1 #ifndef NETDEV_PCS_H 2 #define NETDEV_PCS_H 3 4 #include <linux/phy.h> 5 #include <linux/spinlock.h> 6 #include <linux/workqueue.h> 7 8 struct device_node; 9 struct ethtool_cmd; 10 struct fwnode_handle; 11 struct net_device; 12 struct phylink; 13 14 enum { 15 MLO_PAUSE_NONE, 16 MLO_PAUSE_RX = BIT(0), 17 MLO_PAUSE_TX = BIT(1), 18 MLO_PAUSE_TXRX_MASK = MLO_PAUSE_TX | MLO_PAUSE_RX, 19 MLO_PAUSE_AN = BIT(2), 20 21 MLO_AN_PHY = 0, /* Conventional PHY */ 22 MLO_AN_FIXED, /* Fixed-link mode */ 23 MLO_AN_INBAND, /* In-band protocol */ 24 25 /* PCS "negotiation" mode. 26 * PHYLINK_PCS_NEG_NONE - protocol has no inband capability 27 * PHYLINK_PCS_NEG_OUTBAND - some out of band or fixed link setting 28 * PHYLINK_PCS_NEG_INBAND_DISABLED - inband mode disabled, e.g. 29 * 1000base-X with autoneg off 30 * PHYLINK_PCS_NEG_INBAND_ENABLED - inband mode enabled 31 * Additionally, this can be tested using bitmasks: 32 * PHYLINK_PCS_NEG_INBAND - inband mode selected 33 * PHYLINK_PCS_NEG_ENABLED - negotiation mode enabled 34 */ 35 PHYLINK_PCS_NEG_NONE = 0, 36 PHYLINK_PCS_NEG_ENABLED = BIT(4), 37 PHYLINK_PCS_NEG_OUTBAND = BIT(5), 38 PHYLINK_PCS_NEG_INBAND = BIT(6), 39 PHYLINK_PCS_NEG_INBAND_DISABLED = PHYLINK_PCS_NEG_INBAND, 40 PHYLINK_PCS_NEG_INBAND_ENABLED = PHYLINK_PCS_NEG_INBAND | 41 PHYLINK_PCS_NEG_ENABLED, 42 43 /* MAC_SYM_PAUSE and MAC_ASYM_PAUSE are used when configuring our 44 * autonegotiation advertisement. They correspond to the PAUSE and 45 * ASM_DIR bits defined by 802.3, respectively. 46 * 47 * The following table lists the values of tx_pause and rx_pause which 48 * might be requested in mac_link_up. The exact values depend on either 49 * the results of autonegotation (if MLO_PAUSE_AN is set) or user 50 * configuration (if MLO_PAUSE_AN is not set). 51 * 52 * MAC_SYM_PAUSE MAC_ASYM_PAUSE MLO_PAUSE_AN tx_pause/rx_pause 53 * ============= ============== ============ ================== 54 * 0 0 0 0/0 55 * 0 0 1 0/0 56 * 0 1 0 0/0, 0/1, 1/0, 1/1 57 * 0 1 1 0/0, 1/0 58 * 1 0 0 0/0, 1/1 59 * 1 0 1 0/0, 1/1 60 * 1 1 0 0/0, 0/1, 1/0, 1/1 61 * 1 1 1 0/0, 0/1, 1/1 62 * 63 * If you set MAC_ASYM_PAUSE, the user may request any combination of 64 * tx_pause and rx_pause. You do not have to support these 65 * combinations. 66 * 67 * However, you should support combinations of tx_pause and rx_pause 68 * which might be the result of autonegotation. For example, don't set 69 * MAC_SYM_PAUSE unless your device can support tx_pause and rx_pause 70 * at the same time. 71 */ 72 MAC_SYM_PAUSE = BIT(0), 73 MAC_ASYM_PAUSE = BIT(1), 74 MAC_10HD = BIT(2), 75 MAC_10FD = BIT(3), 76 MAC_10 = MAC_10HD | MAC_10FD, 77 MAC_100HD = BIT(4), 78 MAC_100FD = BIT(5), 79 MAC_100 = MAC_100HD | MAC_100FD, 80 MAC_1000HD = BIT(6), 81 MAC_1000FD = BIT(7), 82 MAC_1000 = MAC_1000HD | MAC_1000FD, 83 MAC_2500FD = BIT(8), 84 MAC_5000FD = BIT(9), 85 MAC_10000FD = BIT(10), 86 MAC_20000FD = BIT(11), 87 MAC_25000FD = BIT(12), 88 MAC_40000FD = BIT(13), 89 MAC_50000FD = BIT(14), 90 MAC_56000FD = BIT(15), 91 MAC_100000FD = BIT(16), 92 MAC_200000FD = BIT(17), 93 MAC_400000FD = BIT(18), 94 }; 95 96 static inline bool phylink_autoneg_inband(unsigned int mode) 97 { 98 return mode == MLO_AN_INBAND; 99 } 100 101 /** 102 * phylink_pcs_neg_mode() - helper to determine PCS inband mode 103 * @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND. 104 * @interface: interface mode to be used 105 * @advertising: adertisement ethtool link mode mask 106 * 107 * Determines the negotiation mode to be used by the PCS, and returns 108 * one of: 109 * 110 * - %PHYLINK_PCS_NEG_NONE: interface mode does not support inband 111 * - %PHYLINK_PCS_NEG_OUTBAND: an out of band mode (e.g. reading the PHY) 112 * will be used. 113 * - %PHYLINK_PCS_NEG_INBAND_DISABLED: inband mode selected but autoneg 114 * disabled 115 * - %PHYLINK_PCS_NEG_INBAND_ENABLED: inband mode selected and autoneg enabled 116 * 117 * Note: this is for cases where the PCS itself is involved in negotiation 118 * (e.g. Clause 37, SGMII and similar) not Clause 73. 119 */ 120 static inline unsigned int phylink_pcs_neg_mode(unsigned int mode, 121 phy_interface_t interface, 122 const unsigned long *advertising) 123 { 124 unsigned int neg_mode; 125 126 switch (interface) { 127 case PHY_INTERFACE_MODE_SGMII: 128 case PHY_INTERFACE_MODE_QSGMII: 129 case PHY_INTERFACE_MODE_QUSGMII: 130 case PHY_INTERFACE_MODE_USXGMII: 131 /* These protocols are designed for use with a PHY which 132 * communicates its negotiation result back to the MAC via 133 * inband communication. Note: there exist PHYs that run 134 * with SGMII but do not send the inband data. 135 */ 136 if (!phylink_autoneg_inband(mode)) 137 neg_mode = PHYLINK_PCS_NEG_OUTBAND; 138 else 139 neg_mode = PHYLINK_PCS_NEG_INBAND_ENABLED; 140 break; 141 142 case PHY_INTERFACE_MODE_1000BASEX: 143 case PHY_INTERFACE_MODE_2500BASEX: 144 /* 1000base-X is designed for use media-side for Fibre 145 * connections, and thus the Autoneg bit needs to be 146 * taken into account. We also do this for 2500base-X 147 * as well, but drivers may not support this, so may 148 * need to override this. 149 */ 150 if (!phylink_autoneg_inband(mode)) 151 neg_mode = PHYLINK_PCS_NEG_OUTBAND; 152 else if (linkmode_test_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, 153 advertising)) 154 neg_mode = PHYLINK_PCS_NEG_INBAND_ENABLED; 155 else 156 neg_mode = PHYLINK_PCS_NEG_INBAND_DISABLED; 157 break; 158 159 default: 160 neg_mode = PHYLINK_PCS_NEG_NONE; 161 break; 162 } 163 164 return neg_mode; 165 } 166 167 /** 168 * struct phylink_link_state - link state structure 169 * @advertising: ethtool bitmask containing advertised link modes 170 * @lp_advertising: ethtool bitmask containing link partner advertised link 171 * modes 172 * @interface: link &typedef phy_interface_t mode 173 * @speed: link speed, one of the SPEED_* constants. 174 * @duplex: link duplex mode, one of DUPLEX_* constants. 175 * @pause: link pause state, described by MLO_PAUSE_* constants. 176 * @rate_matching: rate matching being performed, one of the RATE_MATCH_* 177 * constants. If rate matching is taking place, then the speed/duplex of 178 * the medium link mode (@speed and @duplex) and the speed/duplex of the phy 179 * interface mode (@interface) are different. 180 * @link: true if the link is up. 181 * @an_complete: true if autonegotiation has completed. 182 */ 183 struct phylink_link_state { 184 __ETHTOOL_DECLARE_LINK_MODE_MASK(advertising); 185 __ETHTOOL_DECLARE_LINK_MODE_MASK(lp_advertising); 186 phy_interface_t interface; 187 int speed; 188 int duplex; 189 int pause; 190 int rate_matching; 191 unsigned int link:1; 192 unsigned int an_complete:1; 193 }; 194 195 enum phylink_op_type { 196 PHYLINK_NETDEV = 0, 197 PHYLINK_DEV, 198 }; 199 200 /** 201 * struct phylink_config - PHYLINK configuration structure 202 * @dev: a pointer to a struct device associated with the MAC 203 * @type: operation type of PHYLINK instance 204 * @poll_fixed_state: if true, starts link_poll, 205 * if MAC link is at %MLO_AN_FIXED mode. 206 * @mac_managed_pm: if true, indicate the MAC driver is responsible for PHY PM. 207 * @ovr_an_inband: if true, override PCS to MLO_AN_INBAND 208 * @get_fixed_state: callback to execute to determine the fixed link state, 209 * if MAC link is at %MLO_AN_FIXED mode. 210 * @supported_interfaces: bitmap describing which PHY_INTERFACE_MODE_xxx 211 * are supported by the MAC/PCS. 212 * @mac_capabilities: MAC pause/speed/duplex capabilities. 213 */ 214 struct phylink_config { 215 struct device *dev; 216 enum phylink_op_type type; 217 bool poll_fixed_state; 218 bool mac_managed_pm; 219 bool ovr_an_inband; 220 void (*get_fixed_state)(struct phylink_config *config, 221 struct phylink_link_state *state); 222 DECLARE_PHY_INTERFACE_MASK(supported_interfaces); 223 unsigned long mac_capabilities; 224 }; 225 226 /** 227 * struct phylink_mac_ops - MAC operations structure. 228 * @validate: Validate and update the link configuration. 229 * @mac_select_pcs: Select a PCS for the interface mode. 230 * @mac_prepare: prepare for a major reconfiguration of the interface. 231 * @mac_config: configure the MAC for the selected mode and state. 232 * @mac_finish: finish a major reconfiguration of the interface. 233 * @mac_link_down: take the link down. 234 * @mac_link_up: allow the link to come up. 235 * 236 * The individual methods are described more fully below. 237 */ 238 struct phylink_mac_ops { 239 void (*validate)(struct phylink_config *config, 240 unsigned long *supported, 241 struct phylink_link_state *state); 242 struct phylink_pcs *(*mac_select_pcs)(struct phylink_config *config, 243 phy_interface_t interface); 244 int (*mac_prepare)(struct phylink_config *config, unsigned int mode, 245 phy_interface_t iface); 246 void (*mac_config)(struct phylink_config *config, unsigned int mode, 247 const struct phylink_link_state *state); 248 int (*mac_finish)(struct phylink_config *config, unsigned int mode, 249 phy_interface_t iface); 250 void (*mac_link_down)(struct phylink_config *config, unsigned int mode, 251 phy_interface_t interface); 252 void (*mac_link_up)(struct phylink_config *config, 253 struct phy_device *phy, unsigned int mode, 254 phy_interface_t interface, int speed, int duplex, 255 bool tx_pause, bool rx_pause); 256 }; 257 258 #if 0 /* For kernel-doc purposes only. */ 259 /** 260 * validate - Validate and update the link configuration 261 * @config: a pointer to a &struct phylink_config. 262 * @supported: ethtool bitmask for supported link modes. 263 * @state: a pointer to a &struct phylink_link_state. 264 * 265 * Clear bits in the @supported and @state->advertising masks that 266 * are not supportable by the MAC. 267 * 268 * Note that the PHY may be able to transform from one connection 269 * technology to another, so, eg, don't clear 1000BaseX just 270 * because the MAC is unable to BaseX mode. This is more about 271 * clearing unsupported speeds and duplex settings. The port modes 272 * should not be cleared; phylink_set_port_modes() will help with this. 273 * 274 * When @config->supported_interfaces has been set, phylink will iterate 275 * over the supported interfaces to determine the full capability of the 276 * MAC. The validation function must not print errors if @state->interface 277 * is set to an unexpected value. 278 * 279 * When @config->supported_interfaces is empty, phylink will call this 280 * function with @state->interface set to %PHY_INTERFACE_MODE_NA, and 281 * expects the MAC driver to return all supported link modes. 282 * 283 * If the @state->interface mode is not supported, then the @supported 284 * mask must be cleared. 285 * 286 * This member is optional; if not set, the generic validator will be 287 * used making use of @config->mac_capabilities and 288 * @config->supported_interfaces to determine which link modes are 289 * supported. 290 */ 291 void validate(struct phylink_config *config, unsigned long *supported, 292 struct phylink_link_state *state); 293 /** 294 * mac_select_pcs: Select a PCS for the interface mode. 295 * @config: a pointer to a &struct phylink_config. 296 * @interface: PHY interface mode for PCS 297 * 298 * Return the &struct phylink_pcs for the specified interface mode, or 299 * NULL if none is required, or an error pointer on error. 300 * 301 * This must not modify any state. It is used to query which PCS should 302 * be used. Phylink will use this during validation to ensure that the 303 * configuration is valid, and when setting a configuration to internally 304 * set the PCS that will be used. 305 */ 306 struct phylink_pcs *mac_select_pcs(struct phylink_config *config, 307 phy_interface_t interface); 308 309 /** 310 * mac_prepare() - prepare to change the PHY interface mode 311 * @config: a pointer to a &struct phylink_config. 312 * @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND. 313 * @iface: interface mode to switch to 314 * 315 * phylink will call this method at the beginning of a full initialisation 316 * of the link, which includes changing the interface mode or at initial 317 * startup time. It may be called for the current mode. The MAC driver 318 * should perform whatever actions are required, e.g. disabling the 319 * Serdes PHY. 320 * 321 * This will be the first call in the sequence: 322 * - mac_prepare() 323 * - mac_config() 324 * - pcs_config() 325 * - possible pcs_an_restart() 326 * - mac_finish() 327 * 328 * Returns zero on success, or negative errno on failure which will be 329 * reported to the kernel log. 330 */ 331 int mac_prepare(struct phylink_config *config, unsigned int mode, 332 phy_interface_t iface); 333 334 /** 335 * mac_config() - configure the MAC for the selected mode and state 336 * @config: a pointer to a &struct phylink_config. 337 * @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND. 338 * @state: a pointer to a &struct phylink_link_state. 339 * 340 * Note - not all members of @state are valid. In particular, 341 * @state->lp_advertising, @state->link, @state->an_complete are never 342 * guaranteed to be correct, and so any mac_config() implementation must 343 * never reference these fields. 344 * 345 * This will only be called to reconfigure the MAC for a "major" change in 346 * e.g. interface mode. It will not be called for changes in speed, duplex 347 * or pause modes or to change the in-band advertisement. 348 * 349 * In all negotiation modes, as defined by @mode, @state->pause indicates the 350 * pause settings which should be applied as follows. If %MLO_PAUSE_AN is not 351 * set, %MLO_PAUSE_TX and %MLO_PAUSE_RX indicate whether the MAC should send 352 * pause frames and/or act on received pause frames respectively. Otherwise, 353 * the results of in-band negotiation/status from the MAC PCS should be used 354 * to control the MAC pause mode settings. 355 * 356 * The action performed depends on the currently selected mode: 357 * 358 * %MLO_AN_FIXED, %MLO_AN_PHY: 359 * Configure for non-inband negotiation mode, where the link settings 360 * are completely communicated via mac_link_up(). The physical link 361 * protocol from the MAC is specified by @state->interface. 362 * 363 * @state->advertising may be used, but is not required. 364 * 365 * Older drivers (prior to the mac_link_up() change) may use @state->speed, 366 * @state->duplex and @state->pause to configure the MAC, but this is 367 * deprecated; such drivers should be converted to use mac_link_up(). 368 * 369 * Other members of @state must be ignored. 370 * 371 * Valid state members: interface, advertising. 372 * Deprecated state members: speed, duplex, pause. 373 * 374 * %MLO_AN_INBAND: 375 * place the link in an inband negotiation mode (such as 802.3z 376 * 1000base-X or Cisco SGMII mode depending on the @state->interface 377 * mode). In both cases, link state management (whether the link 378 * is up or not) is performed by the MAC, and reported via the 379 * pcs_get_state() callback. Changes in link state must be made 380 * by calling phylink_mac_change(). 381 * 382 * Interface mode specific details are mentioned below. 383 * 384 * If in 802.3z mode, the link speed is fixed, dependent on the 385 * @state->interface. Duplex and pause modes are negotiated via 386 * the in-band configuration word. Advertised pause modes are set 387 * according to the @state->an_enabled and @state->advertising 388 * flags. Beware of MACs which only support full duplex at gigabit 389 * and higher speeds. 390 * 391 * If in Cisco SGMII mode, the link speed and duplex mode are passed 392 * in the serial bitstream 16-bit configuration word, and the MAC 393 * should be configured to read these bits and acknowledge the 394 * configuration word. Nothing is advertised by the MAC. The MAC is 395 * responsible for reading the configuration word and configuring 396 * itself accordingly. 397 * 398 * Valid state members: interface, an_enabled, pause, advertising. 399 * 400 * Implementations are expected to update the MAC to reflect the 401 * requested settings - i.o.w., if nothing has changed between two 402 * calls, no action is expected. If only flow control settings have 403 * changed, flow control should be updated *without* taking the link 404 * down. This "update" behaviour is critical to avoid bouncing the 405 * link up status. 406 */ 407 void mac_config(struct phylink_config *config, unsigned int mode, 408 const struct phylink_link_state *state); 409 410 /** 411 * mac_finish() - finish a to change the PHY interface mode 412 * @config: a pointer to a &struct phylink_config. 413 * @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND. 414 * @iface: interface mode to switch to 415 * 416 * phylink will call this if it called mac_prepare() to allow the MAC to 417 * complete any necessary steps after the MAC and PCS have been configured 418 * for the @mode and @iface. E.g. a MAC driver may wish to re-enable the 419 * Serdes PHY here if it was previously disabled by mac_prepare(). 420 * 421 * Returns zero on success, or negative errno on failure which will be 422 * reported to the kernel log. 423 */ 424 int mac_finish(struct phylink_config *config, unsigned int mode, 425 phy_interface_t iface); 426 427 /** 428 * mac_link_down() - take the link down 429 * @config: a pointer to a &struct phylink_config. 430 * @mode: link autonegotiation mode 431 * @interface: link &typedef phy_interface_t mode 432 * 433 * If @mode is not an in-band negotiation mode (as defined by 434 * phylink_autoneg_inband()), force the link down and disable any 435 * Energy Efficient Ethernet MAC configuration. Interface type 436 * selection must be done in mac_config(). 437 */ 438 void mac_link_down(struct phylink_config *config, unsigned int mode, 439 phy_interface_t interface); 440 441 /** 442 * mac_link_up() - allow the link to come up 443 * @config: a pointer to a &struct phylink_config. 444 * @phy: any attached phy 445 * @mode: link autonegotiation mode 446 * @interface: link &typedef phy_interface_t mode 447 * @speed: link speed 448 * @duplex: link duplex 449 * @tx_pause: link transmit pause enablement status 450 * @rx_pause: link receive pause enablement status 451 * 452 * Configure the MAC for an established link. 453 * 454 * @speed, @duplex, @tx_pause and @rx_pause indicate the finalised link 455 * settings, and should be used to configure the MAC block appropriately 456 * where these settings are not automatically conveyed from the PCS block, 457 * or if in-band negotiation (as defined by phylink_autoneg_inband(@mode)) 458 * is disabled. 459 * 460 * Note that when 802.3z in-band negotiation is in use, it is possible 461 * that the user wishes to override the pause settings, and this should 462 * be allowed when considering the implementation of this method. 463 * 464 * If in-band negotiation mode is disabled, allow the link to come up. If 465 * @phy is non-%NULL, configure Energy Efficient Ethernet by calling 466 * phy_init_eee() and perform appropriate MAC configuration for EEE. 467 * Interface type selection must be done in mac_config(). 468 */ 469 void mac_link_up(struct phylink_config *config, struct phy_device *phy, 470 unsigned int mode, phy_interface_t interface, 471 int speed, int duplex, bool tx_pause, bool rx_pause); 472 #endif 473 474 struct phylink_pcs_ops; 475 476 /** 477 * struct phylink_pcs - PHYLINK PCS instance 478 * @ops: a pointer to the &struct phylink_pcs_ops structure 479 * @phylink: pointer to &struct phylink_config 480 * @neg_mode: provide PCS neg mode via "mode" argument 481 * @poll: poll the PCS for link changes 482 * 483 * This structure is designed to be embedded within the PCS private data, 484 * and will be passed between phylink and the PCS. 485 * 486 * The @phylink member is private to phylink and must not be touched by 487 * the PCS driver. 488 */ 489 struct phylink_pcs { 490 const struct phylink_pcs_ops *ops; 491 struct phylink *phylink; 492 bool neg_mode; 493 bool poll; 494 }; 495 496 /** 497 * struct phylink_pcs_ops - MAC PCS operations structure. 498 * @pcs_validate: validate the link configuration. 499 * @pcs_enable: enable the PCS. 500 * @pcs_disable: disable the PCS. 501 * @pcs_pre_config: pre-mac_config method (for errata) 502 * @pcs_post_config: post-mac_config method (for arrata) 503 * @pcs_get_state: read the current MAC PCS link state from the hardware. 504 * @pcs_config: configure the MAC PCS for the selected mode and state. 505 * @pcs_an_restart: restart 802.3z BaseX autonegotiation. 506 * @pcs_link_up: program the PCS for the resolved link configuration 507 * (where necessary). 508 */ 509 struct phylink_pcs_ops { 510 int (*pcs_validate)(struct phylink_pcs *pcs, unsigned long *supported, 511 const struct phylink_link_state *state); 512 int (*pcs_enable)(struct phylink_pcs *pcs); 513 void (*pcs_disable)(struct phylink_pcs *pcs); 514 void (*pcs_pre_config)(struct phylink_pcs *pcs, 515 phy_interface_t interface); 516 int (*pcs_post_config)(struct phylink_pcs *pcs, 517 phy_interface_t interface); 518 void (*pcs_get_state)(struct phylink_pcs *pcs, 519 struct phylink_link_state *state); 520 int (*pcs_config)(struct phylink_pcs *pcs, unsigned int neg_mode, 521 phy_interface_t interface, 522 const unsigned long *advertising, 523 bool permit_pause_to_mac); 524 void (*pcs_an_restart)(struct phylink_pcs *pcs); 525 void (*pcs_link_up)(struct phylink_pcs *pcs, unsigned int neg_mode, 526 phy_interface_t interface, int speed, int duplex); 527 }; 528 529 #if 0 /* For kernel-doc purposes only. */ 530 /** 531 * pcs_validate() - validate the link configuration. 532 * @pcs: a pointer to a &struct phylink_pcs. 533 * @supported: ethtool bitmask for supported link modes. 534 * @state: a const pointer to a &struct phylink_link_state. 535 * 536 * Validate the interface mode, and advertising's autoneg bit, removing any 537 * media ethtool link modes that would not be supportable from the supported 538 * mask. Phylink will propagate the changes to the advertising mask. See the 539 * &struct phylink_mac_ops validate() method. 540 * 541 * Returns -EINVAL if the interface mode/autoneg mode is not supported. 542 * Returns non-zero positive if the link state can be supported. 543 */ 544 int pcs_validate(struct phylink_pcs *pcs, unsigned long *supported, 545 const struct phylink_link_state *state); 546 547 /** 548 * pcs_enable() - enable the PCS. 549 * @pcs: a pointer to a &struct phylink_pcs. 550 */ 551 int pcs_enable(struct phylink_pcs *pcs); 552 553 /** 554 * pcs_disable() - disable the PCS. 555 * @pcs: a pointer to a &struct phylink_pcs. 556 */ 557 void pcs_disable(struct phylink_pcs *pcs); 558 559 /** 560 * pcs_get_state() - Read the current inband link state from the hardware 561 * @pcs: a pointer to a &struct phylink_pcs. 562 * @state: a pointer to a &struct phylink_link_state. 563 * 564 * Read the current inband link state from the MAC PCS, reporting the 565 * current speed in @state->speed, duplex mode in @state->duplex, pause 566 * mode in @state->pause using the %MLO_PAUSE_RX and %MLO_PAUSE_TX bits, 567 * negotiation completion state in @state->an_complete, and link up state 568 * in @state->link. If possible, @state->lp_advertising should also be 569 * populated. 570 * 571 * When present, this overrides pcs_get_state() in &struct 572 * phylink_pcs_ops. 573 */ 574 void pcs_get_state(struct phylink_pcs *pcs, 575 struct phylink_link_state *state); 576 577 /** 578 * pcs_config() - Configure the PCS mode and advertisement 579 * @pcs: a pointer to a &struct phylink_pcs. 580 * @neg_mode: link negotiation mode (see below) 581 * @interface: interface mode to be used 582 * @advertising: adertisement ethtool link mode mask 583 * @permit_pause_to_mac: permit forwarding pause resolution to MAC 584 * 585 * Configure the PCS for the operating mode, the interface mode, and set 586 * the advertisement mask. @permit_pause_to_mac indicates whether the 587 * hardware may forward the pause mode resolution to the MAC. 588 * 589 * When operating in %MLO_AN_INBAND, inband should always be enabled, 590 * otherwise inband should be disabled. 591 * 592 * For SGMII, there is no advertisement from the MAC side, the PCS should 593 * be programmed to acknowledge the inband word from the PHY. 594 * 595 * For 1000BASE-X, the advertisement should be programmed into the PCS. 596 * 597 * For most 10GBASE-R, there is no advertisement. 598 * 599 * The %neg_mode argument should be tested via the phylink_mode_*() family of 600 * functions, or for PCS that set pcs->neg_mode true, should be tested 601 * against the %PHYLINK_PCS_NEG_* definitions. 602 */ 603 int pcs_config(struct phylink_pcs *pcs, unsigned int neg_mode, 604 phy_interface_t interface, const unsigned long *advertising, 605 bool permit_pause_to_mac); 606 607 /** 608 * pcs_an_restart() - restart 802.3z BaseX autonegotiation 609 * @pcs: a pointer to a &struct phylink_pcs. 610 * 611 * When PCS ops are present, this overrides mac_an_restart() in &struct 612 * phylink_mac_ops. 613 */ 614 void pcs_an_restart(struct phylink_pcs *pcs); 615 616 /** 617 * pcs_link_up() - program the PCS for the resolved link configuration 618 * @pcs: a pointer to a &struct phylink_pcs. 619 * @neg_mode: link negotiation mode (see below) 620 * @interface: link &typedef phy_interface_t mode 621 * @speed: link speed 622 * @duplex: link duplex 623 * 624 * This call will be made just before mac_link_up() to inform the PCS of 625 * the resolved link parameters. For example, a PCS operating in SGMII 626 * mode without in-band AN needs to be manually configured for the link 627 * and duplex setting. Otherwise, this should be a no-op. 628 * 629 * The %mode argument should be tested via the phylink_mode_*() family of 630 * functions, or for PCS that set pcs->neg_mode true, should be tested 631 * against the %PHYLINK_PCS_NEG_* definitions. 632 */ 633 void pcs_link_up(struct phylink_pcs *pcs, unsigned int neg_mode, 634 phy_interface_t interface, int speed, int duplex); 635 #endif 636 637 void phylink_caps_to_linkmodes(unsigned long *linkmodes, unsigned long caps); 638 unsigned long phylink_get_capabilities(phy_interface_t interface, 639 unsigned long mac_capabilities, 640 int rate_matching); 641 void phylink_validate_mask_caps(unsigned long *supported, 642 struct phylink_link_state *state, 643 unsigned long caps); 644 void phylink_generic_validate(struct phylink_config *config, 645 unsigned long *supported, 646 struct phylink_link_state *state); 647 648 struct phylink *phylink_create(struct phylink_config *, 649 const struct fwnode_handle *, 650 phy_interface_t, 651 const struct phylink_mac_ops *); 652 void phylink_destroy(struct phylink *); 653 bool phylink_expects_phy(struct phylink *pl); 654 655 int phylink_connect_phy(struct phylink *, struct phy_device *); 656 int phylink_of_phy_connect(struct phylink *, struct device_node *, u32 flags); 657 int phylink_fwnode_phy_connect(struct phylink *pl, 658 const struct fwnode_handle *fwnode, 659 u32 flags); 660 void phylink_disconnect_phy(struct phylink *); 661 662 void phylink_mac_change(struct phylink *, bool up); 663 void phylink_pcs_change(struct phylink_pcs *, bool up); 664 665 void phylink_start(struct phylink *); 666 void phylink_stop(struct phylink *); 667 668 void phylink_suspend(struct phylink *pl, bool mac_wol); 669 void phylink_resume(struct phylink *pl); 670 671 void phylink_ethtool_get_wol(struct phylink *, struct ethtool_wolinfo *); 672 int phylink_ethtool_set_wol(struct phylink *, struct ethtool_wolinfo *); 673 674 int phylink_ethtool_ksettings_get(struct phylink *, 675 struct ethtool_link_ksettings *); 676 int phylink_ethtool_ksettings_set(struct phylink *, 677 const struct ethtool_link_ksettings *); 678 int phylink_ethtool_nway_reset(struct phylink *); 679 void phylink_ethtool_get_pauseparam(struct phylink *, 680 struct ethtool_pauseparam *); 681 int phylink_ethtool_set_pauseparam(struct phylink *, 682 struct ethtool_pauseparam *); 683 int phylink_get_eee_err(struct phylink *); 684 int phylink_init_eee(struct phylink *, bool); 685 int phylink_ethtool_get_eee(struct phylink *, struct ethtool_eee *); 686 int phylink_ethtool_set_eee(struct phylink *, struct ethtool_eee *); 687 int phylink_mii_ioctl(struct phylink *, struct ifreq *, int); 688 int phylink_speed_down(struct phylink *pl, bool sync); 689 int phylink_speed_up(struct phylink *pl); 690 691 #define phylink_zero(bm) \ 692 bitmap_zero(bm, __ETHTOOL_LINK_MODE_MASK_NBITS) 693 #define __phylink_do_bit(op, bm, mode) \ 694 op(ETHTOOL_LINK_MODE_ ## mode ## _BIT, bm) 695 696 #define phylink_set(bm, mode) __phylink_do_bit(__set_bit, bm, mode) 697 #define phylink_clear(bm, mode) __phylink_do_bit(__clear_bit, bm, mode) 698 #define phylink_test(bm, mode) __phylink_do_bit(test_bit, bm, mode) 699 700 void phylink_set_port_modes(unsigned long *bits); 701 702 /** 703 * phylink_get_link_timer_ns - return the PCS link timer value 704 * @interface: link &typedef phy_interface_t mode 705 * 706 * Return the PCS link timer setting in nanoseconds for the PHY @interface 707 * mode, or -EINVAL if not appropriate. 708 */ 709 static inline int phylink_get_link_timer_ns(phy_interface_t interface) 710 { 711 switch (interface) { 712 case PHY_INTERFACE_MODE_SGMII: 713 case PHY_INTERFACE_MODE_QSGMII: 714 case PHY_INTERFACE_MODE_USXGMII: 715 return 1600000; 716 717 case PHY_INTERFACE_MODE_1000BASEX: 718 case PHY_INTERFACE_MODE_2500BASEX: 719 return 10000000; 720 721 default: 722 return -EINVAL; 723 } 724 } 725 726 void phylink_mii_c22_pcs_decode_state(struct phylink_link_state *state, 727 u16 bmsr, u16 lpa); 728 void phylink_mii_c22_pcs_get_state(struct mdio_device *pcs, 729 struct phylink_link_state *state); 730 int phylink_mii_c22_pcs_encode_advertisement(phy_interface_t interface, 731 const unsigned long *advertising); 732 int phylink_mii_c22_pcs_config(struct mdio_device *pcs, 733 phy_interface_t interface, 734 const unsigned long *advertising, 735 unsigned int neg_mode); 736 void phylink_mii_c22_pcs_an_restart(struct mdio_device *pcs); 737 738 void phylink_resolve_c73(struct phylink_link_state *state); 739 740 void phylink_mii_c45_pcs_get_state(struct mdio_device *pcs, 741 struct phylink_link_state *state); 742 743 void phylink_decode_usxgmii_word(struct phylink_link_state *state, 744 uint16_t lpa); 745 #endif 746