1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright (C) 2014 Freescale Semiconductor, Inc. 4 */ 5 6 #ifndef __LINUX_MTD_SPI_NOR_H 7 #define __LINUX_MTD_SPI_NOR_H 8 9 #include <linux/bitops.h> 10 #include <linux/mtd/cfi.h> 11 #include <linux/mtd/mtd.h> 12 #include <linux/spi/spi-mem.h> 13 14 /* 15 * Note on opcode nomenclature: some opcodes have a format like 16 * SPINOR_OP_FUNCTION{4,}_x_y_z. The numbers x, y, and z stand for the number 17 * of I/O lines used for the opcode, address, and data (respectively). The 18 * FUNCTION has an optional suffix of '4', to represent an opcode which 19 * requires a 4-byte (32-bit) address. 20 */ 21 22 /* Flash opcodes. */ 23 #define SPINOR_OP_WRDI 0x04 /* Write disable */ 24 #define SPINOR_OP_WREN 0x06 /* Write enable */ 25 #define SPINOR_OP_RDSR 0x05 /* Read status register */ 26 #define SPINOR_OP_WRSR 0x01 /* Write status register 1 byte */ 27 #define SPINOR_OP_RDSR2 0x3f /* Read status register 2 */ 28 #define SPINOR_OP_WRSR2 0x3e /* Write status register 2 */ 29 #define SPINOR_OP_READ 0x03 /* Read data bytes (low frequency) */ 30 #define SPINOR_OP_READ_FAST 0x0b /* Read data bytes (high frequency) */ 31 #define SPINOR_OP_READ_1_1_2 0x3b /* Read data bytes (Dual Output SPI) */ 32 #define SPINOR_OP_READ_1_2_2 0xbb /* Read data bytes (Dual I/O SPI) */ 33 #define SPINOR_OP_READ_1_1_4 0x6b /* Read data bytes (Quad Output SPI) */ 34 #define SPINOR_OP_READ_1_4_4 0xeb /* Read data bytes (Quad I/O SPI) */ 35 #define SPINOR_OP_READ_1_1_8 0x8b /* Read data bytes (Octal Output SPI) */ 36 #define SPINOR_OP_READ_1_8_8 0xcb /* Read data bytes (Octal I/O SPI) */ 37 #define SPINOR_OP_PP 0x02 /* Page program (up to 256 bytes) */ 38 #define SPINOR_OP_PP_1_1_4 0x32 /* Quad page program */ 39 #define SPINOR_OP_PP_1_4_4 0x38 /* Quad page program */ 40 #define SPINOR_OP_PP_1_1_8 0x82 /* Octal page program */ 41 #define SPINOR_OP_PP_1_8_8 0xc2 /* Octal page program */ 42 #define SPINOR_OP_BE_4K 0x20 /* Erase 4KiB block */ 43 #define SPINOR_OP_BE_4K_PMC 0xd7 /* Erase 4KiB block on PMC chips */ 44 #define SPINOR_OP_BE_32K 0x52 /* Erase 32KiB block */ 45 #define SPINOR_OP_CHIP_ERASE 0xc7 /* Erase whole flash chip */ 46 #define SPINOR_OP_SE 0xd8 /* Sector erase (usually 64KiB) */ 47 #define SPINOR_OP_RDID 0x9f /* Read JEDEC ID */ 48 #define SPINOR_OP_RDSFDP 0x5a /* Read SFDP */ 49 #define SPINOR_OP_RDCR 0x35 /* Read configuration register */ 50 #define SPINOR_OP_RDFSR 0x70 /* Read flag status register */ 51 #define SPINOR_OP_CLFSR 0x50 /* Clear flag status register */ 52 #define SPINOR_OP_RDEAR 0xc8 /* Read Extended Address Register */ 53 #define SPINOR_OP_WREAR 0xc5 /* Write Extended Address Register */ 54 #define SPINOR_OP_SRSTEN 0x66 /* Software Reset Enable */ 55 #define SPINOR_OP_SRST 0x99 /* Software Reset */ 56 #define SPINOR_OP_GBULK 0x98 /* Global Block Unlock */ 57 58 /* 4-byte address opcodes - used on Spansion and some Macronix flashes. */ 59 #define SPINOR_OP_READ_4B 0x13 /* Read data bytes (low frequency) */ 60 #define SPINOR_OP_READ_FAST_4B 0x0c /* Read data bytes (high frequency) */ 61 #define SPINOR_OP_READ_1_1_2_4B 0x3c /* Read data bytes (Dual Output SPI) */ 62 #define SPINOR_OP_READ_1_2_2_4B 0xbc /* Read data bytes (Dual I/O SPI) */ 63 #define SPINOR_OP_READ_1_1_4_4B 0x6c /* Read data bytes (Quad Output SPI) */ 64 #define SPINOR_OP_READ_1_4_4_4B 0xec /* Read data bytes (Quad I/O SPI) */ 65 #define SPINOR_OP_READ_1_1_8_4B 0x7c /* Read data bytes (Octal Output SPI) */ 66 #define SPINOR_OP_READ_1_8_8_4B 0xcc /* Read data bytes (Octal I/O SPI) */ 67 #define SPINOR_OP_PP_4B 0x12 /* Page program (up to 256 bytes) */ 68 #define SPINOR_OP_PP_1_1_4_4B 0x34 /* Quad page program */ 69 #define SPINOR_OP_PP_1_4_4_4B 0x3e /* Quad page program */ 70 #define SPINOR_OP_PP_1_1_8_4B 0x84 /* Octal page program */ 71 #define SPINOR_OP_PP_1_8_8_4B 0x8e /* Octal page program */ 72 #define SPINOR_OP_BE_4K_4B 0x21 /* Erase 4KiB block */ 73 #define SPINOR_OP_BE_32K_4B 0x5c /* Erase 32KiB block */ 74 #define SPINOR_OP_SE_4B 0xdc /* Sector erase (usually 64KiB) */ 75 76 /* Double Transfer Rate opcodes - defined in JEDEC JESD216B. */ 77 #define SPINOR_OP_READ_1_1_1_DTR 0x0d 78 #define SPINOR_OP_READ_1_2_2_DTR 0xbd 79 #define SPINOR_OP_READ_1_4_4_DTR 0xed 80 81 #define SPINOR_OP_READ_1_1_1_DTR_4B 0x0e 82 #define SPINOR_OP_READ_1_2_2_DTR_4B 0xbe 83 #define SPINOR_OP_READ_1_4_4_DTR_4B 0xee 84 85 /* Used for SST flashes only. */ 86 #define SPINOR_OP_BP 0x02 /* Byte program */ 87 #define SPINOR_OP_AAI_WP 0xad /* Auto address increment word program */ 88 89 /* Used for S3AN flashes only */ 90 #define SPINOR_OP_XSE 0x50 /* Sector erase */ 91 #define SPINOR_OP_XPP 0x82 /* Page program */ 92 #define SPINOR_OP_XRDSR 0xd7 /* Read status register */ 93 94 #define XSR_PAGESIZE BIT(0) /* Page size in Po2 or Linear */ 95 #define XSR_RDY BIT(7) /* Ready */ 96 97 98 /* Used for Macronix and Winbond flashes. */ 99 #define SPINOR_OP_EN4B 0xb7 /* Enter 4-byte mode */ 100 #define SPINOR_OP_EX4B 0xe9 /* Exit 4-byte mode */ 101 102 /* Used for Spansion flashes only. */ 103 #define SPINOR_OP_BRWR 0x17 /* Bank register write */ 104 #define SPINOR_OP_CLSR 0x30 /* Clear status register 1 */ 105 106 /* Used for Micron flashes only. */ 107 #define SPINOR_OP_RD_EVCR 0x65 /* Read EVCR register */ 108 #define SPINOR_OP_WD_EVCR 0x61 /* Write EVCR register */ 109 110 /* Status Register bits. */ 111 #define SR_WIP BIT(0) /* Write in progress */ 112 #define SR_WEL BIT(1) /* Write enable latch */ 113 /* meaning of other SR_* bits may differ between vendors */ 114 #define SR_BP0 BIT(2) /* Block protect 0 */ 115 #define SR_BP1 BIT(3) /* Block protect 1 */ 116 #define SR_BP2 BIT(4) /* Block protect 2 */ 117 #define SR_BP3 BIT(5) /* Block protect 3 */ 118 #define SR_TB_BIT5 BIT(5) /* Top/Bottom protect */ 119 #define SR_BP3_BIT6 BIT(6) /* Block protect 3 */ 120 #define SR_TB_BIT6 BIT(6) /* Top/Bottom protect */ 121 #define SR_SRWD BIT(7) /* SR write protect */ 122 /* Spansion/Cypress specific status bits */ 123 #define SR_E_ERR BIT(5) 124 #define SR_P_ERR BIT(6) 125 126 #define SR1_QUAD_EN_BIT6 BIT(6) 127 128 #define SR_BP_SHIFT 2 129 130 /* Enhanced Volatile Configuration Register bits */ 131 #define EVCR_QUAD_EN_MICRON BIT(7) /* Micron Quad I/O */ 132 133 /* Flag Status Register bits */ 134 #define FSR_READY BIT(7) /* Device status, 0 = Busy, 1 = Ready */ 135 #define FSR_E_ERR BIT(5) /* Erase operation status */ 136 #define FSR_P_ERR BIT(4) /* Program operation status */ 137 #define FSR_PT_ERR BIT(1) /* Protection error bit */ 138 139 /* Status Register 2 bits. */ 140 #define SR2_QUAD_EN_BIT1 BIT(1) 141 #define SR2_QUAD_EN_BIT7 BIT(7) 142 143 /* Supported SPI protocols */ 144 #define SNOR_PROTO_INST_MASK GENMASK(23, 16) 145 #define SNOR_PROTO_INST_SHIFT 16 146 #define SNOR_PROTO_INST(_nbits) \ 147 ((((unsigned long)(_nbits)) << SNOR_PROTO_INST_SHIFT) & \ 148 SNOR_PROTO_INST_MASK) 149 150 #define SNOR_PROTO_ADDR_MASK GENMASK(15, 8) 151 #define SNOR_PROTO_ADDR_SHIFT 8 152 #define SNOR_PROTO_ADDR(_nbits) \ 153 ((((unsigned long)(_nbits)) << SNOR_PROTO_ADDR_SHIFT) & \ 154 SNOR_PROTO_ADDR_MASK) 155 156 #define SNOR_PROTO_DATA_MASK GENMASK(7, 0) 157 #define SNOR_PROTO_DATA_SHIFT 0 158 #define SNOR_PROTO_DATA(_nbits) \ 159 ((((unsigned long)(_nbits)) << SNOR_PROTO_DATA_SHIFT) & \ 160 SNOR_PROTO_DATA_MASK) 161 162 #define SNOR_PROTO_IS_DTR BIT(24) /* Double Transfer Rate */ 163 164 #define SNOR_PROTO_STR(_inst_nbits, _addr_nbits, _data_nbits) \ 165 (SNOR_PROTO_INST(_inst_nbits) | \ 166 SNOR_PROTO_ADDR(_addr_nbits) | \ 167 SNOR_PROTO_DATA(_data_nbits)) 168 #define SNOR_PROTO_DTR(_inst_nbits, _addr_nbits, _data_nbits) \ 169 (SNOR_PROTO_IS_DTR | \ 170 SNOR_PROTO_STR(_inst_nbits, _addr_nbits, _data_nbits)) 171 172 enum spi_nor_protocol { 173 SNOR_PROTO_1_1_1 = SNOR_PROTO_STR(1, 1, 1), 174 SNOR_PROTO_1_1_2 = SNOR_PROTO_STR(1, 1, 2), 175 SNOR_PROTO_1_1_4 = SNOR_PROTO_STR(1, 1, 4), 176 SNOR_PROTO_1_1_8 = SNOR_PROTO_STR(1, 1, 8), 177 SNOR_PROTO_1_2_2 = SNOR_PROTO_STR(1, 2, 2), 178 SNOR_PROTO_1_4_4 = SNOR_PROTO_STR(1, 4, 4), 179 SNOR_PROTO_1_8_8 = SNOR_PROTO_STR(1, 8, 8), 180 SNOR_PROTO_2_2_2 = SNOR_PROTO_STR(2, 2, 2), 181 SNOR_PROTO_4_4_4 = SNOR_PROTO_STR(4, 4, 4), 182 SNOR_PROTO_8_8_8 = SNOR_PROTO_STR(8, 8, 8), 183 184 SNOR_PROTO_1_1_1_DTR = SNOR_PROTO_DTR(1, 1, 1), 185 SNOR_PROTO_1_2_2_DTR = SNOR_PROTO_DTR(1, 2, 2), 186 SNOR_PROTO_1_4_4_DTR = SNOR_PROTO_DTR(1, 4, 4), 187 SNOR_PROTO_1_8_8_DTR = SNOR_PROTO_DTR(1, 8, 8), 188 SNOR_PROTO_8_8_8_DTR = SNOR_PROTO_DTR(8, 8, 8), 189 }; 190 191 static inline bool spi_nor_protocol_is_dtr(enum spi_nor_protocol proto) 192 { 193 return !!(proto & SNOR_PROTO_IS_DTR); 194 } 195 196 static inline u8 spi_nor_get_protocol_inst_nbits(enum spi_nor_protocol proto) 197 { 198 return ((unsigned long)(proto & SNOR_PROTO_INST_MASK)) >> 199 SNOR_PROTO_INST_SHIFT; 200 } 201 202 static inline u8 spi_nor_get_protocol_addr_nbits(enum spi_nor_protocol proto) 203 { 204 return ((unsigned long)(proto & SNOR_PROTO_ADDR_MASK)) >> 205 SNOR_PROTO_ADDR_SHIFT; 206 } 207 208 static inline u8 spi_nor_get_protocol_data_nbits(enum spi_nor_protocol proto) 209 { 210 return ((unsigned long)(proto & SNOR_PROTO_DATA_MASK)) >> 211 SNOR_PROTO_DATA_SHIFT; 212 } 213 214 static inline u8 spi_nor_get_protocol_width(enum spi_nor_protocol proto) 215 { 216 return spi_nor_get_protocol_data_nbits(proto); 217 } 218 219 /** 220 * struct spi_nor_hwcaps - Structure for describing the hardware capabilies 221 * supported by the SPI controller (bus master). 222 * @mask: the bitmask listing all the supported hw capabilies 223 */ 224 struct spi_nor_hwcaps { 225 u32 mask; 226 }; 227 228 /* 229 *(Fast) Read capabilities. 230 * MUST be ordered by priority: the higher bit position, the higher priority. 231 * As a matter of performances, it is relevant to use Octal SPI protocols first, 232 * then Quad SPI protocols before Dual SPI protocols, Fast Read and lastly 233 * (Slow) Read. 234 */ 235 #define SNOR_HWCAPS_READ_MASK GENMASK(15, 0) 236 #define SNOR_HWCAPS_READ BIT(0) 237 #define SNOR_HWCAPS_READ_FAST BIT(1) 238 #define SNOR_HWCAPS_READ_1_1_1_DTR BIT(2) 239 240 #define SNOR_HWCAPS_READ_DUAL GENMASK(6, 3) 241 #define SNOR_HWCAPS_READ_1_1_2 BIT(3) 242 #define SNOR_HWCAPS_READ_1_2_2 BIT(4) 243 #define SNOR_HWCAPS_READ_2_2_2 BIT(5) 244 #define SNOR_HWCAPS_READ_1_2_2_DTR BIT(6) 245 246 #define SNOR_HWCAPS_READ_QUAD GENMASK(10, 7) 247 #define SNOR_HWCAPS_READ_1_1_4 BIT(7) 248 #define SNOR_HWCAPS_READ_1_4_4 BIT(8) 249 #define SNOR_HWCAPS_READ_4_4_4 BIT(9) 250 #define SNOR_HWCAPS_READ_1_4_4_DTR BIT(10) 251 252 #define SNOR_HWCAPS_READ_OCTAL GENMASK(15, 11) 253 #define SNOR_HWCAPS_READ_1_1_8 BIT(11) 254 #define SNOR_HWCAPS_READ_1_8_8 BIT(12) 255 #define SNOR_HWCAPS_READ_8_8_8 BIT(13) 256 #define SNOR_HWCAPS_READ_1_8_8_DTR BIT(14) 257 #define SNOR_HWCAPS_READ_8_8_8_DTR BIT(15) 258 259 /* 260 * Page Program capabilities. 261 * MUST be ordered by priority: the higher bit position, the higher priority. 262 * Like (Fast) Read capabilities, Octal/Quad SPI protocols are preferred to the 263 * legacy SPI 1-1-1 protocol. 264 * Note that Dual Page Programs are not supported because there is no existing 265 * JEDEC/SFDP standard to define them. Also at this moment no SPI flash memory 266 * implements such commands. 267 */ 268 #define SNOR_HWCAPS_PP_MASK GENMASK(23, 16) 269 #define SNOR_HWCAPS_PP BIT(16) 270 271 #define SNOR_HWCAPS_PP_QUAD GENMASK(19, 17) 272 #define SNOR_HWCAPS_PP_1_1_4 BIT(17) 273 #define SNOR_HWCAPS_PP_1_4_4 BIT(18) 274 #define SNOR_HWCAPS_PP_4_4_4 BIT(19) 275 276 #define SNOR_HWCAPS_PP_OCTAL GENMASK(23, 20) 277 #define SNOR_HWCAPS_PP_1_1_8 BIT(20) 278 #define SNOR_HWCAPS_PP_1_8_8 BIT(21) 279 #define SNOR_HWCAPS_PP_8_8_8 BIT(22) 280 #define SNOR_HWCAPS_PP_8_8_8_DTR BIT(23) 281 282 #define SNOR_HWCAPS_X_X_X (SNOR_HWCAPS_READ_2_2_2 | \ 283 SNOR_HWCAPS_READ_4_4_4 | \ 284 SNOR_HWCAPS_READ_8_8_8 | \ 285 SNOR_HWCAPS_PP_4_4_4 | \ 286 SNOR_HWCAPS_PP_8_8_8) 287 288 #define SNOR_HWCAPS_X_X_X_DTR (SNOR_HWCAPS_READ_8_8_8_DTR | \ 289 SNOR_HWCAPS_PP_8_8_8_DTR) 290 291 #define SNOR_HWCAPS_DTR (SNOR_HWCAPS_READ_1_1_1_DTR | \ 292 SNOR_HWCAPS_READ_1_2_2_DTR | \ 293 SNOR_HWCAPS_READ_1_4_4_DTR | \ 294 SNOR_HWCAPS_READ_1_8_8_DTR | \ 295 SNOR_HWCAPS_READ_8_8_8_DTR) 296 297 #define SNOR_HWCAPS_ALL (SNOR_HWCAPS_READ_MASK | \ 298 SNOR_HWCAPS_PP_MASK) 299 300 /* Forward declaration that is used in 'struct spi_nor_controller_ops' */ 301 struct spi_nor; 302 303 /** 304 * struct spi_nor_controller_ops - SPI NOR controller driver specific 305 * operations. 306 * @prepare: [OPTIONAL] do some preparations for the 307 * read/write/erase/lock/unlock operations. 308 * @unprepare: [OPTIONAL] do some post work after the 309 * read/write/erase/lock/unlock operations. 310 * @read_reg: read out the register. 311 * @write_reg: write data to the register. 312 * @read: read data from the SPI NOR. 313 * @write: write data to the SPI NOR. 314 * @erase: erase a sector of the SPI NOR at the offset @offs; if 315 * not provided by the driver, SPI NOR will send the erase 316 * opcode via write_reg(). 317 */ 318 struct spi_nor_controller_ops { 319 int (*prepare)(struct spi_nor *nor); 320 void (*unprepare)(struct spi_nor *nor); 321 int (*read_reg)(struct spi_nor *nor, u8 opcode, u8 *buf, size_t len); 322 int (*write_reg)(struct spi_nor *nor, u8 opcode, const u8 *buf, 323 size_t len); 324 325 ssize_t (*read)(struct spi_nor *nor, loff_t from, size_t len, u8 *buf); 326 ssize_t (*write)(struct spi_nor *nor, loff_t to, size_t len, 327 const u8 *buf); 328 int (*erase)(struct spi_nor *nor, loff_t offs); 329 }; 330 331 /** 332 * enum spi_nor_cmd_ext - describes the command opcode extension in DTR mode 333 * @SPI_NOR_EXT_NONE: no extension. This is the default, and is used in Legacy 334 * SPI mode 335 * @SPI_NOR_EXT_REPEAT: the extension is same as the opcode 336 * @SPI_NOR_EXT_INVERT: the extension is the bitwise inverse of the opcode 337 * @SPI_NOR_EXT_HEX: the extension is any hex value. The command and opcode 338 * combine to form a 16-bit opcode. 339 */ 340 enum spi_nor_cmd_ext { 341 SPI_NOR_EXT_NONE = 0, 342 SPI_NOR_EXT_REPEAT, 343 SPI_NOR_EXT_INVERT, 344 SPI_NOR_EXT_HEX, 345 }; 346 347 /* 348 * Forward declarations that are used internally by the core and manufacturer 349 * drivers. 350 */ 351 struct flash_info; 352 struct spi_nor_manufacturer; 353 struct spi_nor_flash_parameter; 354 355 /** 356 * struct spi_nor - Structure for defining the SPI NOR layer 357 * @mtd: an mtd_info structure 358 * @lock: the lock for the read/write/erase/lock/unlock operations 359 * @dev: pointer to an SPI device or an SPI NOR controller device 360 * @spimem: pointer to the SPI memory device 361 * @bouncebuf: bounce buffer used when the buffer passed by the MTD 362 * layer is not DMA-able 363 * @bouncebuf_size: size of the bounce buffer 364 * @info: SPI NOR part JEDEC MFR ID and other info 365 * @manufacturer: SPI NOR manufacturer 366 * @page_size: the page size of the SPI NOR 367 * @addr_width: number of address bytes 368 * @erase_opcode: the opcode for erasing a sector 369 * @read_opcode: the read opcode 370 * @read_dummy: the dummy needed by the read operation 371 * @program_opcode: the program opcode 372 * @sst_write_second: used by the SST write operation 373 * @flags: flag options for the current SPI NOR (SNOR_F_*) 374 * @cmd_ext_type: the command opcode extension type for DTR mode. 375 * @read_proto: the SPI protocol for read operations 376 * @write_proto: the SPI protocol for write operations 377 * @reg_proto: the SPI protocol for read_reg/write_reg/erase operations 378 * @controller_ops: SPI NOR controller driver specific operations. 379 * @params: [FLASH-SPECIFIC] SPI NOR flash parameters and settings. 380 * The structure includes legacy flash parameters and 381 * settings that can be overwritten by the spi_nor_fixups 382 * hooks, or dynamically when parsing the SFDP tables. 383 * @dirmap: pointers to struct spi_mem_dirmap_desc for reads/writes. 384 * @priv: pointer to the private data 385 */ 386 struct spi_nor { 387 struct mtd_info mtd; 388 struct mutex lock; 389 struct device *dev; 390 struct spi_mem *spimem; 391 u8 *bouncebuf; 392 size_t bouncebuf_size; 393 const struct flash_info *info; 394 const struct spi_nor_manufacturer *manufacturer; 395 u32 page_size; 396 u8 addr_width; 397 u8 erase_opcode; 398 u8 read_opcode; 399 u8 read_dummy; 400 u8 program_opcode; 401 enum spi_nor_protocol read_proto; 402 enum spi_nor_protocol write_proto; 403 enum spi_nor_protocol reg_proto; 404 bool sst_write_second; 405 u32 flags; 406 enum spi_nor_cmd_ext cmd_ext_type; 407 408 const struct spi_nor_controller_ops *controller_ops; 409 410 struct spi_nor_flash_parameter *params; 411 412 struct { 413 struct spi_mem_dirmap_desc *rdesc; 414 struct spi_mem_dirmap_desc *wdesc; 415 } dirmap; 416 417 void *priv; 418 }; 419 420 static inline void spi_nor_set_flash_node(struct spi_nor *nor, 421 struct device_node *np) 422 { 423 mtd_set_of_node(&nor->mtd, np); 424 } 425 426 static inline struct device_node *spi_nor_get_flash_node(struct spi_nor *nor) 427 { 428 return mtd_get_of_node(&nor->mtd); 429 } 430 431 /** 432 * spi_nor_scan() - scan the SPI NOR 433 * @nor: the spi_nor structure 434 * @name: the chip type name 435 * @hwcaps: the hardware capabilities supported by the controller driver 436 * 437 * The drivers can use this function to scan the SPI NOR. 438 * In the scanning, it will try to get all the necessary information to 439 * fill the mtd_info{} and the spi_nor{}. 440 * 441 * The chip type name can be provided through the @name parameter. 442 * 443 * Return: 0 for success, others for failure. 444 */ 445 int spi_nor_scan(struct spi_nor *nor, const char *name, 446 const struct spi_nor_hwcaps *hwcaps); 447 448 /** 449 * spi_nor_restore_addr_mode() - restore the status of SPI NOR 450 * @nor: the spi_nor structure 451 */ 452 void spi_nor_restore(struct spi_nor *nor); 453 454 #endif 455