Remove $FreeBSD$: two-line .h pattern

Remove /^\s*\*\n \*\s+\$FreeBSD\$$\n/

spdx: The BSD-2-Clause-FreeBSD identifier is obsolete, drop -FreeBSD

The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of

spdx: The BSD-2-Clause-FreeBSD identifier is obsolete, drop -FreeBSD

The SPDX folks have obsoleted the BSD-2-Clause-FreeBSD identifier. Catch
up to that fact and revert to their recommended match of BSD-2-Clause.

Discussed with: pfg
MFC After: 3 days
Sponsored by: Netflix

show more ...

various: general adoption of SPDX licensing ID tags.

Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error

various: general adoption of SPDX licensing ID tags.

Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.

The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.

No functional change intended.

show more ...

MFC: When ``ppp -direct'' is invoked by a program that uses pipe(2) to
create stdin and stdout, don't blindly try to use stdin as a bi-directional
channel. Instead, detect the pipe and set

MFC: When ``ppp -direct'' is invoked by a program that uses pipe(2) to
create stdin and stdout, don't blindly try to use stdin as a bi-directional
channel. Instead, detect the pipe and set up a special exec handler
that indirects write() calls through stdout.

This fixes the problem where ``set device "!ssh -e none host ppp
-direct label"'' no longer works with an openssh-5.2 server side as
that version of openssh ignores the USE_PIPES config setting and
*always* uses pipes (rather than socketpair) for stdin/stdout channels.

Approved by: re (kib)

show more ...

When ``ppp -direct'' is invoked by a program that uses pipe(2) to
create stdin and stdout, don't blindly try to use stdin as a bi-directional
channel. Instead, detect the pipe and set up a special e

When ``ppp -direct'' is invoked by a program that uses pipe(2) to
create stdin and stdout, don't blindly try to use stdin as a bi-directional
channel. Instead, detect the pipe and set up a special exec handler
that indirects write() calls through stdout.

This fixes the problem where ``set device "!ssh -e none host ppp
-direct label"'' no longer works with an openssh-5.2 server side as
that version of openssh ignores the USE_PIPES config setting and
*always* uses pipes (rather than socketpair) for stdin/stdout channels.

MFC after: 3 days

show more ...

Support PPPoE

Help (lots) from: julian, archie
Facilities from: [email protected]

$Id$ -> $FreeBSD$

Correct the way ppp transfers links on the server side in MP
mode by padding out the ``struct device'' to the maximum
device size.
Bump the ppp version number to indicate the transfer format
change.

Correct the way ppp transfers links on the server side in MP
mode by padding out the ``struct device'' to the maximum
device size.
Bump the ppp version number to indicate the transfer format
change.

This should make MP over tty and udp devices functional again.

show more ...

Allow ``host:port/udp'' devices and support ``host:port/tcp'' as
being the same as the previous (still supported) ``host:port''
syntax for tcp socket devices.

A udp device uses synchronous ppp rathe

Allow ``host:port/udp'' devices and support ``host:port/tcp'' as
being the same as the previous (still supported) ``host:port''
syntax for tcp socket devices.

A udp device uses synchronous ppp rather than async, and avoids
the double-retransmit overhead that comes with ppp over tcp (it's
usually a bad idea to transport IP over a reliable transport that
itself is using an unreliable transport). PPP over UDP provides
througput of ** 1.5Mb per second ** with all compression disabled,
maxing out a PPro/200 when running ppp twice, back-to-back.

This proves that PPPoE is plausable in userland....

This change adds a few more handler functions to struct device and
allows derivations of struct device (which may contain their own
data etc) to pass themselves through the unix domain socket for MP.
** At last **, struct physical has lost all the tty crud !

iov2physical() is now smart enough to restore the correct stack of
layers so that MP servers will work again.

The version number has bumped as our MP link transfer contents have
changed (they now may contain a `struct device').

Don't extract the protocol twice in MP mode (resulting in protocol
rejects for every MP packet). This was broken with my original
layering changes.

Add ``Physical'' and ``Sync'' log levels for logging the relevent
raw packets and add protocol-tracking LogDEBUG stuff in various
LayerPush & LayerPull functions.

Assign our physical device name for incoming tcp connections by
calling getpeername().

Assign our physical device name for incoming udp connections from
the address retrieved by the first recvfrom().

show more ...

o Redesign the layering mechanism and make the aliasing code part of
the layering.

We now ``stack'' layers as soon as we open the device (when we figure
out what we're dealing with). A static

o Redesign the layering mechanism and make the aliasing code part of
the layering.

We now ``stack'' layers as soon as we open the device (when we figure
out what we're dealing with). A static set of `dispatch' routines are
also declared for dealing with incoming packets after they've been
`pulled' up through the stacked layers.

Physical devices are now assigned handlers based on the device type
when they're opened. For the moment there are three device types;
ttys, execs and tcps.

o Increment version number to 2.2
o Make an entry in [uw]tmp for non-tty -direct invocations (after
pap/chap authentication).
o Make throughput counters quad_t's
o Account for the absolute number of mbuf malloc()s and free()s in
``show mem''.
o ``show modem'' becomes ``show physical''.

show more ...