LoongArch: Don't crash in stack_top() for tasks without vDSO

Not all tasks have a vDSO mapped, for example kthreads never do. If such
a task ever ends up calling stack_top(), it will derefence the N

LoongArch: Don't crash in stack_top() for tasks without vDSO

Not all tasks have a vDSO mapped, for example kthreads never do. If such
a task ever ends up calling stack_top(), it will derefence the NULL vdso
pointer and crash.

This can for example happen when using kunit:

[<9000000000203874>] stack_top+0x58/0xa8
[<90000000002956cc>] arch_pick_mmap_layout+0x164/0x220
[<90000000003c284c>] kunit_vm_mmap_init+0x108/0x12c
[<90000000003c1fbc>] __kunit_add_resource+0x38/0x8c
[<90000000003c2704>] kunit_vm_mmap+0x88/0xc8
[<9000000000410b14>] usercopy_test_init+0xbc/0x25c
[<90000000003c1db4>] kunit_try_run_case+0x5c/0x184
[<90000000003c3d54>] kunit_generic_run_threadfn_adapter+0x24/0x48
[<900000000022e4bc>] kthread+0xc8/0xd4
[<9000000000200ce8>] ret_from_kernel_thread+0xc/0xa4

Fixes: 803b0fc5c3f2 ("LoongArch: Add process management")
Signed-off-by: Thomas Weißschuh <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>

show more ...

LoongArch: Fix and simplify fcsr initialization on execve()

There has been a lingering bug in LoongArch Linux systems causing some
GCC tests to intermittently fail (see Closes link). I've made a mi

LoongArch: Fix and simplify fcsr initialization on execve()

There has been a lingering bug in LoongArch Linux systems causing some
GCC tests to intermittently fail (see Closes link). I've made a minimal
reproducer:

zsh% cat measure.s
.align 4
.globl _start
_start:
movfcsr2gr $a0, $fcsr0
bstrpick.w $a0, $a0, 16, 16
beqz $a0, .ok
break 0
.ok:
li.w $a7, 93
syscall 0
zsh% cc mesaure.s -o measure -nostdlib
zsh% echo $((1.0/3))
0.33333333333333331
zsh% while ./measure; do ; done

This while loop should not stop as POSIX is clear that execve must set
fenv to the default, where FCSR should be zero. But in fact it will
just stop after running for a while (normally less than 30 seconds).
Note that "$((1.0/3))" is needed to reproduce this issue because it
raises FE_INVALID and makes fcsr0 non-zero.

The problem is we are currently relying on SET_PERSONALITY2() to reset
current->thread.fpu.fcsr. But SET_PERSONALITY2() is executed before
start_thread which calls lose_fpu(0). We can see if kernel preempt is
enabled, we may switch to another thread after SET_PERSONALITY2() but
before lose_fpu(0). Then bad thing happens: during the thread switch
the value of the fcsr0 register is stored into current->thread.fpu.fcsr,
making it dirty again.

The issue can be fixed by setting current->thread.fpu.fcsr after
lose_fpu(0) because lose_fpu() clears TIF_USEDFPU, then the thread
switch won't touch current->thread.fpu.fcsr.

The only other architecture setting FCSR in SET_PERSONALITY2() is MIPS.
I've ran a similar test on MIPS with mainline kernel and it turns out
MIPS is buggy, too. Anyway MIPS do this for supporting different FP
flavors (NaN encodings, etc.) which do not exist on LoongArch. So for
LoongArch, we can simply remove the current->thread.fpu.fcsr setting
from SET_PERSONALITY2() and do it in start_thread(), after lose_fpu(0).

The while loop failing with the mainline kernel has survived one hour
after this change on LoongArch.

Fixes: 803b0fc5c3f2baa ("LoongArch: Add process management")
Closes: https://github.com/loongson-community/discussions/issues/7
Link: https://lore.kernel.org/linux-mips/[email protected]/
Cc: [email protected]
Signed-off-by: Xi Ruoyao <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>

show more ...

LoongArch: Fix some build warnings with W=1

There are some building warnings when building LoongArch kernel with W=1
as following, this patch fixes them.

arch/loongarch/kernel/acpi.c:284:13: warnin

LoongArch: Fix some build warnings with W=1

There are some building warnings when building LoongArch kernel with W=1
as following, this patch fixes them.

arch/loongarch/kernel/acpi.c:284:13: warning: no previous prototype for ‘acpi_numa_arch_fixup’ [-Wmissing-prototypes]
284 | void __init acpi_numa_arch_fixup(void) {}
| ^~~~~~~~~~~~~~~~~~~~
arch/loongarch/kernel/time.c:32:13: warning: no previous prototype for ‘constant_timer_interrupt’ [-Wmissing-prototypes]
32 | irqreturn_t constant_timer_interrupt(int irq, void *data)
| ^~~~~~~~~~~~~~~~~~~~~~~~
arch/loongarch/kernel/traps.c:496:25: warning: no previous prototype for 'do_fpe' [-Wmissing-prototypes]
496 | asmlinkage void noinstr do_fpe(struct pt_regs *regs
| ^~~~~~
arch/loongarch/kernel/traps.c:813:22: warning: variable ‘opcode’ set but not used [-Wunused-but-set-variable]
813 | unsigned int opcode;
| ^~~~~~
arch/loongarch/kernel/signal.c:895:14: warning: no previous prototype for ‘get_sigframe’ [-Wmissing-prototypes]
895 | void __user *get_sigframe(struct ksignal *ksig, struct pt_regs *regs,
| ^~~~~~~~~~~~
arch/loongarch/kernel/syscall.c:21:40: warning: initialized field overwritten [-Woverride-init]
21 | #define __SYSCALL(nr, call) [nr] = (call),
| ^
arch/loongarch/kernel/syscall.c:40:14: warning: no previous prototype for ‘do_syscall’ [-Wmissing-prototypes]
40 | void noinstr do_syscall(struct pt_regs *regs)
| ^~~~~~~~~~
arch/loongarch/kernel/smp.c:502:17: warning: no previous prototype for ‘start_secondary’ [-Wmissing-prototypes]
502 | asmlinkage void start_secondary(void)
| ^~~~~~~~~~~~~~~
arch/loongarch/kernel/process.c:309:15: warning: no previous prototype for ‘arch_align_stack’ [-Wmissing-prototypes]
309 | unsigned long arch_align_stack(unsigned long sp)
| ^~~~~~~~~~~~~~~~
arch/loongarch/kernel/topology.c:13:5: warning: no previous prototype for ‘arch_register_cpu’ [-Wmissing-prototypes]
13 | int arch_register_cpu(int cpu)
| ^~~~~~~~~~~~~~~~~
arch/loongarch/kernel/topology.c:27:6: warning: no previous prototype for ‘arch_unregister_cpu’ [-Wmissing-prototypes]
27 | void arch_unregister_cpu(int cpu)
| ^~~~~~~~~~~~~~~~~~~
arch/loongarch/kernel/module-sections.c:103:5: warning: no previous prototype for ‘module_frob_arch_sections’ [-Wmissing-prototypes]
103 | int module_frob_arch_sections(Elf_Ehdr *ehdr, Elf_Shdr *sechdrs,
| ^~~~~~~~~~~~~~~~~~~~~~~~~
arch/loongarch/mm/hugetlbpage.c:56:5: warning: no previous prototype for ‘is_aligned_hugepage_range’ [-Wmissing-prototypes]
56 | int is_aligned_hugepage_range(unsigned long addr, unsigned long len)
| ^~~~~~~~~~~~~~~~~~~~~~~~~

Signed-off-by: Bibo Mao <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>

show more ...

LoongArch: Add Loongson Binary Translation (LBT) extension support

Loongson Binary Translation (LBT) is used to accelerate binary translation,
which contains 4 scratch registers (scr0 to scr3), x86/

LoongArch: Add Loongson Binary Translation (LBT) extension support

Loongson Binary Translation (LBT) is used to accelerate binary translation,
which contains 4 scratch registers (scr0 to scr3), x86/ARM eflags (eflags)
and x87 fpu stack pointer (ftop).

This patch support kernel to save/restore these registers, handle the LBT
exception and maintain sigcontext.

Signed-off-by: Qi Hu <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>

show more ...

LoongArch: Put the body of play_dead() into arch_cpu_idle_dead()

The initial aim is to silence the following objtool warning:

arch/loongarch/kernel/process.o: warning: objtool: arch_cpu_idle_dead()

LoongArch: Put the body of play_dead() into arch_cpu_idle_dead()

The initial aim is to silence the following objtool warning:

arch/loongarch/kernel/process.o: warning: objtool: arch_cpu_idle_dead() falls through to next function start_thread()

According to tools/objtool/Documentation/objtool.txt, this is because
the last instruction of arch_cpu_idle_dead() is a call to a noreturn
function play_dead(). In order to silence the warning, one simple way
is to add the noreturn function play_dead() to objtool's hard-coded
global_noreturns array, that is to say, just put "NORETURN(play_dead)"
into tools/objtool/noreturns.h, it works well.

But I noticed that play_dead() is only defined once and only called by
arch_cpu_idle_dead(), so put the body of play_dead() into the caller
arch_cpu_idle_dead(), then remove the noreturn function play_dead() is
an alternative way which can reduce the overhead of the function call
at the same time.

Signed-off-by: Tiezhu Yang <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>

show more ...

nmi_backtrace: allow excluding an arbitrary CPU

The APIs that allow backtracing across CPUs have always had a way to
exclude the current CPU. This convenience means callers didn't need to
find a pl

nmi_backtrace: allow excluding an arbitrary CPU

The APIs that allow backtracing across CPUs have always had a way to
exclude the current CPU. This convenience means callers didn't need to
find a place to allocate a CPU mask just to handle the common case.

Let's extend the API to take a CPU ID to exclude instead of just a
boolean. This isn't any more complex for the API to handle and allows the
hardlockup detector to exclude a different CPU (the one it already did a
trace for) without needing to find space for a CPU mask.

Arguably, this new API also encourages safer behavior. Specifically if
the caller wants to avoid tracing the current CPU (maybe because they
already traced the current CPU) this makes it more obvious to the caller
that they need to make sure that the current CPU ID can't change.

[[email protected]: fix trigger_allbutcpu_cpu_backtrace() stub]
Link: https://lkml.kernel.org/r/20230804065935.v4.1.Ia35521b91fc781368945161d7b28538f9996c182@changeid
Signed-off-by: Douglas Anderson <[email protected]>
Acked-by: Michal Hocko <[email protected]>
Cc: kernel test robot <[email protected]>
Cc: Lecopzer Chen <[email protected]>
Cc: Petr Mladek <[email protected]>
Cc: Pingfan Liu <[email protected]>
Signed-off-by: Andrew Morton <[email protected]>

show more ...

LoongArch: Add vector extensions support

Add LoongArch's vector extensions support, which including 128bit LSX
(i.e., Loongson SIMD eXtension) and 256bit LASX (i.e., Loongson Advanced
SIMD eXtension

LoongArch: Add vector extensions support

Add LoongArch's vector extensions support, which including 128bit LSX
(i.e., Loongson SIMD eXtension) and 256bit LASX (i.e., Loongson Advanced
SIMD eXtension).

Linux kernel doesn't use vector itself, it only handle exceptions and
context save/restore. So it only needs a subset of these instructions:

* Vector load/store: vld vst vldx vstx xvld xvst xvldx xvstx
* 8bit-elements move: vpickve2gr.b xvpickve2gr.b vinsgr2vr.b xvinsgr2vr.b
* 16bit-elements move: vpickve2gr.h xvpickve2gr.h vinsgr2vr.h xvinsgr2vr.h
* 32bit-elements move: vpickve2gr.w xvpickve2gr.w vinsgr2vr.w xvinsgr2vr.w
* 64bit-elements move: vpickve2gr.d xvpickve2gr.d vinsgr2vr.d xvinsgr2vr.d
* Elements permute: vpermi.w vpermi.d xvpermi.w xvpermi.d xvpermi.q

Introduce AS_HAS_LSX_EXTENSION and AS_HAS_LASX_EXTENSION to avoid non-
vector toolchains complains unsupported instructions.

Signed-off-by: Huacai Chen <[email protected]>

show more ...

LoongArch: Add support to clone a time namespace

We can see that "Time namespaces are not supported" on LoongArch:

(1) clone3 test
# cd tools/testing/selftests/clone3 && make && ./clone3
...

LoongArch: Add support to clone a time namespace

We can see that "Time namespaces are not supported" on LoongArch:

(1) clone3 test
# cd tools/testing/selftests/clone3 && make && ./clone3
...
# Time namespaces are not supported
ok 18 # SKIP Skipping clone3() with CLONE_NEWTIME
# Totals: pass:17 fail:0 xfail:0 xpass:0 skip:1 error:0

(2) timens test
# cd tools/testing/selftests/timens && make && ./timens
...
1..0 # SKIP Time namespaces are not supported

On LoongArch the current kernel does not support CONFIG_TIME_NS which
depends on GENERIC_VDSO_TIME_NS, select GENERIC_VDSO_TIME_NS to enable
CONFIG_TIME_NS to build kernel/time/namespace.c.

Additionally, it needs to define some arch-dependent functions for the
timens, such as __arch_get_timens_vdso_data(), arch_get_vdso_data() and
vdso_join_timens().

At the same time, modify the layout of vvar to use one page size for
generic vdso data, expand another page size for timens vdso data and
assign LOONGARCH_VDSO_DATA_SIZE (maybe exceeds a page size if expand in
the future) for loongarch vdso data, at last add the callback function
vvar_fault() and modify stack_top().

With this patch under CONFIG_TIME_NS:

(1) clone3 test
# cd tools/testing/selftests/clone3 && make && ./clone3
...
ok 18 [739] Result (0) matches expectation (0)
# Totals: pass:18 fail:0 xfail:0 xpass:0 skip:0 error:0

(2) timens test
# cd tools/testing/selftests/timens && make && ./timens
...
# Totals: pass:10 fail:0 xfail:0 xpass:0 skip:0 error:0

Signed-off-by: Tiezhu Yang <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>

show more ...

sched/idle: Mark arch_cpu_idle_dead() __noreturn

Before commit 076cbf5d2163 ("x86/xen: don't let xen_pv_play_dead()
return"), in Xen, when a previously offlined CPU was brought back
online, it unexp

sched/idle: Mark arch_cpu_idle_dead() __noreturn

Before commit 076cbf5d2163 ("x86/xen: don't let xen_pv_play_dead()
return"), in Xen, when a previously offlined CPU was brought back
online, it unexpectedly resumed execution where it left off in the
middle of the idle loop.

There were some hacks to make that work, but the behavior was surprising
as do_idle() doesn't expect an offlined CPU to return from the dead (in
arch_cpu_idle_dead()).

Now that Xen has been fixed, and the arch-specific implementations of
arch_cpu_idle_dead() also don't return, give it a __noreturn attribute.

This will cause the compiler to complain if an arch-specific
implementation might return. It also improves code generation for both
caller and callee.

Also fixes the following warning:

vmlinux.o: warning: objtool: do_idle+0x25f: unreachable instruction

Reported-by: Paul E. McKenney <[email protected]>
Tested-by: Paul E. McKenney <[email protected]>
Link: https://lore.kernel.org/r/60d527353da8c99d4cf13b6473131d46719ed16d.1676358308.git.jpoimboe@kernel.org
Signed-off-by: Josh Poimboeuf <[email protected]>

show more ...

LoongArch: Add hardware breakpoints/watchpoints support

Use perf framework to manage hardware instruction and data breakpoints.

LoongArch defines hardware watchpoint functions for instruction fetch

LoongArch: Add hardware breakpoints/watchpoints support

Use perf framework to manage hardware instruction and data breakpoints.

LoongArch defines hardware watchpoint functions for instruction fetch
and memory load/store operations. After the software configures hardware
watchpoints, the processor hardware will monitor the access address of
the instruction fetch and load/store operation, and trigger an exception
of the watchpoint when it meets the conditions set by the watchpoint.

The hardware monitoring points for instruction fetching and load/store
operations each have a register for the overall configuration of all
monitoring points, a register for recording the status of all monitoring
points, and four registers required for configuration of each watchpoint
individually.

Signed-off-by: Qing Zhang <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>

show more ...

LoongArch: Get frame info in unwind_start() when regs is not available

At unwind_start(), it is better to get its frame info here rather than
get them outside, even we don't have 'regs'. In this way

LoongArch: Get frame info in unwind_start() when regs is not available

At unwind_start(), it is better to get its frame info here rather than
get them outside, even we don't have 'regs'. In this way we can simply
use unwind_{start, next_frame, done} outside.

Signed-off-by: Jinyang He <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>

show more ...

LoongArch: Add basic STACKPROTECTOR support

Add basic stack protector support similar to other architectures. A
constant canary value is set at boot time, and with help of compiler's
-fstack-protect

LoongArch: Add basic STACKPROTECTOR support

Add basic stack protector support similar to other architectures. A
constant canary value is set at boot time, and with help of compiler's
-fstack-protector we can detect stack corruption.

Signed-off-by: Huacai Chen <[email protected]>

show more ...

LoongArch: Clear FPU/SIMD thread info flags for kernel thread

If a kernel thread is created by a user thread, it may carry FPU/SIMD
thread info flags (TIF_USEDFPU, TIF_USEDSIMD, etc.). Then it will

LoongArch: Clear FPU/SIMD thread info flags for kernel thread

If a kernel thread is created by a user thread, it may carry FPU/SIMD
thread info flags (TIF_USEDFPU, TIF_USEDSIMD, etc.). Then it will be
considered as a fpu owner and kernel try to save its FPU/SIMD context
and cause such errors:

[ 41.518931] do_fpu invoked from kernel context![#1]:
[ 41.523933] CPU: 1 PID: 395 Comm: iou-wrk-394 Not tainted 6.1.0-rc5+ #217
[ 41.530757] Hardware name: Loongson Loongson-3A5000-7A1000-1w-CRB/Loongson-LS3A5000-7A1000-1w-CRB, BIOS vUDK2018-LoongArch-V2.0.pre-beta8 08/18/2022
[ 41.544064] $ 0 : 0000000000000000 90000000011e9468 9000000106c7c000 9000000106c7fcf0
[ 41.552101] $ 4 : 9000000106305d40 9000000106689800 9000000106c7fd08 0000000003995818
[ 41.560138] $ 8 : 0000000000000001 90000000009a72e4 0000000000000020 fffffffffffffffc
[ 41.568174] $12 : 0000000000000000 0000000000000000 0000000000000020 00000009aab7e130
[ 41.576211] $16 : 00000000000001ff 0000000000000407 0000000000000001 0000000000000000
[ 41.584247] $20 : 0000000000000000 0000000000000001 9000000106c7fd70 90000001002f0400
[ 41.592284] $24 : 0000000000000000 900000000178f740 90000000011e9834 90000001063057c0
[ 41.600320] $28 : 0000000000000000 0000000000000001 9000000006826b40 9000000106305140
[ 41.608356] era : 9000000000228848 _save_fp+0x0/0xd8
[ 41.613542] ra : 90000000011e9468 __schedule+0x568/0x8d0
[ 41.619160] CSR crmd: 000000b0
[ 41.619163] CSR prmd: 00000000
[ 41.622359] CSR euen: 00000000
[ 41.625558] CSR ecfg: 00071c1c
[ 41.628756] CSR estat: 000f0000
[ 41.635239] ExcCode : f (SubCode 0)
[ 41.638783] PrId : 0014c010 (Loongson-64bit)
[ 41.643191] Modules linked in: acpi_ipmi vfat fat ipmi_si ipmi_devintf cfg80211 ipmi_msghandler rfkill fuse efivarfs
[ 41.653734] Process iou-wrk-394 (pid: 395, threadinfo=0000000004ebe913, task=00000000636fa1be)
[ 41.662375] Stack : 00000000ffff0875 9000000006800ec0 9000000006800ec0 90000000002d57e0
[ 41.670412] 0000000000000001 0000000000000000 9000000106535880 0000000000000001
[ 41.678450] 9000000105291800 0000000000000000 9000000105291838 900000000178e000
[ 41.686487] 9000000106c7fd90 9000000106305140 0000000000000001 90000000011e9834
[ 41.694523] 00000000ffff0875 90000000011f034c 9000000105291838 9000000105291830
[ 41.702561] 0000000000000000 9000000006801440 00000000ffff0875 90000000002d48c0
[ 41.710597] 9000000128800001 9000000106305140 9000000105291838 9000000105291838
[ 41.718634] 9000000105291830 9000000107811740 9000000105291848 90000000009bf1e0
[ 41.726672] 9000000105291830 9000000107811748 2d6b72772d756f69 0000000000343933
[ 41.734708] 0000000000000000 0000000000000000 0000000000000000 0000000000000000
[ 41.742745] ...
[ 41.745252] Call Trace:
[ 42.197868] [<9000000000228848>] _save_fp+0x0/0xd8
[ 42.205214] [<90000000011ed468>] __schedule+0x568/0x8d0
[ 42.210485] [<90000000011ed834>] schedule+0x64/0xd4
[ 42.215411] [<90000000011f434c>] schedule_timeout+0x88/0x188
[ 42.221115] [<90000000009c36d0>] io_wqe_worker+0x184/0x350
[ 42.226645] [<9000000000221cf0>] ret_from_kernel_thread+0xc/0x9c

This can be easily triggered by ltp testcase syscalls/io_uring02 and it
can also be easily fixed by clearing the FPU/SIMD thread info flags for
kernel threads in copy_thread().

Cc: [email protected]
Reported-by: Qi Hu <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>

show more ...

treewide: use get_random_u32_below() instead of deprecated function

This is a simple mechanical transformation done by:

@@
expression E;
@@
- prandom_u32_max
+ get_random_u32_below
(E)

Reviewed-

treewide: use get_random_u32_below() instead of deprecated function

This is a simple mechanical transformation done by:

@@
expression E;
@@
- prandom_u32_max
+ get_random_u32_below
(E)

Reviewed-by: Kees Cook <[email protected]>
Reviewed-by: Greg Kroah-Hartman <[email protected]>
Acked-by: Darrick J. Wong <[email protected]> # for xfs
Reviewed-by: SeongJae Park <[email protected]> # for damon
Reviewed-by: Jason Gunthorpe <[email protected]> # for infiniband
Reviewed-by: Russell King (Oracle) <[email protected]> # for arm
Acked-by: Ulf Hansson <[email protected]> # for mmc
Signed-off-by: Jason A. Donenfeld <[email protected]>

show more ...

LoongArch: Remove unused kernel stack padding

The current LoongArch kernel stack is padded as if obeying the MIPS o32
calling convention (32 bytes), signifying the port's MIPS lineage but no
longer

LoongArch: Remove unused kernel stack padding

The current LoongArch kernel stack is padded as if obeying the MIPS o32
calling convention (32 bytes), signifying the port's MIPS lineage but no
longer making sense. Remove the padding for clarity.

Reviewed-by: WANG Xuerui <[email protected]>
Signed-off-by: Jinyang He <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>

show more ...

treewide: use prandom_u32_max() when possible, part 1

Rather than incurring a division or requesting too many random bytes for
the given range, use the prandom_u32_max() function, which only takes
t

treewide: use prandom_u32_max() when possible, part 1

Rather than incurring a division or requesting too many random bytes for
the given range, use the prandom_u32_max() function, which only takes
the minimum required bytes from the RNG and avoids divisions. This was
done mechanically with this coccinelle script:

@basic@
expression E;
type T;
identifier get_random_u32 =~ "get_random_int|prandom_u32|get_random_u32";
typedef u64;
@@
(
- ((T)get_random_u32() % (E))
+ prandom_u32_max(E)
|
- ((T)get_random_u32() & ((E) - 1))
+ prandom_u32_max(E * XXX_MAKE_SURE_E_IS_POW2)
|
- ((u64)(E) * get_random_u32() >> 32)
+ prandom_u32_max(E)
|
- ((T)get_random_u32() & ~PAGE_MASK)
+ prandom_u32_max(PAGE_SIZE)
)

@multi_line@
identifier get_random_u32 =~ "get_random_int|prandom_u32|get_random_u32";
identifier RAND;
expression E;
@@

- RAND = get_random_u32();
... when != RAND
- RAND %= (E);
+ RAND = prandom_u32_max(E);

// Find a potential literal
@literal_mask@
expression LITERAL;
type T;
identifier get_random_u32 =~ "get_random_int|prandom_u32|get_random_u32";
position p;
@@

((T)get_random_u32()@p & (LITERAL))

// Add one to the literal.
@script:python add_one@
literal << literal_mask.LITERAL;
RESULT;
@@

value = None
if literal.startswith('0x'):
value = int(literal, 16)
elif literal[0] in '123456789':
value = int(literal, 10)
if value is None:
print("I don't know how to handle %s" % (literal))
cocci.include_match(False)
elif value == 2**32 - 1 or value == 2**31 - 1 or value == 2**24 - 1 or value == 2**16 - 1 or value == 2**8 - 1:
print("Skipping 0x%x for cleanup elsewhere" % (value))
cocci.include_match(False)
elif value & (value + 1) != 0:
print("Skipping 0x%x because it's not a power of two minus one" % (value))
cocci.include_match(False)
elif literal.startswith('0x'):
coccinelle.RESULT = cocci.make_expr("0x%x" % (value + 1))
else:
coccinelle.RESULT = cocci.make_expr("%d" % (value + 1))

// Replace the literal mask with the calculated result.
@plus_one@
expression literal_mask.LITERAL;
position literal_mask.p;
expression add_one.RESULT;
identifier FUNC;
@@

- (FUNC()@p & (LITERAL))
+ prandom_u32_max(RESULT)

@collapse_ret@
type T;
identifier VAR;
expression E;
@@

{
- T VAR;
- VAR = (E);
- return VAR;
+ return E;
}

@drop_var@
type T;
identifier VAR;
@@

{
- T VAR;
... when != VAR
}

Reviewed-by: Greg Kroah-Hartman <[email protected]>
Reviewed-by: Kees Cook <[email protected]>
Reviewed-by: Yury Norov <[email protected]>
Reviewed-by: KP Singh <[email protected]>
Reviewed-by: Jan Kara <[email protected]> # for ext4 and sbitmap
Reviewed-by: Christoph Böhmwalder <[email protected]> # for drbd
Acked-by: Jakub Kicinski <[email protected]>
Acked-by: Heiko Carstens <[email protected]> # for s390
Acked-by: Ulf Hansson <[email protected]> # for mmc
Acked-by: Darrick J. Wong <[email protected]> # for xfs
Signed-off-by: Jason A. Donenfeld <[email protected]>

show more ...

LoongArch: Add STACKTRACE support

1. Use common arch_stack_walk() infrastructure to avoid duplicated code
and avoid taking care of the stack storage and filtering.
2. Add sched_ra (means sched re

LoongArch: Add STACKTRACE support

1. Use common arch_stack_walk() infrastructure to avoid duplicated code
and avoid taking care of the stack storage and filtering.
2. Add sched_ra (means sched return address) and sched_cfa (means sched
call frame address) to thread_info, and store them in switch_to().
3. Add __get_wchan() implementation.

Now we can print the process stack and wait channel by cat /proc/*/stack
and /proc/*/wchan.

Signed-off-by: Qing Zhang <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>

show more ...

LoongArch: Add guess unwinder support

Name "guess unwinder" comes from x86, it scans the stack and reports
every kernel text address it finds.

Unwinders can be used by dump_stack() and other stackt

LoongArch: Add guess unwinder support

Name "guess unwinder" comes from x86, it scans the stack and reports
every kernel text address it finds.

Unwinders can be used by dump_stack() and other stacktrace functions.

Three stages when we do unwind,
1) unwind_start(), the prapare of unwinding, fill unwind_state.
2) unwind_done(), judge whether the unwind process is finished or not.
3) unwind_next_frame(), unwind the next frame.

Add get_stack_info() to get stack info. At present we have irq stack and
task stack. The next_sp is the key info between two types of stacks.

Dividing unwinder helps to add new unwinders in the future.

Signed-off-by: Qing Zhang <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>

show more ...

LoongArch: Fix copy_thread() build errors

Commit c5febea0956fd387 ("fork: Pass struct kernel_clone_args into
copy_thread") change the prototype of copy_thread(), while commit
5bd2e97c868a8a44 ("fork

LoongArch: Fix copy_thread() build errors

Commit c5febea0956fd387 ("fork: Pass struct kernel_clone_args into
copy_thread") change the prototype of copy_thread(), while commit
5bd2e97c868a8a44 ("fork: Generalize PF_IO_WORKER handling") change
the structure of kernel_clone_args. They cause build errors, so fix it.

Fixes: 5bd2e97c868a8a44 ("fork: Generalize PF_IO_WORKER handling")
Fixes: c5febea0956fd387 ("fork: Pass struct kernel_clone_args into copy_thread")
Signed-off-by: Huacai Chen <[email protected]>

show more ...

LoongArch: Add multi-processor (SMP) support

LoongArch-based procesors have 4, 8 or 16 cores per package. This patch
adds multi-processor (SMP) support for LoongArch.

Reviewed-by: WANG Xuerui <git@

LoongArch: Add multi-processor (SMP) support

LoongArch-based procesors have 4, 8 or 16 cores per package. This patch
adds multi-processor (SMP) support for LoongArch.

Reviewed-by: WANG Xuerui <[email protected]>
Reviewed-by: Jiaxun Yang <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>

show more ...

LoongArch: Add process management

Add process management support for LoongArch, including: thread info
definition, context switch and process tracing.

Reviewed-by: WANG Xuerui <[email protected]>
Revi

LoongArch: Add process management

Add process management support for LoongArch, including: thread info
definition, context switch and process tracing.

Reviewed-by: WANG Xuerui <[email protected]>
Reviewed-by: Jiaxun Yang <[email protected]>
Signed-off-by: Huacai Chen <[email protected]>

show more ...