can: Kconfig: add CONFIG_CAN_RX_OFFLOAD

Only a few drivers rely on the CAN rx offload framework (as of the
writing of this patch, only four: flexcan, m_can, mcp251xfd and
ti_hecc). Split it out of c

can: Kconfig: add CONFIG_CAN_RX_OFFLOAD

Only a few drivers rely on the CAN rx offload framework (as of the
writing of this patch, only four: flexcan, m_can, mcp251xfd and
ti_hecc). Split it out of can-dev and add a new config symbol:
CAN_RX_OFFLOAD.

The drivers relying on CAN rx offload are in different sub
folders. Make CAN_RX_OFFLOAD an hidden option and tag all the drivers
depending on that feature with "select CAN_RX_OFFLOAD" so that the
option gets automatically enabled if and only if one of those drivers
is chosen.

Link: https://lore.kernel.org/all/[email protected]
Suggested-by: Geert Uytterhoeven <[email protected]>
Suggested-by: Jakub Kicinski <[email protected]>
Signed-off-by: Vincent Mailhol <[email protected]>
Acked-by: Max Staudt <[email protected]>
Tested-by: Oliver Hartkopp <[email protected]>
Signed-off-by: Marc Kleine-Budde <[email protected]>

show more ...

can: m_can: add PCI glue driver for Intel Elkhart Lake

Add support for M_CAN controller on Intel Elkhart Lake attached to the PCI bus.
It integrates the Bosch M_CAN controller with Message RAM and t

can: m_can: add PCI glue driver for Intel Elkhart Lake

Add support for M_CAN controller on Intel Elkhart Lake attached to the PCI bus.
It integrates the Bosch M_CAN controller with Message RAM and the wrapper IP
block with additional registers which all of them are within the same MMIO
range.

Currently only interrupt control register from wrapper IP is used and the MRAM
configuration is expected to come from the firmware via "bosch,mram-cfg" device
property and parsed by m_can.c core.

Initial implementation is done by Felipe Balbi while he was working at Intel
with later changes from Raymond Tan and me.

Co-developed-by: Felipe Balbi (Intel) <[email protected]>
Co-developed-by: Raymond Tan <[email protected]>
Signed-off-by: Felipe Balbi (Intel) <[email protected]>
Signed-off-by: Raymond Tan <[email protected]>
Signed-off-by: Jarkko Nikula <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>

show more ...

can: m_can: Kconfig: convert the into menu

Since there is more than one base driver for the m_can core, let's
convert this into a menu.

Link: https://lore.kernel.org/r/20201130133713.269256-4-mkl@p

can: m_can: Kconfig: convert the into menu

Since there is more than one base driver for the m_can core, let's
convert this into a menu.

Link: https://lore.kernel.org/r/[email protected]
Reviewed-by: Dan Murphy <[email protected]>
Signed-off-by: Marc Kleine-Budde <[email protected]>

show more ...

can: tcan4x5x: replace depends on REGMAP_SPI with depends on SPI

regmap is a library function that gets selected by drivers that need it. No
driver modules should depend on it. Instead depends on SP

can: tcan4x5x: replace depends on REGMAP_SPI with depends on SPI

regmap is a library function that gets selected by drivers that need it. No
driver modules should depend on it. Instead depends on SPI and select
REGMAP_SPI. Depending on REGMAP_SPI makes this driver only build if another
driver already selected REGMAP_SPI, as the symbol can't be selected through the
menu kernel configuration.

Signed-off-by: Enric Balletbo i Serra <[email protected]>
Link: http://lore.kernel.org/r/[email protected]
Reviewed-by: Dan Murphy <[email protected]>
Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Signed-off-by: Marc Kleine-Budde <[email protected]>

show more ...

can: drivers: fix spelling mistakes

This patch fixes spelling erros found by "codespell" in the
drivers/net/can subtree.

Link: https://lore.kernel.org/r/[email protected]

can: drivers: fix spelling mistakes

This patch fixes spelling erros found by "codespell" in the
drivers/net/can subtree.

Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Marc Kleine-Budde <[email protected]>

show more ...

treewide: replace '---help---' in Kconfig files with 'help'

Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasi

treewide: replace '---help---' in Kconfig files with 'help'

Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.

This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.

There are a variety of indentation styles found.

a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'

In order to convert all of them to 1 tab + 'help', I ran the
following commend:

$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'

Signed-off-by: Masahiro Yamada <[email protected]>

show more ...

can: tcan4x5x: Add tcan4x5x driver to the kernel

Add the TCAN4x5x SPI CAN driver.

This device uses the Bosch MCAN IP core along with a SPI interface map.
Register to the MCAN common core code to ma

can: tcan4x5x: Add tcan4x5x driver to the kernel

Add the TCAN4x5x SPI CAN driver.

This device uses the Bosch MCAN IP core along with a SPI interface map.
Register to the MCAN common core code to manage the MCAN IP.

This device has a special method to indicate a write/read operation on
the data payload.

Acked-by: Wolfgang Grandegger <[email protected]>
Signed-off-by: Dan Murphy <[email protected]>
Signed-off-by: Marc Kleine-Budde <[email protected]>

show more ...

can: m_can: Create a m_can platform framework

Create a m_can platform framework that peripheral
devices can register to and use common code and register sets.
The peripheral devices may provide read

can: m_can: Create a m_can platform framework

Create a m_can platform framework that peripheral
devices can register to and use common code and register sets.
The peripheral devices may provide read/write and configuration
support of the IP.

Acked-by: Wolfgang Grandegger <[email protected]>
Signed-off-by: Dan Murphy <[email protected]>
Acked-by: Faiz Abbas <[email protected]>
Signed-off-by: Marc Kleine-Budde <[email protected]>

show more ...

treewide: Add SPDX license identifier - Makefile/Kconfig

Add SPDX license identifiers to all Make/Kconfig files which:

- Have no license information of any form

These files fall under the project

treewide: Add SPDX license identifier - Makefile/Kconfig

Add SPDX license identifiers to all Make/Kconfig files which:

- Have no license information of any form

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

GPL-2.0-only

Signed-off-by: Thomas Gleixner <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

can: m_can: add CONFIG_HAS_IOMEM dependence

m_can uses io memory which makes it not compilable on architectures
without HAS_IOMEM such as UML:

drivers/built-in.o: In function `m_can_plat_probe':
m_

can: m_can: add CONFIG_HAS_IOMEM dependence

m_can uses io memory which makes it not compilable on architectures
without HAS_IOMEM such as UML:

drivers/built-in.o: In function `m_can_plat_probe':
m_can.c:(.text+0x218cc5): undefined reference to `devm_ioremap_resource'
m_can.c:(.text+0x218df9): undefined reference to `devm_ioremap'

Signed-off-by: David Cohen <[email protected]>
Signed-off-by: Marc Kleine-Budde <[email protected]>

show more ...

can: m_can: add Bosch M_CAN controller support

The patch adds the basic CAN TX/RX function support for Bosch M_CAN controller.
For TX, only one dedicated tx buffer is used for sending data.
For RX,

can: m_can: add Bosch M_CAN controller support

The patch adds the basic CAN TX/RX function support for Bosch M_CAN controller.
For TX, only one dedicated tx buffer is used for sending data.
For RX, RXFIFO 0 is used for receiving data to avoid overflow.
Rx FIFO 1 and Rx Buffers are not used currently, as well as Tx Event FIFO.

Due to the message ram can be shared by multi m_can instances
and the fifo element is configurable which is SoC dependant,
the design is to parse the message ram related configuration data from device
tree rather than hardcode define it in driver which can make the message
ram sharing fully transparent to M_CAN controller driver,
then we can gain better driver maintainability and future features upgrade.

M_CAN also supports CANFD protocol features like data payload up to 64 bytes
and bitrate switch at runtime, however, this patch still does not add the
support for these features.

Cc: Wolfgang Grandegger <[email protected]>
Cc: Marc Kleine-Budde <[email protected]>
Cc: Mark Rutland <[email protected]>
Cc: Oliver Hartkopp <[email protected]>
Cc: Varka Bhadram <[email protected]>
Signed-off-by: Dong Aisheng <[email protected]>
Reviewed-by: Varka Bhadram <[email protected]>
Signed-off-by: Fengguang Wu <[email protected]>
[mkl: Squahed semicolon cleanup by Fengguang Wu]
Signed-off-by: Marc Kleine-Budde <[email protected]>

show more ...