sys: Remove $FreeBSD$: one-line sh pattern

Remove /^\s*#[#!]?\s*\$FreeBSD\$.*$\n/

Fix some modules to export more used symbols

and remove non-present symbols that are now reported by kmod_syms.awk.

Reviewed by: emaste
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differ

Fix some modules to export more used symbols

and remove non-present symbols that are now reported by kmod_syms.awk.

Reviewed by: emaste
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D32878

show more ...

bhnd(4): extend the PMU APIs to support bwn(4)

The bwn(4) driver requires a number of extensions to the bhnd(4) PMU
interface to support external configuration of PLLs, LDOs, and other
parameters th

bhnd(4): extend the PMU APIs to support bwn(4)

The bwn(4) driver requires a number of extensions to the bhnd(4) PMU
interface to support external configuration of PLLs, LDOs, and other
parameters that require chipset or PHY-specific workarounds.

These changes add support for:

- Writing raw voltage register values to PHY-specific LDO regulator
registers (required by LP-PHY).
- Enabling/disabling PHY-specific LDOs (required by LP-PHY)
- Writing to arbitrary PMU chipctrl registers (required for common PHY PLL
reset support).
- Requesting chipset/PLL-specific spurious signal avoidance modes.
- Querying clock frequency and latency.

Additionally, rather than updating legacy PWRCTL support to conform to the
new PMU interface:

- PWRCTL API is now provided by a bhnd_pwrctl_if.m interface.
- Since PWRCTL is only found in older SSB-based chipsets, translation from
bhnd(4) bus APIs to corresponding PWRCTL operations is now handled
entirely within the siba(4) driver.
- The PWRCTL-specific host bridge clock gating APIs in bhnd_bus_if.m have
been lifted out into a standalone bhnd_pwrctl_hostb_if.m interface.

Approved by: adrian (mentor, implicit)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D12664

show more ...

sys/modules: normalize .CURDIR-relative paths to SRCTOP

This simplifies make output/logic

Tested with: `cd sys/modules; make ALL_MODULES=` on amd64
MFC after: 1 month
Sponsored by: Dell EMC Isilon

Revert r308107

Requested by: jhb

- Fix `make` in sys/modules/bhnd

Approved by: landonf
Differential Revision: https://reviews.freebsd.org/D7774

Migrate bhndb(4) to the new bhnd_erom API.

Adds support for probing and initializing bhndb(4) bridge state using
the bhnd_erom API, ensuring that full bridge configuration is available
*prior* to ac

Migrate bhndb(4) to the new bhnd_erom API.

Adds support for probing and initializing bhndb(4) bridge state using
the bhnd_erom API, ensuring that full bridge configuration is available
*prior* to actually attaching and enumerating the bhnd(4) child device,
allowing us to safely allocate bus-level agent/device resources during
bhnd(4) bus enumeration.

- Add a bhnd_erom_probe() method usable by bhndb(4). This is an analogue
to the existing bhnd_erom_probe_static() method, and allows the bhndb
bridge to discover the best available erom parser class prior to newbus
probing of its children.
- Add support for supplying identification hints when probing erom
devices. This is required on early EXTIF-only chipsets, where chip
identification registers are not available.
- Migrate bhndb over to the new bhnd_erom API, using bhnd_core_info
records rather than bridged bhnd(4) device_t references to determine
the bridged chipsets' capability/bridge configuration.
- The bhndb parent (e.g. if_bwn) is now required to supply a hardware
priority table to the bridge. The default table is currently sufficient
for our supported devices.
- Drop the two-pass attach approach we used for compatibility with bhndb(4) in
the bhnd(4) bus drivers, and instead perform bus enumeration immediately,
and allocate bridged per-child bus-level resources during that enumeration.

Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D7768

show more ...

[bhnd] Add support for querying the attachment type of the bhnd bus.

This adds a BHND_BUS_GET_ATTACH_TYPE(); the primary use-case is to let
chipc make a coarse-grained determination as to whether UA

[bhnd] Add support for querying the attachment type of the bhnd bus.

This adds a BHND_BUS_GET_ATTACH_TYPE(); the primary use-case is to let
chipc make a coarse-grained determination as to whether UART, SPI, etc
drivers ought to be attached, and on fullmac devices, whether a real
CPU driver ought to be skipped for the ARM core, etc.

Tested:

* BCM4331 (BHND)
* BCM4312 (SIBA)

Submitted by: Landon Fuller <[email protected]>
Differential Revision: https://reviews.freebsd.org/D6492

show more ...

[bhnd] Initial bhnd(4) SPROM/NVRAM support.

This adds support for the NVRAM handling and the basic SPROM
hardware used on siba(4) and bcma(4) devices, including:

* SPROM directly attached to the PC

[bhnd] Initial bhnd(4) SPROM/NVRAM support.

This adds support for the NVRAM handling and the basic SPROM
hardware used on siba(4) and bcma(4) devices, including:

* SPROM directly attached to the PCI core, accessible via PCI configuration
space.
* SPROM attached to later ChipCommon cores.
* SPROM variables vended from the parent SoC bus (e.g. via a directly-attached
flash device).

Additional improvements to the NVRAM/SPROM interface will
be required, but this changeset stands alone as working
checkpoint.

Submitted by: Landon Fuller <[email protected]>
Reviewed by: Michael Zhilin <[email protected]> (Broadcom MIPS support)
Differential Revision: https://reviews.freebsd.org/D6196

show more ...

[bhnd] add missing bus file.

[bhnd] add missing bus interface SRC bits, required after the last source import.

Add modules support for the bhnd code.

Submitted by: Landon Fuller <[email protected]>
Obtained from: https://github.com/landonf/freebsd/compare/user/landonf/bcm4331-CURRENT