dsa: mt7530: Utilize REGMAP_IRQ for interrupt handling

Replace the custom IRQ chip handler and mask/unmask functions with
REGMAP_IRQ. This significantly simplifies the code and allows for the
remova

dsa: mt7530: Utilize REGMAP_IRQ for interrupt handling

Replace the custom IRQ chip handler and mask/unmask functions with
REGMAP_IRQ. This significantly simplifies the code and allows for the
removal of almost all interrupt-related functions from mt7530.c.

Tested on MT7988A built-in switch (MMIO) as well as MT7531AE IC (MDIO).

Signed-off-by: Daniel Golle <[email protected]>
Acked-by: Chester A. Unal <[email protected]>
Link: https://patch.msgid.link/221013c3530b61504599e285c341a993f6188f00.1740792674.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <[email protected]>

show more ...

net: dsa: vsc73xx: Implement the tag_8021q VLAN operations

This patch is a simple implementation of 802.1q tagging in the vsc73xx
driver. Currently, devices with DSA_TAG_PROTO_NONE are not functiona

net: dsa: vsc73xx: Implement the tag_8021q VLAN operations

This patch is a simple implementation of 802.1q tagging in the vsc73xx
driver. Currently, devices with DSA_TAG_PROTO_NONE are not functional.
The VSC73XX family doesn't provide any tag support for external Ethernet
ports.

The only option available is VLAN-based tagging, which requires constant
hardware VLAN filtering. While the VSC73XX family supports provider
bridging, it only supports QinQ without full implementation of 802.1AD.
This means it only allows the doubled 0x8100 TPID.

In the simple port mode, QinQ is enabled to preserve forwarding of
VLAN-tagged frames.

Signed-off-by: Pawel Dembicki <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Link: https://patch.msgid.link/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>

show more ...

net: dsa: lan9303: imply SMSC_PHY

Both LAN9303 and LAN9354 have internal PHYs on both external ports.
Therefore a configuration without SMSC PHY support is non-practical at
least and leads to:

LAN9

net: dsa: lan9303: imply SMSC_PHY

Both LAN9303 and LAN9354 have internal PHYs on both external ports.
Therefore a configuration without SMSC PHY support is non-practical at
least and leads to:

LAN9303_MDIO 8000f00.mdio:00: Found LAN9303 rev. 1
mdio_bus 8000f00.mdio:00: deferred probe pending: (reason unknown)

Signed-off-by: Alexander Sverdlin <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>

show more ...

net: dsa: mt7530: select MEDIATEK_GE_PHY for NET_DSA_MT7530_MDIO

Quoting from commit 4223f8651287 ("net: dsa: mt7530: make NET_DSA_MT7530
select MEDIATEK_GE_PHY"):

Make MediaTek MT753x DSA driver e

net: dsa: mt7530: select MEDIATEK_GE_PHY for NET_DSA_MT7530_MDIO

Quoting from commit 4223f8651287 ("net: dsa: mt7530: make NET_DSA_MT7530
select MEDIATEK_GE_PHY"):

Make MediaTek MT753x DSA driver enable MediaTek Gigabit PHYs driver to
properly control MT7530 and MT7531 switch PHYs.

A noticeable change is that the behaviour of switchport interfaces going
up-down-up-down is no longer there.

Now, the switch can be used without the PHYs but, at the moment, every
hardware design out there that I have seen uses them. For that, it would
make the most sense to force the selection of MEDIATEK_GE_PHY for the MDIO
interface which currently controls the MT7530 and MT7531 switches.

Signed-off-by: Arınç ÜNAL <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>

show more ...

net: dsa: mt7530: improve and relax PHY driver dependency

Different MT7530 variants require different PHY drivers.
Use 'imply' instead of 'select' to relax the dependency on the PHY
driver, and choo

net: dsa: mt7530: improve and relax PHY driver dependency

Different MT7530 variants require different PHY drivers.
Use 'imply' instead of 'select' to relax the dependency on the PHY
driver, and choose the appropriate driver.

Signed-off-by: Daniel Golle <[email protected]>
Reviewed-by: Simon Horman <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

net: dsa: mt7530: introduce driver for MT7988 built-in switch

Add driver for the built-in Gigabit Ethernet switch which can be found
in the MediaTek MT7988 SoC.

The switch shares most of its design

net: dsa: mt7530: introduce driver for MT7988 built-in switch

Add driver for the built-in Gigabit Ethernet switch which can be found
in the MediaTek MT7988 SoC.

The switch shares most of its design with MT7530 and MT7531, but has
it's registers mapped into the SoCs register space rather than being
connected externally or internally via MDIO.

Introduce a new platform driver to support that.

Signed-off-by: Daniel Golle <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

net: dsa: mt7530: introduce separate MDIO driver

Split MT7530 switch driver into a common part and a part specific
for MDIO connected switches and multi-chip modules.
Move MDIO-specific functions to

net: dsa: mt7530: introduce separate MDIO driver

Split MT7530 switch driver into a common part and a part specific
for MDIO connected switches and multi-chip modules.
Move MDIO-specific functions to newly introduced mt7530-mdio.c while
keeping the common parts in mt7530.c.
Introduce new Kconfig symbol CONFIG_NET_DSA_MT7530_MDIO which is
implied by CONFIG_NET_DSA_MT7530.

Signed-off-by: Daniel Golle <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

net: dsa: mt7530: use external PCS driver

Implement regmap access wrappers, for now only to be used by the
pcs-mtk-lynxi driver.
Make use of this external PCS driver and drop the now reduntant
imple

net: dsa: mt7530: use external PCS driver

Implement regmap access wrappers, for now only to be used by the
pcs-mtk-lynxi driver.
Make use of this external PCS driver and drop the now reduntant
implementation in mt7530.c.
As a nice side effect the SGMII registers can now also more easily be
inspected for debugging via /sys/kernel/debug/regmap.

Tested-by: Bjørn Mork <[email protected]>
Signed-off-by: Daniel Golle <[email protected]>
Tested-by: Frank Wunderlich <[email protected]>
Reviewed-by: Russell King (Oracle) <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>

show more ...

net: dsa: mt7530: fix tristate and help description

Fix description for tristate and help sections which include inaccurate
information.

Signed-off-by: Arınç ÜNAL <[email protected]>
Link: http

net: dsa: mt7530: fix tristate and help description

Fix description for tristate and help sections which include inaccurate
information.

Signed-off-by: Arınç ÜNAL <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>

show more ...

net: dsa: modularize DSA_TAG_PROTO_NONE

There is no reason that I can see why the no-op tagging protocol should
be registered manually, so make it a module and make all drivers which
have any sort o

net: dsa: modularize DSA_TAG_PROTO_NONE

There is no reason that I can see why the no-op tagging protocol should
be registered manually, so make it a module and make all drivers which
have any sort of reference to DSA_TAG_PROTO_NONE select it.

Note that I don't know if ksz_get_tag_protocol() really needs this,
or if it's just the logic which is poorly written. All switches seem to
have their own tagging protocol, and DSA_TAG_PROTO_NONE is just a
fallback that never gets used.

Signed-off-by: Vladimir Oltean <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>

show more ...

net: dsa: LAN9303: Add basic support for LAN9354

Adding support for the LAN9354 device by allowing it to use
the LAN9303 DSA driver. These devices have the same underlying
access and control method

net: dsa: LAN9303: Add basic support for LAN9354

Adding support for the LAN9354 device by allowing it to use
the LAN9303 DSA driver. These devices have the same underlying
access and control methods and from a feature set point of view
the LAN9354 is a superset of the LAN9303.

The MDIO access method has been tested on a SAMA5D3-EDS board
with a LAN9354 RMII daughter card.

While the SPI access method should also be the same, it has not
been tested and as such is not included at this time.

Signed-off-by: Jerry Ray <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

net: dsa: qca8k: move driver to qca dir

Move qca8k driver to qca dir in preparation for code split and
introduction of ipq4019 switch based on qca8k.

Signed-off-by: Christian Marangi <ansuelsmth@gm

net: dsa: qca8k: move driver to qca dir

Move qca8k driver to qca dir in preparation for code split and
introduction of ipq4019 switch based on qca8k.

Signed-off-by: Christian Marangi <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver

Add Renesas RZ/N1 advanced 5 port switch driver. This switch handles 5
ports including 1 CPU management port. A MDIO bus is also

net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver

Add Renesas RZ/N1 advanced 5 port switch driver. This switch handles 5
ports including 1 CPU management port. A MDIO bus is also exposed by
this switch and allows to communicate with PHYs connected to the ports.
Each switch port (except for the CPU management ports) is connected to
the MII converter.

This driver includes basic bridging support, more support will be added
later (vlan, etc).

Suggested-by: Jean-Pierre Geslin <[email protected]>
Suggested-by: Phil Edworthy <[email protected]>
Signed-off-by: Clément Léger <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

net: dsa: restrict SMSC_LAN9303_I2C kconfig

Since kconfig 'select' does not follow dependency chains, if symbol KSA
selects KSB, then KSA should also depend on the same symbols that KSB
depends on,

net: dsa: restrict SMSC_LAN9303_I2C kconfig

Since kconfig 'select' does not follow dependency chains, if symbol KSA
selects KSB, then KSA should also depend on the same symbols that KSB
depends on, in order to prevent Kconfig warnings and possible build
errors.

Change NET_DSA_SMSC_LAN9303_I2C and NET_DSA_SMSC_LAN9303_MDIO so that
they are limited to VLAN_8021Q if the latter is enabled. This prevents
the Kconfig warning:

WARNING: unmet direct dependencies detected for NET_DSA_SMSC_LAN9303
Depends on [m]: NETDEVICES [=y] && NET_DSA [=y] && (VLAN_8021Q [=m] || VLAN_8021Q [=m]=n)
Selected by [y]:
- NET_DSA_SMSC_LAN9303_I2C [=y] && NETDEVICES [=y] && NET_DSA [=y] && I2C [=y]

Fixes: 430065e26719 ("net: dsa: lan9303: add VLAN IDs to master device")
Signed-off-by: Randy Dunlap <[email protected]>
Cc: Andrew Lunn <[email protected]>
Cc: Vivien Didelot <[email protected]>
Cc: Florian Fainelli <[email protected]>
Cc: Vladimir Oltean <[email protected]>
Cc: Juergen Borleis <[email protected]>
Cc: "David S. Miller" <[email protected]>
Cc: Eric Dumazet <[email protected]>
Cc: Jakub Kicinski <[email protected]>
Cc: Paolo Abeni <[email protected]>
Cc: Mans Rullgard <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

net: dsa: lan9303: add VLAN IDs to master device

If the master device does VLAN filtering, the IDs used by the switch
must be added for any frames to be received. Do this in the
port_enable() funct

net: dsa: lan9303: add VLAN IDs to master device

If the master device does VLAN filtering, the IDs used by the switch
must be added for any frames to be received. Do this in the
port_enable() function, and remove them in port_disable().

Fixes: a1292595e006 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Mans Rullgard <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>

show more ...

net: dsa: mt7530: make NET_DSA_MT7530 select MEDIATEK_GE_PHY

Make MediaTek MT753x DSA driver enable MediaTek Gigabit PHYs driver to
properly control MT7530 and MT7531 switch PHYs.

A noticeable chan

net: dsa: mt7530: make NET_DSA_MT7530 select MEDIATEK_GE_PHY

Make MediaTek MT753x DSA driver enable MediaTek Gigabit PHYs driver to
properly control MT7530 and MT7531 switch PHYs.

A noticeable change is that the behaviour of switchport interfaces going
up-down-up-down is no longer there.

Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Arınç ÜNAL <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Jakub Kicinski <[email protected]>

show more ...

net: dsa: realtek-smi: move to subdirectory

Signed-off-by: Luiz Angelo Daros de Luca <[email protected]>
Tested-by: Arınç ÜNAL <[email protected]>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.

net: dsa: realtek-smi: move to subdirectory

Signed-off-by: Luiz Angelo Daros de Luca <[email protected]>
Tested-by: Arınç ÜNAL <[email protected]>
Reviewed-by: Alvin Šipraga <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC

This patch adds a realtek-smi subdriver for the RTL8365MB-VC 4+1 port
10/100/1000M switch controller. The driver has been developed ba

net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC

This patch adds a realtek-smi subdriver for the RTL8365MB-VC 4+1 port
10/100/1000M switch controller. The driver has been developed based on a
GPL-licensed OS-agnostic Realtek vendor driver known as rtl8367c found
in the OpenWrt source tree.

Despite the name, the RTL8365MB-VC has an entirely different register
layout to the already-supported RTL8366RB ASIC. Notwithstanding this,
the structure of the rtl8365mb subdriver is loosely based on the rtl8366rb
subdriver. Like the 'rb, it establishes its own irqchip to handle
cascaded PHY link status interrupts.

The RTL8365MB-VC switch is capable of offloading a large number of
features from the software, but this patch introduces only the most
basic DSA driver functionality. The ports always function as standalone
ports, with bridging handled in software.

One more thing. Realtek's nomenclature for switches makes it hard to
know exactly what other ASICs might be supported by this driver. The
vendor driver goes by the name rtl8367c, but as far as I can tell, no
chip actually exists under this name. As such, the subdriver is named
rtl8365mb to emphasize the potentially limited support. But it is clear
from the vendor sources that a number of other more advanced switches
share a similar register layout, and further support should not be too
hard to add given access to the relevant hardware. With this in mind,
the subdriver has been written with as few assumptions about the
particular chip as is reasonable. But the RTL8365MB-VC is the only
hardware I have available, so some further work is surely needed.

Co-developed-by: Michael Rasmussen <[email protected]>
Signed-off-by: Michael Rasmussen <[email protected]>
Signed-off-by: Alvin Šipraga <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Tested-by: Arınç ÜNAL <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

dsa: simplify Kconfig symbols and dependencies

1. Remove CONFIG_HAVE_NET_DSA.

CONFIG_HAVE_NET_DSA is a legacy leftover from the times when drivers
should have selected CONFIG_NET_DSA manually.
Curr

dsa: simplify Kconfig symbols and dependencies

1. Remove CONFIG_HAVE_NET_DSA.

CONFIG_HAVE_NET_DSA is a legacy leftover from the times when drivers
should have selected CONFIG_NET_DSA manually.
Currently, all drivers has explicit 'depends on NET_DSA', so this is
no more needed.

2. CONFIG_HAVE_NET_DSA dependencies became CONFIG_NET_DSA's ones.

- dropped !S390 dependency which was introduced to be sure NET_DSA
can select CONFIG_PHYLIB. DSA migrated to Phylink almost 3 years
ago and the PHY library itself doesn't depend on !S390 since
commit 870a2b5e4fcd ("phylib: remove !S390 dependeny from Kconfig");
- INET dependency is kept to be sure we can select NET_SWITCHDEV;
- NETDEVICES dependency is kept to be sure we can select PHYLINK.

3. DSA drivers menu now depends on NET_DSA.

Instead on 'depends on NET_DSA' on every single driver, the entire
menu now depends on it. This eliminates a lot of duplicated lines
from Kconfig with no loss (when CONFIG_NET_DSA=m, drivers also can
be only m or n).
This also has a nice side effect that there's no more empty menu on
configurations without DSA.

4. Kbuild will now descend into 'drivers/net/dsa' only when
CONFIG_NET_DSA is y or m.

This is safe since no objects inside this folder can be built without
DSA core, as well as when CONFIG_NET_DSA=m, no objects can be
built-in.

Signed-off-by: Alexander Lobakin <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

net: dsa: add Arrow SpeedChips XRS700x driver

Add a driver with initial support for the Arrow SpeedChips XRS7000
series of gigabit Ethernet switch chips which are typically used in
critical networki

net: dsa: add Arrow SpeedChips XRS700x driver

Add a driver with initial support for the Arrow SpeedChips XRS7000
series of gigabit Ethernet switch chips which are typically used in
critical networking applications.

The switches have up to three RGMII ports and one RMII port.
Management to the switches can be performed over i2c or mdio.

Support for advanced features such as PTP and
HSR/PRP (IEC 62439-3 Clause 5 & 4) is not included in this patch and
may be added at a later date.

Signed-off-by: George McCollister <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>

show more ...

net: dsa: Add DSA driver for Hirschmann Hellcreek switches

Add a basic DSA driver for Hirschmann Hellcreek switches. Those switches are
implementing features needed for Time Sensitive Networking (TS

net: dsa: Add DSA driver for Hirschmann Hellcreek switches

Add a basic DSA driver for Hirschmann Hellcreek switches. Those switches are
implementing features needed for Time Sensitive Networking (TSN) such as support
for the Time Precision Protocol and various shapers like the Time Aware Shaper.

This driver includes basic support for networking:

* VLAN handling
* FDB handling
* Port statistics
* STP
* Phylink

Signed-off-by: Kurt Kanzenbach <[email protected]>
Reviewed-by: Vladimir Oltean <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Jakub Kicinski <[email protected]>

show more ...

net: dsa: mt7530: Add the support of MT7531 switch

Add new support for MT7531:

MT7531 is the next generation of MT7530. It is also a 7-ports switch with
5 giga embedded phys, 2 cpu ports, and the s

net: dsa: mt7530: Add the support of MT7531 switch

Add new support for MT7531:

MT7531 is the next generation of MT7530. It is also a 7-ports switch with
5 giga embedded phys, 2 cpu ports, and the same MAC logic of MT7530. Cpu
port 6 only supports SGMII interface. Cpu port 5 supports either RGMII
or SGMII in different HW sku, but cannot be muxed to PHY of port 0/4 like
mt7530. Due to SGMII interface support, pll, and pad setting are different
from MT7530. This patch adds different initial setting, and SGMII phylink
handlers of MT7531.

MT7531 SGMII interface can be configured in following mode:
- 'SGMII AN mode' with in-band negotiation capability
which is compatible with PHY_INTERFACE_MODE_SGMII.
- 'SGMII force mode' without in-band negotiation
which is compatible with 10B/8B encoding of
PHY_INTERFACE_MODE_1000BASEX with fixed full-duplex and fixed pause.
- 2.5 times faster clocked 'SGMII force mode' without in-band negotiation
which is compatible with 10B/8B encoding of
PHY_INTERFACE_MODE_2500BASEX with fixed full-duplex and fixed pause.

Signed-off-by: Landen Chao <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

net: dsa: mt7530: Refine message in Kconfig

Refine message in Kconfig with fixing typo and an explicit MT7621 support.

Signed-off-by: Landen Chao <[email protected]>
Signed-off-by: Sean Wang

net: dsa: mt7530: Refine message in Kconfig

Refine message in Kconfig with fixing typo and an explicit MT7621 support.

Signed-off-by: Landen Chao <[email protected]>
Signed-off-by: Sean Wang <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

net: dsa: rtl8366rb: Support the CPU DSA tag

This activates the support to use the CPU tag to properly
direct ingress traffic to the right port.

Bit 15 in register RTL8368RB_CPU_CTRL_REG can be set

net: dsa: rtl8366rb: Support the CPU DSA tag

This activates the support to use the CPU tag to properly
direct ingress traffic to the right port.

Bit 15 in register RTL8368RB_CPU_CTRL_REG can be set to
1 to disable the insertion of the CPU tag which is what
the code currently does. The bit 15 define calls this
setting RTL8368RB_CPU_INSTAG which is confusing since the
inverse meaning is implied: programmers may think that
setting this bit to 1 will *enable* inserting the tag
rather than disabling it, so rename this setting in
bit 15 to RTL8368RB_CPU_NO_TAG which is more to the
point.

After this e.g. ping works out-of-the-box with the
RTL8366RB.

Cc: DENG Qingfang <[email protected]>
Cc: Mauri Sandberg <[email protected]>
Reviewed-by: Andrew Lunn <[email protected]>
Reviewed-by: Florian Fainelli <[email protected]>
Signed-off-by: Linus Walleij <[email protected]>
Signed-off-by: David S. Miller <[email protected]>

show more ...

treewide: replace '---help---' in Kconfig files with 'help'

Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasi

treewide: replace '---help---' in Kconfig files with 'help'

Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.

This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.

There are a variety of indentation styles found.

a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'

In order to convert all of them to 1 tab + 'help', I ran the
following commend:

$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'

Signed-off-by: Masahiro Yamada <[email protected]>

show more ...