net: dsa: microchip: rename ksz8 series files

The first KSZ8 series implementation was done for a KSZ8795 device but
since several other KSZ8 devices have been added. Rename these files
to adhere to

net: dsa: microchip: rename ksz8 series files

The first KSZ8 series implementation was done for a KSZ8795 device but
since several other KSZ8 devices have been added. Rename these files
to adhere to the ksz8 naming convention as already used in most
functions and the existing ksz8.h; add an explanatory note.

Signed-off-by: Pieter Van Trappen <[email protected]>
Acked-by: Arun Ramadoss <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

net: dsa: microchip: add support for different DCB app configurations

Add DCB support to configure app trust sources and default port priority.

Following commands can be used for testing:
dcb apptr

net: dsa: microchip: add support for different DCB app configurations

Add DCB support to configure app trust sources and default port priority.

Following commands can be used for testing:
dcb apptrust set dev lan1 order pcp dscp
dcb app replace dev lan1 default-prio 3

Since it is not possible to configure DSCP-Prio mapping per port, this
patch provide only ability to read switch global dscp-prio mapping and
way to enable/disable app trust for DSCP.

Signed-off-by: Oleksij Rempel <[email protected]>
Acked-by: Arun Ramadoss <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

net: dsa: microchip: Add partial ACL support for ksz9477 switches

This patch adds partial Access Control List (ACL) support for the
ksz9477 family of switches. ACLs enable filtering of incoming laye

net: dsa: microchip: Add partial ACL support for ksz9477 switches

This patch adds partial Access Control List (ACL) support for the
ksz9477 family of switches. ACLs enable filtering of incoming layer 2
MAC, layer 3 IP, and layer 4 TCP/UDP packets on each port. They provide
additional capabilities for filtering routed network protocols and can
take precedence over other forwarding functions.

ACLs can filter ingress traffic based on header fields such as
source/destination MAC address, EtherType, IPv4 address, IPv4 protocol,
UDP/TCP ports, and TCP flags. The ACL is an ordered list of up to 16
access control rules programmed into the ACL Table. Each entry specifies
a set of matching conditions and action rules for controlling packet
forwarding and priority.

The ACL also implements a count function, generating an interrupt
instead of a forwarding action. It can be used as a watchdog timer or an
event counter. The ACL consists of three parts: matching rules, action
rules, and processing entries. Multiple match conditions can be either
AND'ed or OR'ed together.

This patch introduces support for a subset of the available ACL
functionality, specifically layer 2 matching and prioritization of
matched packets. For example:

tc qdisc add dev lan2 clsact
tc filter add dev lan2 ingress protocol 0x88f7 flower action skbedit prio 7

tc qdisc add dev lan1 clsact
tc filter add dev lan1 ingress protocol 0x88f7 flower action skbedit prio 7

The hardware offloading implementation was benchmarked against a
configuration without hardware offloading. This latter setup relied on a
software-based Linux bridge. No noticeable differences were observed
between the two configurations. Here is an example of software-based
test:

ip l s dev enu1u1 up
ip l s dev enu1u2 up
ip l s dev enu1u4 up
ethtool -A enu1u1 autoneg off rx off tx off
ethtool -A enu1u2 autoneg off rx off tx off
ethtool -A enu1u4 autoneg off rx off tx off
ip l a name br0 type bridge
ip l s dev br0 up
ip l s enu1u1 master br0
ip l s enu1u2 master br0
ip l s enu1u4 master br0

tc qdisc add dev enu1u1 root handle 1: ets strict 4 priomap 3 3 2 2 1 1 0 0
tc qdisc add dev enu1u4 root handle 1: ets strict 4 priomap 3 3 2 2 1 1 0 0
tc qdisc add dev enu1u2 root handle 1: ets strict 4 priomap 3 3 2 2 1 1 0 0

tc qdisc add dev enu1u1 clsact
tc filter add dev enu1u1 ingress protocol ipv4 flower action skbedit prio 7

tc qdisc add dev enu1u4 clsact
tc filter add dev enu1u4 ingress protocol ipv4 flower action skbedit prio 0

On a system attached to the port enu1u2 I run two iperf3 server
instances:
iperf3 -s -p 5210 &
iperf3 -s -p 5211 &

On systems attached to enu1u4 and enu1u1 I run:
iperf3 -u -c 172.17.0.1 -p 5210 -b100M -l1472 -t100
and
iperf3 -u -c 172.17.0.1 -p 5211 -b100M -l1472 -t100

As a result, IP traffic on port enu1u1 will be prioritized and take
precedence over IP traffic on port enu1u4

Signed-off-by: Oleksij Rempel <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

net: dsa: microchip: ptp: add the posix clock support

This patch implement routines (adjfine, adjtime, gettime and settime)
for manipulating the chip's PTP clock. It registers the ptp caps
to posix

net: dsa: microchip: ptp: add the posix clock support

This patch implement routines (adjfine, adjtime, gettime and settime)
for manipulating the chip's PTP clock. It registers the ptp caps
to posix clock register.

Signed-off-by: Christian Eggers <[email protected]>
Co-developed-by: Arun Ramadoss <[email protected]>
Signed-off-by: Arun Ramadoss <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]> # mostly api
Reviewed-by: Florian Fainelli <[email protected]>
Reviewed-by: Jacob Keller <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

net: dsa: microchip: add DSA support for microchip LAN937x

Basic DSA driver support for lan937x and the device will be
configured through SPI interface.
It adds the lan937x_dev_ops in ksz_common.c f

net: dsa: microchip: add DSA support for microchip LAN937x

Basic DSA driver support for lan937x and the device will be
configured through SPI interface.
It adds the lan937x_dev_ops in ksz_common.c file and tries to reuse the
functionality of ksz9477 series switch.

drivers/net/dsa/microchip/ path is already part of MAINTAINERS &
the new files come under this path. Hence no update needed to the
MAINTAINERS

Signed-off-by: Arun Ramadoss <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

net: dsa: microchip: common ksz_spi_probe for ksz switches

As of now, there are two spi probes, one ksz8795_spi.c and other
ksz9477_spi.c. This patch combines two files into single ksz_spi.c. The
di

net: dsa: microchip: common ksz_spi_probe for ksz switches

As of now, there are two spi probes, one ksz8795_spi.c and other
ksz9477_spi.c. This patch combines two files into single ksz_spi.c. The
difference between the two are regmap config and struct ksz8. The regmap
config is assigned based on the platform data. And struct ksz8 is left
untouched, as it is used only ksz8795.c. It can be used for all
other switches also in future.

Signed-off-by: Arun Ramadoss <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

net: dsa: microchip: common menuconfig for ksz series switch

This patch replaces the two different menuconfig for ksz9477 and ksz8795
to single ksz_common. so that it can be extended for the other s

net: dsa: microchip: common menuconfig for ksz series switch

This patch replaces the two different menuconfig for ksz9477 and ksz8795
to single ksz_common. so that it can be extended for the other switch
like lan937x. And removes the export_symbols for the extern functions in
the ksz_common.h.

Signed-off-by: Arun Ramadoss <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

net: dsa: microchip: Add Microchip KSZ8863 SMI based driver support

Add KSZ88X3 driver support. We add support for the KXZ88X3 three port
switches using the Microchip SMI Interface. They are support

net: dsa: microchip: Add Microchip KSZ8863 SMI based driver support

Add KSZ88X3 driver support. We add support for the KXZ88X3 three port
switches using the Microchip SMI Interface. They are supported using the
MDIO-Bitbang Interface.

Signed-off-by: Michael Grzeschik <[email protected]>
Signed-off-by: Oleksij Rempel <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

net: dsa: microchip: add KSZ9477 I2C driver

Add KSZ9477 I2C driver support. The code ksz9477.c and ksz_common.c are
used together to generate the I2C driver.

Signed-off-by: Tristram Ha <Tristram.H

net: dsa: microchip: add KSZ9477 I2C driver

Add KSZ9477 I2C driver support. The code ksz9477.c and ksz_common.c are
used together to generate the I2C driver.

Signed-off-by: Tristram Ha <[email protected]>
[[email protected]: bring up to date, use ksz_common regmap macros]
Signed-off-by: George McCollister <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

net: dsa: ksz: Add Microchip KSZ8795 DSA driver

Add Microchip KSZ8795 DSA driver.

Signed-off-by: Tristram Ha <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
Cc: Andrew Lunn <

net: dsa: ksz: Add Microchip KSZ8795 DSA driver

Add Microchip KSZ8795 DSA driver.

Signed-off-by: Tristram Ha <[email protected]>
Signed-off-by: Marek Vasut <[email protected]>
Cc: Andrew Lunn <[email protected]>
Cc: David S. Miller <[email protected]>
Cc: Florian Fainelli <[email protected]>
Cc: Tristram Ha <[email protected]>
Cc: Vivien Didelot <[email protected]>
Cc: Woojung Huh <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

treewide: Add SPDX license identifier - Makefile/Kconfig

Add SPDX license identifiers to all Make/Kconfig files which:

- Have no license information of any form

These files fall under the project

treewide: Add SPDX license identifier - Makefile/Kconfig

Add SPDX license identifiers to all Make/Kconfig files which:

- Have no license information of any form

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

GPL-2.0-only

Signed-off-by: Thomas Gleixner <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

net: dsa: microchip: break KSZ9477 DSA driver into two files

Break KSZ9477 DSA driver into two files in preparation to add more KSZ
switch drivers.
Add common functions in ksz_common.h so that other

net: dsa: microchip: break KSZ9477 DSA driver into two files

Break KSZ9477 DSA driver into two files in preparation to add more KSZ
switch drivers.
Add common functions in ksz_common.h so that other KSZ switch drivers
can access code in ksz_common.c.
Add ksz_spi.h for common functions used by KSZ switch SPI drivers.

Signed-off-by: Tristram Ha <[email protected]>
Reviewed-by: Woojung Huh <[email protected]>
Reviewed-by: Pavel Machek <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

net: dsa: microchip: rename ksz_spi.c to ksz9477_spi.c

Rename ksz_spi.c to ksz9477_spi.c and update Kconfig in preparation to add
more KSZ switch drivers.

Signed-off-by: Tristram Ha <Tristram.Ha@mi

net: dsa: microchip: rename ksz_spi.c to ksz9477_spi.c

Rename ksz_spi.c to ksz9477_spi.c and update Kconfig in preparation to add
more KSZ switch drivers.

Signed-off-by: Tristram Ha <[email protected]>
Reviewed-by: Woojung Huh <[email protected]>
Reviewed-by: Pavel Machek <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

dsa: add DSA switch driver for Microchip KSZ9477

The KSZ9477 is a fully integrated layer 2, managed, 7 ports GigE switch
with numerous advanced features. 5 ports incorporate 10/100/1000 Mbps PHYs.
T

dsa: add DSA switch driver for Microchip KSZ9477

The KSZ9477 is a fully integrated layer 2, managed, 7 ports GigE switch
with numerous advanced features. 5 ports incorporate 10/100/1000 Mbps PHYs.
The other 2 ports have interfaces that can be configured as SGMII, RGMII, MII
or RMII. Either of these may connect directly to a host processor or
to an external PHY. The SGMII port may interface to a fiber optic transceiver.

This driver currently supports vlan, fdb, mdb & mirror dsa switch operations.

Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Woojung Huh <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...