>
Signed-off-by: Guenter Roeck <[email protected]>
Acked-by: Kyle Tso <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

usb: typec: tcpm: Do not disconnect link for self powered devices

During HARD_RESET the data link is disconnected.
For self powered device, the spec is advising against doing that.

>From USB_PD_R3_

usb: typec: tcpm: Do not disconnect link for self powered devices

During HARD_RESET the data link is disconnected.
For self powered device, the spec is advising against doing that.

>From USB_PD_R3_0
7.1.5 Response to Hard Resets
Device operation during and after a Hard Reset is defined as follows:
Self-powered devices Should Not disconnect from USB during a Hard Reset
(see Section 9.1.2).
Bus powered devices will disconnect from USB during a Hard Reset due to the
loss of their power source.

Tackle this by letting TCPM know whether the device is self or bus powered.

This overcomes unnecessary port disconnections from hard reset.
Also, speeds up the enumeration time when connected to Type-A ports.

Signed-off-by: Badhri Jagan Sridharan <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
---------
Version history:
V3:
Rebase on top of usb-next

V2:
Based on feedback from [email protected]
- self_powered added to the struct tcpm_port which is populated from
a. "connector" node of the device tree in tcpm_fw_get_caps()
b. "self_powered" node of the tcpc_config in tcpm_copy_caps

Based on feedbase from [email protected]
- Code was refactored
- SRC_HARD_RESET_VBUS_OFF sets the link state to false based
on self_powered flag

V1 located here:
https://lkml.org/lkml/2018/9/13/94
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

usb: typec: tcpm: Support for Alternate Modes

This adds more complete handling of VDMs and registration of
partner alternate modes, and introduces callbacks for
alternate mode operations.

Only DFP

usb: typec: tcpm: Support for Alternate Modes

This adds more complete handling of VDMs and registration of
partner alternate modes, and introduces callbacks for
alternate mode operations.

Only DFP role is supported for now.

Signed-off-by: Heikki Krogerus <[email protected]>
Tested-by: Hans de Goede <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

usb: typec: add fwnode to tcpc

Add fwnode handle to get the fwnode so we can get typec configs
it contains.

Suggested-by: Heikki Krogerus <[email protected]>
Reviewed-by: Heikki Kroge

usb: typec: add fwnode to tcpc

Add fwnode handle to get the fwnode so we can get typec configs
it contains.

Suggested-by: Heikki Krogerus <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Signed-off-by: Li Jun <[email protected]>
Reviewed-by: Guenter Roeck <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

typec: tcpm: Add core support for sink side PPS

This commit adds code to handle requesting of PPS APDOs. Switching
between standard PDOs and APDOs, and re-requesting an APDO to
modify operating volt

typec: tcpm: Add core support for sink side PPS

This commit adds code to handle requesting of PPS APDOs. Switching
between standard PDOs and APDOs, and re-requesting an APDO to
modify operating voltage/current will be triggered by an
external call into TCPM.

Signed-off-by: Adam Thomson <[email protected]>
Acked-by: Heikki Krogerus <[email protected]>
Reviewed-by: Guenter Roeck <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

usb: typec: tcpm: remove max_snk_mv/ma/mw

Since there is no user of max_snk_*, so we can remove them from tcpm.

Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Li Jun <[email protected]

usb: typec: tcpm: remove max_snk_mv/ma/mw

Since there is no user of max_snk_*, so we can remove them from tcpm.

Reviewed-by: Hans de Goede <[email protected]>
Signed-off-by: Li Jun <[email protected]>
Reviewed-by: Guenter Roeck <[email protected]>
Acked-by: Heikki Krogerus <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...