crypto: caam - fix return code in completion callbacks

Modify drive to provide a valid errno (and not the HW error ID)
to the user, via completion callbacks.

A "valid errno" is currently not explic

crypto: caam - fix return code in completion callbacks

Modify drive to provide a valid errno (and not the HW error ID)
to the user, via completion callbacks.

A "valid errno" is currently not explicitly mentioned in the docs,
however the error code is expected to match the one returned by the
generic SW implementation.

Note: in most error cases caam/qi and caam/qi2 returned -EIO; align all
caam drivers to return -EINVAL.

While here, ratelimit prints triggered by fuzz testing, such that
console is not flooded.

Signed-off-by: Horia Geantă <[email protected]>
Signed-off-by: Iuliana Prodan <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>

show more ...

crypto: caam - print messages in caam_dump_sg at debug level

caam_dump_sg() is only compiled in when DEBUG is defined, hence the
messages are debug messages. Remove the @level argument from
caam_dum

crypto: caam - print messages in caam_dump_sg at debug level

caam_dump_sg() is only compiled in when DEBUG is defined, hence the
messages are debug messages. Remove the @level argument from
caam_dump_sg() and print all messages at debug level.

Signed-off-by: Sascha Hauer <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>

show more ...

crypto: caam - fix SHA support detection

The addition of Chacha20 + Poly1305 authenc support inadvertently broke
detection of algorithms supported by MDHA (Message Digest Hardware
Accelerator), fix

crypto: caam - fix SHA support detection

The addition of Chacha20 + Poly1305 authenc support inadvertently broke
detection of algorithms supported by MDHA (Message Digest Hardware
Accelerator), fix it.

Fixes: d6bbd4eea243 ("crypto: caam/jr - add support for Chacha20 + Poly1305")
Signed-off-by: Horia Geantă <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>

show more ...

crypto: caam - add Queue Interface v2 error codes

Add support to translate error codes returned by QI v2, i.e.
Queue Interface present on DataPath Acceleration Architecture
v2 (DPAA2).

Signed-off-b

crypto: caam - add Queue Interface v2 error codes

Add support to translate error codes returned by QI v2, i.e.
Queue Interface present on DataPath Acceleration Architecture
v2 (DPAA2).

Signed-off-by: Horia Geantă <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>

show more ...

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.

For non */uapi/* files that summary was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139

and resulted in the first patch in this series.

If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930

and resulted in the second patch in this series.

- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:

SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1

and that resulted in the third patch in this series.

- when the two scanners agreed on the detected license(s), that became
the concluded license(s).

- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.

- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).

- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.

- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct

This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <[email protected]>
Reviewed-by: Philippe Ombredanne <[email protected]>
Reviewed-by: Thomas Gleixner <[email protected]>
Signed-off-by: Greg Kroah-Hartman <[email protected]>

show more ...

crypto: caam/qi - fix compilation with DEBUG enabled

caam/qi driver does not compile when DEBUG is enabled
(CRYPTO_DEV_FSL_CAAM_DEBUG=y):

drivers/crypto/caam/caamalg_qi.c: In function 'ablkcipher_d

crypto: caam/qi - fix compilation with DEBUG enabled

caam/qi driver does not compile when DEBUG is enabled
(CRYPTO_DEV_FSL_CAAM_DEBUG=y):

drivers/crypto/caam/caamalg_qi.c: In function 'ablkcipher_done':
drivers/crypto/caam/caamalg_qi.c:794:2: error: implicit declaration of function 'dbg_dump_sg' [-Werror=implicit-function-declaration]
dbg_dump_sg(KERN_ERR, "dst @" __stringify(__LINE__)": ",

Since dbg_dump_sg() is shared between caam/jr and caam/qi, move it
in a shared location and export it.

At the same time:
-reduce ifdeferry by providing a no-op implementation for !DEBUG case
-rename it to caam_dump_sg() to be consistent in terms of
exported symbols namespace (caam_*)

Cc: <[email protected]>
Fixes: b189817cf789 ("crypto: caam/qi - add ablkcipher and authenc algorithms")
Signed-off-by: Horia Geantă <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>

show more ...

crypto: caam - Contain caam_jr_strstatus() ugliness

The tentacles of this function were firmly attached to various
places in the CAAM code. Just cut them, or this cthulhu function
will sprout them a

crypto: caam - Contain caam_jr_strstatus() ugliness

The tentacles of this function were firmly attached to various
places in the CAAM code. Just cut them, or this cthulhu function
will sprout them anew.

Signed-off-by: Marek Vasut <[email protected]>
Cc: Herbert Xu <[email protected]>
Cc: Horia Geanta <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>

show more ...

crypto: caam - fix printk recursion for long error texts

during recent descriptor development, an Invalid Sequence Command
error triggered a:

BUG: recent printk recursion!

due to insufficient memo

crypto: caam - fix printk recursion for long error texts

during recent descriptor development, an Invalid Sequence Command
error triggered a:

BUG: recent printk recursion!

due to insufficient memory allocated for the error text.

The Invalid Sequence Command error text is the longest.
The length of the maximum error string is computed as
the sum of:

"DECO: ": 6
"jump tgt desc idx 255: ": 23
Invalid Sequence Command text: 272
zero termination character: 1

i.e, 302 characters.

Define this maximum error string length in error.h and fix
caam_jr_strstatus callsites.

Signed-off-by: Kim Phillips <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>

show more ...

crypto: caam - Add support for the Freescale SEC4/CAAM

The SEC4 supercedes the SEC2.x/3.x as Freescale's
Integrated Security Engine. Its programming model is
incompatible with all prior versions of

crypto: caam - Add support for the Freescale SEC4/CAAM

The SEC4 supercedes the SEC2.x/3.x as Freescale's
Integrated Security Engine. Its programming model is
incompatible with all prior versions of the SEC (talitos).

The SEC4 is also known as the Cryptographic Accelerator
and Assurance Module (CAAM); this driver is named caam.

This initial submission does not include support for Data Path
mode operation - AEAD descriptors are submitted via the job
ring interface, while the Queue Interface (QI) is enabled
for use by others. Only AEAD algorithms are implemented
at this time, for use with IPsec.

Many thanks to the Freescale STC team for their contributions
to this driver.

Signed-off-by: Steve Cornelius <[email protected]>
Signed-off-by: Kim Phillips <[email protected]>
Signed-off-by: Herbert Xu <[email protected]>

show more ...