firmware: thead: Add AON firmware protocol driver

The T-Head TH1520 SoC uses an E902 co-processor running Always-On (AON)
firmware to manage power, clock, and other system resources [1]. This
patch

firmware: thead: Add AON firmware protocol driver

The T-Head TH1520 SoC uses an E902 co-processor running Always-On (AON)
firmware to manage power, clock, and other system resources [1]. This
patch introduces a driver implementing the AON firmware protocol,
allowing the Linux kernel to communicate with the firmware via mailbox
channels. Through an RPC-based interface, the kernel can initiate power
state transitions, update resource configurations, and perform other
AON-related tasks.

[1]
Link: https://openbeagle.org/beaglev-ahead/beaglev-ahead/-/blob/main/docs/TH1520%20System%20User%20Manual.pdf

Signed-off-by: Michal Wilczynski <[email protected]>
Acked-by: Drew Fustini <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Ulf Hansson <[email protected]>

show more ...

firmware: add Exynos ACPM protocol driver

Alive Clock and Power Manager (ACPM) Message Protocol is defined for
the purpose of communication between the ACPM firmware and masters
(AP, AOC, ...). ACPM

firmware: add Exynos ACPM protocol driver

Alive Clock and Power Manager (ACPM) Message Protocol is defined for
the purpose of communication between the ACPM firmware and masters
(AP, AOC, ...). ACPM firmware operates on the Active Power Management
(APM) module that handles overall power activities.

ACPM and masters regard each other as independent hardware component and
communicate with each other using mailbox messages and shared memory.

This protocol driver provides the interface for all the client drivers
making use of the features offered by the APM. Add ACPM protocol support.

Signed-off-by: Tudor Ambarus <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Krzysztof Kozlowski <[email protected]>

show more ...

firmware: microchip: add PolarFire SoC Auto Update support

Add support for Auto Update reprogramming of the FPGA fabric on
PolarFire SoC, using the fw_upload mechanism a la the
intel-m10-bmc-sec-upd

firmware: microchip: add PolarFire SoC Auto Update support

Add support for Auto Update reprogramming of the FPGA fabric on
PolarFire SoC, using the fw_upload mechanism a la the
intel-m10-bmc-sec-update driver.

This driver only writes the image to the spi flash & performs
validation on it, as the entire FPGA becomes unusable during the actual
reprogramming of a bitstream. To initiate the reprogramming itself, a
device reset is required. The SBI SRST extension's "cold reboot" can
trigger such a device reset, provided corresponding support has been
enabled in the HSS (Hart Software Services), the provider of SBI runtime
services on PolarFire SoC.

While this is a driver responsible for the reprogramming of an FPGA,
there is no dynamic discovery of devices involved, as runtime
reconfiguration is not possible due to the device reset requirements.
Therefore FPGA manager subsystem is not used by this driver and the FPGA
subsystem maintainers were unwilling to accept it there.

Signed-off-by: Conor Dooley <[email protected]>

show more ...

firmware: arm_scpi: Move power-domain driver to the pmdomain dir

To simplify with maintenance let's move the Arm SCPI power-domain driver
to the new pmdomain directory. Note this is different from a

firmware: arm_scpi: Move power-domain driver to the pmdomain dir

To simplify with maintenance let's move the Arm SCPI power-domain driver
to the new pmdomain directory. Note this is different from and precedes
the new Arm SCMI protocol.

Signed-off-by: Sudeep Holla <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Ulf Hansson <[email protected]>

show more ...

firmware: qcom: move Qualcomm code into its own directory

We're getting more and more qcom specific .c files in drivers/firmware/
and about to get even more. Create a separate directory for Qualcomm

firmware: qcom: move Qualcomm code into its own directory

We're getting more and more qcom specific .c files in drivers/firmware/
and about to get even more. Create a separate directory for Qualcomm
firmware drivers and move existing sources in there.

Signed-off-by: Bartosz Golaszewski <[email protected]>
Acked-by: Elliot Berman <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Reviewed-by: Maximilian Luz <[email protected]>
Tested-by: Andrew Halaney <[email protected]> # sc8280xp-lenovo-thinkpad-x13s
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>

show more ...

firmware: Add support for Qualcomm UEFI Secure Application

On platforms using the Qualcomm UEFI Secure Application (uefisecapp),
EFI variables cannot be accessed via the standard interface in EFI
ru

firmware: Add support for Qualcomm UEFI Secure Application

On platforms using the Qualcomm UEFI Secure Application (uefisecapp),
EFI variables cannot be accessed via the standard interface in EFI
runtime mode. The respective functions return EFI_UNSUPPORTED. On these
platforms, we instead need to talk to uefisecapp. This commit provides
support for this and registers the respective efivars operations to
access EFI variables from the kernel.

Communication with uefisecapp follows the Qualcomm QSEECOM / Secure OS
conventions via the respective SCM call interface. This is also the
reason why variable access works normally while boot services are
active. During this time, said SCM interface is managed by the boot
services. When calling ExitBootServices(), the ownership is transferred
to the kernel. Therefore, UEFI must not use that interface itself (as
multiple parties accessing this interface at the same time may lead to
complications) and cannot access variables for us.

Signed-off-by: Maximilian Luz <[email protected]>
Acked-by: Ard Biesheuvel <[email protected]>
Reviewed-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>

show more ...

firmware: qcom_scm: Add support for Qualcomm Secure Execution Environment SCM interface

Add support for SCM calls to Secure OS and the Secure Execution
Environment (SEE) residing in the TrustZone (T

firmware: qcom_scm: Add support for Qualcomm Secure Execution Environment SCM interface

Add support for SCM calls to Secure OS and the Secure Execution
Environment (SEE) residing in the TrustZone (TZ) via the QSEECOM
interface. This allows communication with Secure/TZ applications, for
example 'uefisecapp' managing access to UEFI variables.

For better separation, make qcom_scm spin up a dedicated child
(platform) device in case QSEECOM support has been detected. The
corresponding driver for this device is then responsible for managing
any QSEECOM clients. Specifically, this driver attempts to automatically
detect known and supported applications, creating a client (auxiliary)
device for each one. The respective client/auxiliary driver is then
responsible for managing and communicating with the application.

While this patch introduces only a very basic interface without the more
advanced features (such as re-entrant and blocking SCM calls and
listeners/callbacks), this is enough to talk to the aforementioned
'uefisecapp'.

Signed-off-by: Maximilian Luz <[email protected]>
Reviewed-by: Johan Hovold <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>

show more ...

arch: Remove Itanium (IA-64) architecture

The Itanium architecture is obsolete, and an informal survey [0] reveals
that any residual use of Itanium hardware in production is mostly HP-UX
or OpenVMS

arch: Remove Itanium (IA-64) architecture

The Itanium architecture is obsolete, and an informal survey [0] reveals
that any residual use of Itanium hardware in production is mostly HP-UX
or OpenVMS based. The use of Linux on Itanium appears to be limited to
enthusiasts that occasionally boot a fresh Linux kernel to see whether
things are still working as intended, and perhaps to churn out some
distro packages that are rarely used in practice.

None of the original companies behind Itanium still produce or support
any hardware or software for the architecture, and it is listed as
'Orphaned' in the MAINTAINERS file, as apparently, none of the engineers
that contributed on behalf of those companies (nor anyone else, for that
matter) have been willing to support or maintain the architecture
upstream or even be responsible for applying the odd fix. The Intel
firmware team removed all IA-64 support from the Tianocore/EDK2
reference implementation of EFI in 2018. (Itanium is the original
architecture for which EFI was developed, and the way Linux supports it
deviates significantly from other architectures.) Some distros, such as
Debian and Gentoo, still maintain [unofficial] ia64 ports, but many have
dropped support years ago.

While the argument is being made [1] that there is a 'for the common
good' angle to being able to build and run existing projects such as the
Grid Community Toolkit [2] on Itanium for interoperability testing, the
fact remains that none of those projects are known to be deployed on
Linux/ia64, and very few people actually have access to such a system in
the first place. Even if there were ways imaginable in which Linux/ia64
could be put to good use today, what matters is whether anyone is
actually doing that, and this does not appear to be the case.

There are no emulators widely available, and so boot testing Itanium is
generally infeasible for ordinary contributors. GCC still supports IA-64
but its compile farm [3] no longer has any IA-64 machines. GLIBC would
like to get rid of IA-64 [4] too because it would permit some overdue
code cleanups. In summary, the benefits to the ecosystem of having IA-64
be part of it are mostly theoretical, whereas the maintenance overhead
of keeping it supported is real.

So let's rip off the band aid, and remove the IA-64 arch code entirely.
This follows the timeline proposed by the Debian/ia64 maintainer [5],
which removes support in a controlled manner, leaving IA-64 in a known
good state in the most recent LTS release. Other projects will follow
once the kernel support is removed.

[0] https://lore.kernel.org/all/CAMj1kXFCMh_578jniKpUtx_j8ByHnt=s7S+yQ+vGbKt9ud7+kQ@mail.gmail.com/
[1] https://lore.kernel.org/all/[email protected]/
[2] https://gridcf.org/gct-docs/latest/index.html
[3] https://cfarm.tetaneutral.net/machines/list/
[4] https://lore.kernel.org/all/[email protected]/
[5] https://lore.kernel.org/all/ff58a3e76e5102c94bb5946d99187b358def688a.camel@physik.fu-berlin.de/

Acked-by: Tony Luck <[email protected]>
Signed-off-by: Ard Biesheuvel <[email protected]>

show more ...

efi: clean up Kconfig dependencies on CONFIG_EFI

Geert reports that the new option CONFIG_EFI_DISABLE_RUNTIME is user
visible even when EFI support is disabled, which is unnecessary and
clutters the

efi: clean up Kconfig dependencies on CONFIG_EFI

Geert reports that the new option CONFIG_EFI_DISABLE_RUNTIME is user
visible even when EFI support is disabled, which is unnecessary and
clutters the Kconfig interface.

So let's move this option into the existing Kconfig submenu that already
depends on CONFIG_EFI, and while at it, give some other options the same
treatment.

Also clean up a small wart where the efi/ subdirectory is listed twice.
Let's just list it unconditionally so that both EFI and UEFI_CPER based
pieces will be built independently (the latter only depends on the
former on !X86)

Signed-off-by: Ard Biesheuvel <[email protected]>

show more ...

firmware: mediatek: Add adsp ipc protocol interface

Some of mediatek processors contain
the Tensilica HiFix DSP for audio processing.

The communication between Host CPU and DSP firmware is
taking p

firmware: mediatek: Add adsp ipc protocol interface

Some of mediatek processors contain
the Tensilica HiFix DSP for audio processing.

The communication between Host CPU and DSP firmware is
taking place using a shared memory area for message passing.

ADSP IPC protocol offers (send/recv) interfaces using
mediatek-mailbox APIs.

We use two mbox channels to implement a request-reply protocol.

Signed-off-by: Allen-KH Cheng <[email protected]>
Signed-off-by: TingHan Shen <[email protected]>
Reviewed-by: Pierre-Louis Bossart <[email protected]>
Reviewed-by: Curtis Malainey <[email protected]>
Reviewed-by: Tzung-Bi Shih <[email protected]>
Reviewed-by: YC Hung <[email protected]>
Reviewed-by: AngeloGioacchino Del Regno <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>

show more ...

firmware: cs_dsp: add driver to support firmware loading on Cirrus Logic DSPs

wm_adsp originally provided firmware loading on some audio DSP and was
implemented as an ASoC codec driver. However, the

firmware: cs_dsp: add driver to support firmware loading on Cirrus Logic DSPs

wm_adsp originally provided firmware loading on some audio DSP and was
implemented as an ASoC codec driver. However, the firmware loading now
covers a wider range of DSP cores and peripherals containing them,
beyond just audio. So it needs to be available to non-audio drivers. All
the core firmware loading support has been moved into a new driver
cs_dsp, leaving only the ASoC-specific parts in wm_adsp.

Signed-off-by: Simon Trimmer <[email protected]>
Signed-off-by: Charles Keepax <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Mark Brown <[email protected]>

show more ...

drivers/firmware: consolidate EFI framebuffer setup for all arches

The register_gop_device() function registers an "efi-framebuffer" platform
device to match against the efifb driver, to have an ear

drivers/firmware: consolidate EFI framebuffer setup for all arches

The register_gop_device() function registers an "efi-framebuffer" platform
device to match against the efifb driver, to have an early framebuffer for
EFI platforms.

But there is already support to do exactly the same by the Generic System
Framebuffers (sysfb) driver. This used to be only for X86 but it has been
moved to drivers/firmware and could be reused by other architectures.

Also, besides supporting registering an "efi-framebuffer", this driver can
register a "simple-framebuffer" allowing to use the siple{fb,drm} drivers
on non-X86 EFI platforms. For example, on aarch64 these drivers can only
be used with DT and doesn't have code to register a "simple-frambuffer"
platform device when booting with EFI.

For these reasons, let's remove the register_gop_device() duplicated code
and instead move the platform specific logic that's there to sysfb driver.

Signed-off-by: Javier Martinez Canillas <[email protected]>
Acked-by: Borislav Petkov <[email protected]>
Acked-by: Daniel Vetter <[email protected]>
Signed-off-by: Thomas Zimmermann <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]

show more ...

drivers/firmware: move x86 Generic System Framebuffers support

The x86 architecture has generic support to register a system framebuffer
platform device. It either registers a "simple-framebuffer" i

drivers/firmware: move x86 Generic System Framebuffers support

The x86 architecture has generic support to register a system framebuffer
platform device. It either registers a "simple-framebuffer" if the config
option CONFIG_X86_SYSFB is enabled, or a legacy VGA/VBE/EFI FB device.

But the code is generic enough to be reused by other architectures and can
be moved out of the arch/x86 directory.

This will allow to also support the simple{fb,drm} drivers on non-x86 EFI
platforms, such as aarch64 where these drivers are only supported with DT.

Signed-off-by: Javier Martinez Canillas <[email protected]>
Acked-by: Borislav Petkov <[email protected]>
Acked-by: Greg Kroah-Hartman <[email protected]>
Acked-by: Daniel Vetter <[email protected]>
Signed-off-by: Thomas Zimmermann <[email protected]>
Link: https://patchwork.freedesktop.org/patch/msgid/[email protected]

show more ...

firmware: qcom_scm: Allow qcom_scm driver to be loadable as a permenent module

Allow the qcom_scm driver to be loadable as a permenent module.

This still uses the "depends on QCOM_SCM || !QCOM_SCM"

firmware: qcom_scm: Allow qcom_scm driver to be loadable as a permenent module

Allow the qcom_scm driver to be loadable as a permenent module.

This still uses the "depends on QCOM_SCM || !QCOM_SCM" bit to
ensure that drivers that call into the qcom_scm driver are
also built as modules. While not ideal in some cases its the
only safe way I can find to avoid build errors without having
those drivers select QCOM_SCM and have to force it on (as
QCOM_SCM=n can be valid for those drivers).

Reviving this now that Saravana's fw_devlink defaults to on,
which should avoid loading troubles seen before.

Acked-by: Kalle Valo <[email protected]>
Acked-by: Greg Kroah-Hartman <[email protected]>
Acked-by: Will Deacon <[email protected]>
Reviewed-by: Bjorn Andersson <[email protected]>
Signed-off-by: John Stultz <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>

show more ...

firmware: arm_ffa: Add initial FFA bus support for device enumeration

The Arm FF for Armv8-A specification has concept of endpoints or
partitions. In the Normal world, a partition could be a VM when

firmware: arm_ffa: Add initial FFA bus support for device enumeration

The Arm FF for Armv8-A specification has concept of endpoints or
partitions. In the Normal world, a partition could be a VM when
the Virtualization extension is enabled or the kernel itself.

In order to handle multiple partitions, we can create a FFA device for
each such partition on a dedicated FFA bus. Similarly, different drivers
requiring FFA transport can be registered on the same bus. We can match
the device and drivers using UUID. This is mostly for the in-kernel
users with FFA drivers.

Link: https://lore.kernel.org/r/[email protected]
Tested-by: Jens Wiklander <[email protected]>
Signed-off-by: Sudeep Holla <[email protected]>

show more ...

Revert "firmware: QCOM_SCM: Allow qcom_scm driver to be loadable as a permenent module"

This reverts commit d0511b5496c03cdbcda55a9b57c32cdd751920ed.

After some time it was noticed that the Tegra18

Revert "firmware: QCOM_SCM: Allow qcom_scm driver to be loadable as a permenent module"

This reverts commit d0511b5496c03cdbcda55a9b57c32cdd751920ed.

After some time it was noticed that the Tegra186 among others
were experiencing problems when making this into a module.

Signed-off-by: Linus Walleij <[email protected]>

show more ...

firmware: QCOM_SCM: Allow qcom_scm driver to be loadable as a permenent module

Allow the qcom_scm driver to be loadable as a permenent module.

This still uses the "depends on QCOM_SCM || !QCOM_SCM"

firmware: QCOM_SCM: Allow qcom_scm driver to be loadable as a permenent module

Allow the qcom_scm driver to be loadable as a permenent module.

This still uses the "depends on QCOM_SCM || !QCOM_SCM" bit to
ensure that drivers that call into the qcom_scm driver are
also built as modules. While not ideal in some cases its the
only safe way I can find to avoid build errors without having
those drivers select QCOM_SCM and have to force it on (as
QCOM_SCM=n can be valid for those drivers).

Signed-off-by: John Stultz <[email protected]>
Reviewed-by: Bjorn Andersson <[email protected]>
Acked-by: Kalle Valo <[email protected]>
Acked-by: Greg Kroah-Hartman <[email protected]>
Cc: Catalin Marinas <[email protected]>
Cc: Will Deacon <[email protected]>
Cc: Andy Gross <[email protected]>
Cc: Bjorn Andersson <[email protected]>
Cc: Joerg Roedel <[email protected]>
Cc: Thomas Gleixner <[email protected]>
Cc: Jason Cooper <[email protected]>
Cc: Marc Zyngier <[email protected]>
Cc: Linus Walleij <[email protected]>
Cc: Vinod Koul <[email protected]>
Cc: Kalle Valo <[email protected]>
Cc: Maulik Shah <[email protected]>
Cc: Lina Iyer <[email protected]>
Cc: Saravana Kannan <[email protected]>
Cc: Todd Kjos <[email protected]>
Cc: Greg Kroah-Hartman <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Linus Walleij <[email protected]>

show more ...

firmware: arm_scmi: Enable building as a single module

Now, with all the plumbing in place to enable building scmi as a module
instead of built-in modules, let us enable the same.

Link: https://lor

firmware: arm_scmi: Enable building as a single module

Now, with all the plumbing in place to enable building scmi as a module
instead of built-in modules, let us enable the same.

Link: https://lore.kernel.org/r/[email protected]
Tested-by: Cristian Marussi <[email protected]>
Signed-off-by: Sudeep Holla <[email protected]>

show more ...

firmware: smccc: Refactor SMCCC specific bits into separate file

In order to add newer SMCCC v1.1+ functionality and to avoid cluttering
PSCI firmware driver with SMCCC bits, let us move the SMCCC s

firmware: smccc: Refactor SMCCC specific bits into separate file

In order to add newer SMCCC v1.1+ functionality and to avoid cluttering
PSCI firmware driver with SMCCC bits, let us move the SMCCC specific
details under drivers/firmware/smccc/smccc.c

We can also drop conduit and smccc_version from psci_operations structure
as SMCCC was the sole user and now it maintains those.

No functionality change in this patch though.

Signed-off-by: Sudeep Holla <[email protected]>
Tested-by: Etienne Carriere <[email protected]>
Reviewed-by: Etienne Carriere <[email protected]>
Acked-by: Mark Rutland <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Will Deacon <[email protected]>

show more ...

firmware: qcom_scm: Dynamically support SMCCC and legacy conventions

Dynamically support SMCCCC and legacy conventions by detecting which
convention to use at runtime. qcom_scm_call_atomic and qcom_

firmware: qcom_scm: Dynamically support SMCCC and legacy conventions

Dynamically support SMCCCC and legacy conventions by detecting which
convention to use at runtime. qcom_scm_call_atomic and qcom_scm_call can
then be moved in qcom_scm.c and use underlying convention backend as
appropriate. Thus, rename qcom_scm-64,-32 to reflect that they are
backends for -smc and -legacy, respectively.

Also add support for making SCM calls earlier than when SCM driver
probes to support use cases such as qcom_scm_set_cold_boot_addr. Support
is added by lazily initializing the convention and guarding the query
with a spin lock. The limitation of these early SCM calls is that they
cannot use DMA, as in the case of >4 arguments for SMC convention and
any non-atomic call for legacy convention.

Tested-by: Brian Masney <[email protected]> # arm32
Tested-by: Stephan Gerhold <[email protected]>
Signed-off-by: Elliot Berman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>

show more ...

firmware: qcom_scm-32: Use SMC arch wrappers

Use SMC arch wrappers instead of inline assembly.

Tested-by: Brian Masney <[email protected]> # arm32
Tested-by: Stephan Gerhold <[email protected]

firmware: qcom_scm-32: Use SMC arch wrappers

Use SMC arch wrappers instead of inline assembly.

Tested-by: Brian Masney <[email protected]> # arm32
Tested-by: Stephan Gerhold <[email protected]>
Signed-off-by: Elliot Berman <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Bjorn Andersson <[email protected]>

show more ...

firmware: Add Turris Mox rWTM firmware driver

This adds a driver to communicate with the firmware running on the
secure processor of the Turris Mox router, enabling the kernel to
retrieve true rando

firmware: Add Turris Mox rWTM firmware driver

This adds a driver to communicate with the firmware running on the
secure processor of the Turris Mox router, enabling the kernel to
retrieve true random numbers from the Entropy Bit Generator and to read
some information burned into eFuses when device was manufactured:

and to
sign messages with the ECDSA private key burned into each Turris Mox
device when manufacturing.

This also adds support to read other information burned into eFuses:
- serial number
- board version
- MAC addresses
- RAM size
- ECDSA public key (this is not read directly from eFuses, rather it
is computed by the firmware as pair to the burned private key)

The source code of the firmware is open source and can be found at
https://gitlab.labs.nic.cz/turris/mox-boot-builder/tree/master/wtmi

The firmware is also able to, on demand, sign messages with the burned
ECDSA private key, but since Linux's akcipher API is not yet stable
(and therefore not exposed to userspace via netlink), this functionality
is not supported yet.

Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Marek Behún <[email protected]>
Signed-off-by: Arnd Bergmann <[email protected]>

show more ...

firmware: add Intel Stratix10 remote system update driver

The Intel Remote System Update (RSU) driver exposes interfaces access
through the Intel Service Layer to user space via sysfs interface.
The

firmware: add Intel Stratix10 remote system update driver

The Intel Remote System Update (RSU) driver exposes interfaces access
through the Intel Service Layer to user space via sysfs interface.
The RSU interfaces report and control some of the optional RSU features
on Intel Stratix 10 SoC.

The RSU feature provides a way for customers to update the boot
configuration of a Intel Stratix 10 SoC device with significantly reduced
risk of corrupting the bitstream storage and bricking the system.

Signed-off-by: Richard Gong <[email protected]>
Reviewed-by: Alan Tull <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

firmware: Move Trusted Foundations support

Move the Trusted Foundations support out of arch/arm/firmware and into
drivers/firmware where most other firmware support implementations are
located.

Sig

firmware: Move Trusted Foundations support

Move the Trusted Foundations support out of arch/arm/firmware and into
drivers/firmware where most other firmware support implementations are
located.

Signed-off-by: Thierry Reding <[email protected]>

show more ...

drivers: firmware: psci: Move psci to separate directory

Some following changes extends the PSCI driver with some additional
files. Avoid to continue cluttering the toplevel firmware directory
and

drivers: firmware: psci: Move psci to separate directory

Some following changes extends the PSCI driver with some additional
files. Avoid to continue cluttering the toplevel firmware directory
and first move the PSCI files into a PSCI sub-directory.

Suggested-by: Mark Rutland <[email protected]>
Signed-off-by: Ulf Hansson <[email protected]>
Acked-by: Daniel Lezcano <[email protected]>
Acked-by: Mark Rutland <[email protected]>
Acked-by: Lorenzo Pieralisi <[email protected]>
Signed-off-by: Rafael J. Wysocki <[email protected]>

show more ...