treewide: Add SPDX license identifier - Makefile/Kconfig

Add SPDX license identifiers to all Make/Kconfig files which:

- Have no license information of any form

These files fall under the project

treewide: Add SPDX license identifier - Makefile/Kconfig

Add SPDX license identifiers to all Make/Kconfig files which:

- Have no license information of any form

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

GPL-2.0-only

Signed-off-by: Thomas Gleixner <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

sh-pfc: Move driver from drivers/sh/ to drivers/pinctrl/

Signed-off-by: Laurent Pinchart <[email protected]>
Acked-by: Paul Mundt <[email protected]>
Acked-by: Linus Wallei

sh-pfc: Move driver from drivers/sh/ to drivers/pinctrl/

Signed-off-by: Laurent Pinchart <[email protected]>
Acked-by: Paul Mundt <[email protected]>
Acked-by: Linus Walleij <[email protected]>
Signed-off-by: Simon Horman <[email protected]>

show more ...

sh: pfc: Shuffle PFC support core.

This follows the intc/clk changes and shuffles the PFC support code under
its own directory. This will facilitate better code sharing, and allow us
to trim down th

sh: pfc: Shuffle PFC support core.

This follows the intc/clk changes and shuffles the PFC support code under
its own directory. This will facilitate better code sharing, and allow us
to trim down the exported interface by quite a margin.

Signed-off-by: Paul Mundt <[email protected]>

show more ...

sh: pfc: Make gpio chip support optional where possible.

This implements some Kconfig knobs for ensuring that the PFC gpio chip
can be disabled or built as a module in the cases where it's optional,

sh: pfc: Make gpio chip support optional where possible.

This implements some Kconfig knobs for ensuring that the PFC gpio chip
can be disabled or built as a module in the cases where it's optional, or
forcibly enabled in cases where it's not.

Signed-off-by: Paul Mundt <[email protected]>

show more ...

sh: intc: Split up the INTC code.

This splits up the sh intc core in to something more vaguely resembling
a subsystem. Most of the functionality was alread fairly well
compartmentalized, and there w

sh: intc: Split up the INTC code.

This splits up the sh intc core in to something more vaguely resembling
a subsystem. Most of the functionality was alread fairly well
compartmentalized, and there were only a handful of interdependencies
that needed to be resolved in the process.

This also serves as future-proofing for the genirq and sparseirq rework,
which will make some of the split out functionality wholly generic,
allowing things to be killed off in place with minimal migration pain.

Signed-off-by: Paul Mundt <[email protected]>

show more ...

sh: intc: Implement reverse mapping for IRQs to per-controller IDs.

This implements a scheme roughly analogous to the PowerPC virtual to
hardware IRQ mapping, which we use for IRQ to per-controller

sh: intc: Implement reverse mapping for IRQs to per-controller IDs.

This implements a scheme roughly analogous to the PowerPC virtual to
hardware IRQ mapping, which we use for IRQ to per-controller ID mapping.
This makes it possible for drivers to use the IDs directly for lookup
instead of hardcoding the vector.

The main motivation for this work is as a building block for dynamically
allocating virtual IRQs for demuxing INTC events sharing a single INTEVT
in addition to a common masking source.

Signed-off-by: Paul Mundt <[email protected]>

show more ...

sh: Support IRQ balancing for SH-X3 proto cores, too.

This adds in hardware IRQ auto-distribution support for SH-X3 proto CPUs,
following the SH7786 support.

Signed-off-by: Paul Mundt <lethal@linux

sh: Support IRQ balancing for SH-X3 proto cores, too.

This adds in hardware IRQ auto-distribution support for SH-X3 proto CPUs,
following the SH7786 support.

Signed-off-by: Paul Mundt <[email protected]>

show more ...

sh: intc: IRQ auto-distribution support.

This implements support for hardware-managed IRQ balancing as implemented
by SH-X3 cores (presently only hooked up for SH7786, but can probably be
carried ov

sh: intc: IRQ auto-distribution support.

This implements support for hardware-managed IRQ balancing as implemented
by SH-X3 cores (presently only hooked up for SH7786, but can probably be
carried over to other SH-X3 cores, too).

CPUs need to specify their distribution register along with the mask
definitions, as these follow the same format. Peripheral IRQs that don't
opt out of balancing will be automatically distributed at the whim of the
hardware block, while each CPU needs to verify whether it is handling the
IRQ or not, especially before clearing the mask.

Signed-off-by: Paul Mundt <[email protected]>

show more ...

sh: intc: userimask support.

This adds support for hardware-assisted userspace irq masking for
special priority levels. Due to the SR.IMASK interactivity, only some
platforms implement this in hardw

sh: intc: userimask support.

This adds support for hardware-assisted userspace irq masking for
special priority levels. Due to the SR.IMASK interactivity, only some
platforms implement this in hardware (including but not limited to
SH-4A interrupt controllers, and ARM-based SH-Mobile CPUs). Each CPU
needs to wire this up on its own, for now only SH7786 is wired up as an
example.

Signed-off-by: Paul Mundt <[email protected]>

show more ...