1 /* 2 * linux/include/linux/mtd/nand.h 3 * 4 * Copyright © 2000-2010 David Woodhouse <[email protected]> 5 * Steven J. Hill <[email protected]> 6 * Thomas Gleixner <[email protected]> 7 * 8 * This program is free software; you can redistribute it and/or modify 9 * it under the terms of the GNU General Public License version 2 as 10 * published by the Free Software Foundation. 11 * 12 * Info: 13 * Contains standard defines and IDs for NAND flash devices 14 * 15 * Changelog: 16 * See git changelog. 17 */ 18 #ifndef __LINUX_MTD_NAND_H 19 #define __LINUX_MTD_NAND_H 20 21 #include <linux/wait.h> 22 #include <linux/spinlock.h> 23 #include <linux/mtd/mtd.h> 24 #include <linux/mtd/flashchip.h> 25 #include <linux/mtd/bbm.h> 26 27 struct mtd_info; 28 struct nand_flash_dev; 29 struct device_node; 30 31 /* Scan and identify a NAND device */ 32 extern int nand_scan(struct mtd_info *mtd, int max_chips); 33 /* 34 * Separate phases of nand_scan(), allowing board driver to intervene 35 * and override command or ECC setup according to flash type. 36 */ 37 extern int nand_scan_ident(struct mtd_info *mtd, int max_chips, 38 struct nand_flash_dev *table); 39 extern int nand_scan_tail(struct mtd_info *mtd); 40 41 /* Free resources held by the NAND device */ 42 extern void nand_release(struct mtd_info *mtd); 43 44 /* Internal helper for board drivers which need to override command function */ 45 extern void nand_wait_ready(struct mtd_info *mtd); 46 47 /* locks all blocks present in the device */ 48 extern int nand_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len); 49 50 /* unlocks specified locked blocks */ 51 extern int nand_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len); 52 53 /* The maximum number of NAND chips in an array */ 54 #define NAND_MAX_CHIPS 8 55 56 /* 57 * Constants for hardware specific CLE/ALE/NCE function 58 * 59 * These are bits which can be or'ed to set/clear multiple 60 * bits in one go. 61 */ 62 /* Select the chip by setting nCE to low */ 63 #define NAND_NCE 0x01 64 /* Select the command latch by setting CLE to high */ 65 #define NAND_CLE 0x02 66 /* Select the address latch by setting ALE to high */ 67 #define NAND_ALE 0x04 68 69 #define NAND_CTRL_CLE (NAND_NCE | NAND_CLE) 70 #define NAND_CTRL_ALE (NAND_NCE | NAND_ALE) 71 #define NAND_CTRL_CHANGE 0x80 72 73 /* 74 * Standard NAND flash commands 75 */ 76 #define NAND_CMD_READ0 0 77 #define NAND_CMD_READ1 1 78 #define NAND_CMD_RNDOUT 5 79 #define NAND_CMD_PAGEPROG 0x10 80 #define NAND_CMD_READOOB 0x50 81 #define NAND_CMD_ERASE1 0x60 82 #define NAND_CMD_STATUS 0x70 83 #define NAND_CMD_SEQIN 0x80 84 #define NAND_CMD_RNDIN 0x85 85 #define NAND_CMD_READID 0x90 86 #define NAND_CMD_ERASE2 0xd0 87 #define NAND_CMD_PARAM 0xec 88 #define NAND_CMD_GET_FEATURES 0xee 89 #define NAND_CMD_SET_FEATURES 0xef 90 #define NAND_CMD_RESET 0xff 91 92 #define NAND_CMD_LOCK 0x2a 93 #define NAND_CMD_UNLOCK1 0x23 94 #define NAND_CMD_UNLOCK2 0x24 95 96 /* Extended commands for large page devices */ 97 #define NAND_CMD_READSTART 0x30 98 #define NAND_CMD_RNDOUTSTART 0xE0 99 #define NAND_CMD_CACHEDPROG 0x15 100 101 #define NAND_CMD_NONE -1 102 103 /* Status bits */ 104 #define NAND_STATUS_FAIL 0x01 105 #define NAND_STATUS_FAIL_N1 0x02 106 #define NAND_STATUS_TRUE_READY 0x20 107 #define NAND_STATUS_READY 0x40 108 #define NAND_STATUS_WP 0x80 109 110 /* 111 * Constants for ECC_MODES 112 */ 113 typedef enum { 114 NAND_ECC_NONE, 115 NAND_ECC_SOFT, 116 NAND_ECC_HW, 117 NAND_ECC_HW_SYNDROME, 118 NAND_ECC_HW_OOB_FIRST, 119 NAND_ECC_SOFT_BCH, 120 } nand_ecc_modes_t; 121 122 /* 123 * Constants for Hardware ECC 124 */ 125 /* Reset Hardware ECC for read */ 126 #define NAND_ECC_READ 0 127 /* Reset Hardware ECC for write */ 128 #define NAND_ECC_WRITE 1 129 /* Enable Hardware ECC before syndrome is read back from flash */ 130 #define NAND_ECC_READSYN 2 131 132 /* Bit mask for flags passed to do_nand_read_ecc */ 133 #define NAND_GET_DEVICE 0x80 134 135 136 /* 137 * Option constants for bizarre disfunctionality and real 138 * features. 139 */ 140 /* Buswidth is 16 bit */ 141 #define NAND_BUSWIDTH_16 0x00000002 142 /* Chip has cache program function */ 143 #define NAND_CACHEPRG 0x00000008 144 /* 145 * Chip requires ready check on read (for auto-incremented sequential read). 146 * True only for small page devices; large page devices do not support 147 * autoincrement. 148 */ 149 #define NAND_NEED_READRDY 0x00000100 150 151 /* Chip does not allow subpage writes */ 152 #define NAND_NO_SUBPAGE_WRITE 0x00000200 153 154 /* Device is one of 'new' xD cards that expose fake nand command set */ 155 #define NAND_BROKEN_XD 0x00000400 156 157 /* Device behaves just like nand, but is readonly */ 158 #define NAND_ROM 0x00000800 159 160 /* Device supports subpage reads */ 161 #define NAND_SUBPAGE_READ 0x00001000 162 163 /* Options valid for Samsung large page devices */ 164 #define NAND_SAMSUNG_LP_OPTIONS NAND_CACHEPRG 165 166 /* Macros to identify the above */ 167 #define NAND_HAS_CACHEPROG(chip) ((chip->options & NAND_CACHEPRG)) 168 #define NAND_HAS_SUBPAGE_READ(chip) ((chip->options & NAND_SUBPAGE_READ)) 169 170 /* Non chip related options */ 171 /* This option skips the bbt scan during initialization. */ 172 #define NAND_SKIP_BBTSCAN 0x00010000 173 /* 174 * This option is defined if the board driver allocates its own buffers 175 * (e.g. because it needs them DMA-coherent). 176 */ 177 #define NAND_OWN_BUFFERS 0x00020000 178 /* Chip may not exist, so silence any errors in scan */ 179 #define NAND_SCAN_SILENT_NODEV 0x00040000 180 /* 181 * Autodetect nand buswidth with readid/onfi. 182 * This suppose the driver will configure the hardware in 8 bits mode 183 * when calling nand_scan_ident, and update its configuration 184 * before calling nand_scan_tail. 185 */ 186 #define NAND_BUSWIDTH_AUTO 0x00080000 187 /* 188 * This option could be defined by controller drivers to protect against 189 * kmap'ed, vmalloc'ed highmem buffers being passed from upper layers 190 */ 191 #define NAND_USE_BOUNCE_BUFFER 0x00100000 192 193 /* Options set by nand scan */ 194 /* Nand scan has allocated controller struct */ 195 #define NAND_CONTROLLER_ALLOC 0x80000000 196 197 /* Cell info constants */ 198 #define NAND_CI_CHIPNR_MSK 0x03 199 #define NAND_CI_CELLTYPE_MSK 0x0C 200 #define NAND_CI_CELLTYPE_SHIFT 2 201 202 /* Keep gcc happy */ 203 struct nand_chip; 204 205 /* ONFI features */ 206 #define ONFI_FEATURE_16_BIT_BUS (1 << 0) 207 #define ONFI_FEATURE_EXT_PARAM_PAGE (1 << 7) 208 209 /* ONFI timing mode, used in both asynchronous and synchronous mode */ 210 #define ONFI_TIMING_MODE_0 (1 << 0) 211 #define ONFI_TIMING_MODE_1 (1 << 1) 212 #define ONFI_TIMING_MODE_2 (1 << 2) 213 #define ONFI_TIMING_MODE_3 (1 << 3) 214 #define ONFI_TIMING_MODE_4 (1 << 4) 215 #define ONFI_TIMING_MODE_5 (1 << 5) 216 #define ONFI_TIMING_MODE_UNKNOWN (1 << 6) 217 218 /* ONFI feature address */ 219 #define ONFI_FEATURE_ADDR_TIMING_MODE 0x1 220 221 /* Vendor-specific feature address (Micron) */ 222 #define ONFI_FEATURE_ADDR_READ_RETRY 0x89 223 224 /* ONFI subfeature parameters length */ 225 #define ONFI_SUBFEATURE_PARAM_LEN 4 226 227 /* ONFI optional commands SET/GET FEATURES supported? */ 228 #define ONFI_OPT_CMD_SET_GET_FEATURES (1 << 2) 229 230 struct nand_onfi_params { 231 /* rev info and features block */ 232 /* 'O' 'N' 'F' 'I' */ 233 u8 sig[4]; 234 __le16 revision; 235 __le16 features; 236 __le16 opt_cmd; 237 u8 reserved0[2]; 238 __le16 ext_param_page_length; /* since ONFI 2.1 */ 239 u8 num_of_param_pages; /* since ONFI 2.1 */ 240 u8 reserved1[17]; 241 242 /* manufacturer information block */ 243 char manufacturer[12]; 244 char model[20]; 245 u8 jedec_id; 246 __le16 date_code; 247 u8 reserved2[13]; 248 249 /* memory organization block */ 250 __le32 byte_per_page; 251 __le16 spare_bytes_per_page; 252 __le32 data_bytes_per_ppage; 253 __le16 spare_bytes_per_ppage; 254 __le32 pages_per_block; 255 __le32 blocks_per_lun; 256 u8 lun_count; 257 u8 addr_cycles; 258 u8 bits_per_cell; 259 __le16 bb_per_lun; 260 __le16 block_endurance; 261 u8 guaranteed_good_blocks; 262 __le16 guaranteed_block_endurance; 263 u8 programs_per_page; 264 u8 ppage_attr; 265 u8 ecc_bits; 266 u8 interleaved_bits; 267 u8 interleaved_ops; 268 u8 reserved3[13]; 269 270 /* electrical parameter block */ 271 u8 io_pin_capacitance_max; 272 __le16 async_timing_mode; 273 __le16 program_cache_timing_mode; 274 __le16 t_prog; 275 __le16 t_bers; 276 __le16 t_r; 277 __le16 t_ccs; 278 __le16 src_sync_timing_mode; 279 __le16 src_ssync_features; 280 __le16 clk_pin_capacitance_typ; 281 __le16 io_pin_capacitance_typ; 282 __le16 input_pin_capacitance_typ; 283 u8 input_pin_capacitance_max; 284 u8 driver_strength_support; 285 __le16 t_int_r; 286 __le16 t_ald; 287 u8 reserved4[7]; 288 289 /* vendor */ 290 __le16 vendor_revision; 291 u8 vendor[88]; 292 293 __le16 crc; 294 } __packed; 295 296 #define ONFI_CRC_BASE 0x4F4E 297 298 /* Extended ECC information Block Definition (since ONFI 2.1) */ 299 struct onfi_ext_ecc_info { 300 u8 ecc_bits; 301 u8 codeword_size; 302 __le16 bb_per_lun; 303 __le16 block_endurance; 304 u8 reserved[2]; 305 } __packed; 306 307 #define ONFI_SECTION_TYPE_0 0 /* Unused section. */ 308 #define ONFI_SECTION_TYPE_1 1 /* for additional sections. */ 309 #define ONFI_SECTION_TYPE_2 2 /* for ECC information. */ 310 struct onfi_ext_section { 311 u8 type; 312 u8 length; 313 } __packed; 314 315 #define ONFI_EXT_SECTION_MAX 8 316 317 /* Extended Parameter Page Definition (since ONFI 2.1) */ 318 struct onfi_ext_param_page { 319 __le16 crc; 320 u8 sig[4]; /* 'E' 'P' 'P' 'S' */ 321 u8 reserved0[10]; 322 struct onfi_ext_section sections[ONFI_EXT_SECTION_MAX]; 323 324 /* 325 * The actual size of the Extended Parameter Page is in 326 * @ext_param_page_length of nand_onfi_params{}. 327 * The following are the variable length sections. 328 * So we do not add any fields below. Please see the ONFI spec. 329 */ 330 } __packed; 331 332 struct nand_onfi_vendor_micron { 333 u8 two_plane_read; 334 u8 read_cache; 335 u8 read_unique_id; 336 u8 dq_imped; 337 u8 dq_imped_num_settings; 338 u8 dq_imped_feat_addr; 339 u8 rb_pulldown_strength; 340 u8 rb_pulldown_strength_feat_addr; 341 u8 rb_pulldown_strength_num_settings; 342 u8 otp_mode; 343 u8 otp_page_start; 344 u8 otp_data_prot_addr; 345 u8 otp_num_pages; 346 u8 otp_feat_addr; 347 u8 read_retry_options; 348 u8 reserved[72]; 349 u8 param_revision; 350 } __packed; 351 352 struct jedec_ecc_info { 353 u8 ecc_bits; 354 u8 codeword_size; 355 __le16 bb_per_lun; 356 __le16 block_endurance; 357 u8 reserved[2]; 358 } __packed; 359 360 /* JEDEC features */ 361 #define JEDEC_FEATURE_16_BIT_BUS (1 << 0) 362 363 struct nand_jedec_params { 364 /* rev info and features block */ 365 /* 'J' 'E' 'S' 'D' */ 366 u8 sig[4]; 367 __le16 revision; 368 __le16 features; 369 u8 opt_cmd[3]; 370 __le16 sec_cmd; 371 u8 num_of_param_pages; 372 u8 reserved0[18]; 373 374 /* manufacturer information block */ 375 char manufacturer[12]; 376 char model[20]; 377 u8 jedec_id[6]; 378 u8 reserved1[10]; 379 380 /* memory organization block */ 381 __le32 byte_per_page; 382 __le16 spare_bytes_per_page; 383 u8 reserved2[6]; 384 __le32 pages_per_block; 385 __le32 blocks_per_lun; 386 u8 lun_count; 387 u8 addr_cycles; 388 u8 bits_per_cell; 389 u8 programs_per_page; 390 u8 multi_plane_addr; 391 u8 multi_plane_op_attr; 392 u8 reserved3[38]; 393 394 /* electrical parameter block */ 395 __le16 async_sdr_speed_grade; 396 __le16 toggle_ddr_speed_grade; 397 __le16 sync_ddr_speed_grade; 398 u8 async_sdr_features; 399 u8 toggle_ddr_features; 400 u8 sync_ddr_features; 401 __le16 t_prog; 402 __le16 t_bers; 403 __le16 t_r; 404 __le16 t_r_multi_plane; 405 __le16 t_ccs; 406 __le16 io_pin_capacitance_typ; 407 __le16 input_pin_capacitance_typ; 408 __le16 clk_pin_capacitance_typ; 409 u8 driver_strength_support; 410 __le16 t_ald; 411 u8 reserved4[36]; 412 413 /* ECC and endurance block */ 414 u8 guaranteed_good_blocks; 415 __le16 guaranteed_block_endurance; 416 struct jedec_ecc_info ecc_info[4]; 417 u8 reserved5[29]; 418 419 /* reserved */ 420 u8 reserved6[148]; 421 422 /* vendor */ 423 __le16 vendor_rev_num; 424 u8 reserved7[88]; 425 426 /* CRC for Parameter Page */ 427 __le16 crc; 428 } __packed; 429 430 /** 431 * struct nand_hw_control - Control structure for hardware controller (e.g ECC generator) shared among independent devices 432 * @lock: protection lock 433 * @active: the mtd device which holds the controller currently 434 * @wq: wait queue to sleep on if a NAND operation is in 435 * progress used instead of the per chip wait queue 436 * when a hw controller is available. 437 */ 438 struct nand_hw_control { 439 spinlock_t lock; 440 struct nand_chip *active; 441 wait_queue_head_t wq; 442 }; 443 444 /** 445 * struct nand_ecc_ctrl - Control structure for ECC 446 * @mode: ECC mode 447 * @steps: number of ECC steps per page 448 * @size: data bytes per ECC step 449 * @bytes: ECC bytes per step 450 * @strength: max number of correctible bits per ECC step 451 * @total: total number of ECC bytes per page 452 * @prepad: padding information for syndrome based ECC generators 453 * @postpad: padding information for syndrome based ECC generators 454 * @layout: ECC layout control struct pointer 455 * @priv: pointer to private ECC control data 456 * @hwctl: function to control hardware ECC generator. Must only 457 * be provided if an hardware ECC is available 458 * @calculate: function for ECC calculation or readback from ECC hardware 459 * @correct: function for ECC correction, matching to ECC generator (sw/hw) 460 * @read_page_raw: function to read a raw page without ECC. This function 461 * should hide the specific layout used by the ECC 462 * controller and always return contiguous in-band and 463 * out-of-band data even if they're not stored 464 * contiguously on the NAND chip (e.g. 465 * NAND_ECC_HW_SYNDROME interleaves in-band and 466 * out-of-band data). 467 * @write_page_raw: function to write a raw page without ECC. This function 468 * should hide the specific layout used by the ECC 469 * controller and consider the passed data as contiguous 470 * in-band and out-of-band data. ECC controller is 471 * responsible for doing the appropriate transformations 472 * to adapt to its specific layout (e.g. 473 * NAND_ECC_HW_SYNDROME interleaves in-band and 474 * out-of-band data). 475 * @read_page: function to read a page according to the ECC generator 476 * requirements; returns maximum number of bitflips corrected in 477 * any single ECC step, 0 if bitflips uncorrectable, -EIO hw error 478 * @read_subpage: function to read parts of the page covered by ECC; 479 * returns same as read_page() 480 * @write_subpage: function to write parts of the page covered by ECC. 481 * @write_page: function to write a page according to the ECC generator 482 * requirements. 483 * @write_oob_raw: function to write chip OOB data without ECC 484 * @read_oob_raw: function to read chip OOB data without ECC 485 * @read_oob: function to read chip OOB data 486 * @write_oob: function to write chip OOB data 487 */ 488 struct nand_ecc_ctrl { 489 nand_ecc_modes_t mode; 490 int steps; 491 int size; 492 int bytes; 493 int total; 494 int strength; 495 int prepad; 496 int postpad; 497 struct nand_ecclayout *layout; 498 void *priv; 499 void (*hwctl)(struct mtd_info *mtd, int mode); 500 int (*calculate)(struct mtd_info *mtd, const uint8_t *dat, 501 uint8_t *ecc_code); 502 int (*correct)(struct mtd_info *mtd, uint8_t *dat, uint8_t *read_ecc, 503 uint8_t *calc_ecc); 504 int (*read_page_raw)(struct mtd_info *mtd, struct nand_chip *chip, 505 uint8_t *buf, int oob_required, int page); 506 int (*write_page_raw)(struct mtd_info *mtd, struct nand_chip *chip, 507 const uint8_t *buf, int oob_required); 508 int (*read_page)(struct mtd_info *mtd, struct nand_chip *chip, 509 uint8_t *buf, int oob_required, int page); 510 int (*read_subpage)(struct mtd_info *mtd, struct nand_chip *chip, 511 uint32_t offs, uint32_t len, uint8_t *buf, int page); 512 int (*write_subpage)(struct mtd_info *mtd, struct nand_chip *chip, 513 uint32_t offset, uint32_t data_len, 514 const uint8_t *data_buf, int oob_required); 515 int (*write_page)(struct mtd_info *mtd, struct nand_chip *chip, 516 const uint8_t *buf, int oob_required); 517 int (*write_oob_raw)(struct mtd_info *mtd, struct nand_chip *chip, 518 int page); 519 int (*read_oob_raw)(struct mtd_info *mtd, struct nand_chip *chip, 520 int page); 521 int (*read_oob)(struct mtd_info *mtd, struct nand_chip *chip, int page); 522 int (*write_oob)(struct mtd_info *mtd, struct nand_chip *chip, 523 int page); 524 }; 525 526 /** 527 * struct nand_buffers - buffer structure for read/write 528 * @ecccalc: buffer pointer for calculated ECC, size is oobsize. 529 * @ecccode: buffer pointer for ECC read from flash, size is oobsize. 530 * @databuf: buffer pointer for data, size is (page size + oobsize). 531 * 532 * Do not change the order of buffers. databuf and oobrbuf must be in 533 * consecutive order. 534 */ 535 struct nand_buffers { 536 uint8_t *ecccalc; 537 uint8_t *ecccode; 538 uint8_t *databuf; 539 }; 540 541 /** 542 * struct nand_chip - NAND Private Flash Chip Data 543 * @IO_ADDR_R: [BOARDSPECIFIC] address to read the 8 I/O lines of the 544 * flash device 545 * @IO_ADDR_W: [BOARDSPECIFIC] address to write the 8 I/O lines of the 546 * flash device. 547 * @dn: [BOARDSPECIFIC] device node describing this instance 548 * @read_byte: [REPLACEABLE] read one byte from the chip 549 * @read_word: [REPLACEABLE] read one word from the chip 550 * @write_byte: [REPLACEABLE] write a single byte to the chip on the 551 * low 8 I/O lines 552 * @write_buf: [REPLACEABLE] write data from the buffer to the chip 553 * @read_buf: [REPLACEABLE] read data from the chip into the buffer 554 * @select_chip: [REPLACEABLE] select chip nr 555 * @block_bad: [REPLACEABLE] check if a block is bad, using OOB markers 556 * @block_markbad: [REPLACEABLE] mark a block bad 557 * @cmd_ctrl: [BOARDSPECIFIC] hardwarespecific function for controlling 558 * ALE/CLE/nCE. Also used to write command and address 559 * @init_size: [BOARDSPECIFIC] hardwarespecific function for setting 560 * mtd->oobsize, mtd->writesize and so on. 561 * @id_data contains the 8 bytes values of NAND_CMD_READID. 562 * Return with the bus width. 563 * @dev_ready: [BOARDSPECIFIC] hardwarespecific function for accessing 564 * device ready/busy line. If set to NULL no access to 565 * ready/busy is available and the ready/busy information 566 * is read from the chip status register. 567 * @cmdfunc: [REPLACEABLE] hardwarespecific function for writing 568 * commands to the chip. 569 * @waitfunc: [REPLACEABLE] hardwarespecific function for wait on 570 * ready. 571 * @setup_read_retry: [FLASHSPECIFIC] flash (vendor) specific function for 572 * setting the read-retry mode. Mostly needed for MLC NAND. 573 * @ecc: [BOARDSPECIFIC] ECC control structure 574 * @buffers: buffer structure for read/write 575 * @hwcontrol: platform-specific hardware control structure 576 * @erase: [REPLACEABLE] erase function 577 * @scan_bbt: [REPLACEABLE] function to scan bad block table 578 * @chip_delay: [BOARDSPECIFIC] chip dependent delay for transferring 579 * data from array to read regs (tR). 580 * @state: [INTERN] the current state of the NAND device 581 * @oob_poi: "poison value buffer," used for laying out OOB data 582 * before writing 583 * @page_shift: [INTERN] number of address bits in a page (column 584 * address bits). 585 * @phys_erase_shift: [INTERN] number of address bits in a physical eraseblock 586 * @bbt_erase_shift: [INTERN] number of address bits in a bbt entry 587 * @chip_shift: [INTERN] number of address bits in one chip 588 * @options: [BOARDSPECIFIC] various chip options. They can partly 589 * be set to inform nand_scan about special functionality. 590 * See the defines for further explanation. 591 * @bbt_options: [INTERN] bad block specific options. All options used 592 * here must come from bbm.h. By default, these options 593 * will be copied to the appropriate nand_bbt_descr's. 594 * @badblockpos: [INTERN] position of the bad block marker in the oob 595 * area. 596 * @badblockbits: [INTERN] minimum number of set bits in a good block's 597 * bad block marker position; i.e., BBM == 11110111b is 598 * not bad when badblockbits == 7 599 * @bits_per_cell: [INTERN] number of bits per cell. i.e., 1 means SLC. 600 * @ecc_strength_ds: [INTERN] ECC correctability from the datasheet. 601 * Minimum amount of bit errors per @ecc_step_ds guaranteed 602 * to be correctable. If unknown, set to zero. 603 * @ecc_step_ds: [INTERN] ECC step required by the @ecc_strength_ds, 604 * also from the datasheet. It is the recommended ECC step 605 * size, if known; if unknown, set to zero. 606 * @onfi_timing_mode_default: [INTERN] default ONFI timing mode. This field is 607 * either deduced from the datasheet if the NAND 608 * chip is not ONFI compliant or set to 0 if it is 609 * (an ONFI chip is always configured in mode 0 610 * after a NAND reset) 611 * @numchips: [INTERN] number of physical chips 612 * @chipsize: [INTERN] the size of one chip for multichip arrays 613 * @pagemask: [INTERN] page number mask = number of (pages / chip) - 1 614 * @pagebuf: [INTERN] holds the pagenumber which is currently in 615 * data_buf. 616 * @pagebuf_bitflips: [INTERN] holds the bitflip count for the page which is 617 * currently in data_buf. 618 * @subpagesize: [INTERN] holds the subpagesize 619 * @onfi_version: [INTERN] holds the chip ONFI version (BCD encoded), 620 * non 0 if ONFI supported. 621 * @jedec_version: [INTERN] holds the chip JEDEC version (BCD encoded), 622 * non 0 if JEDEC supported. 623 * @onfi_params: [INTERN] holds the ONFI page parameter when ONFI is 624 * supported, 0 otherwise. 625 * @jedec_params: [INTERN] holds the JEDEC parameter page when JEDEC is 626 * supported, 0 otherwise. 627 * @read_retries: [INTERN] the number of read retry modes supported 628 * @onfi_set_features: [REPLACEABLE] set the features for ONFI nand 629 * @onfi_get_features: [REPLACEABLE] get the features for ONFI nand 630 * @bbt: [INTERN] bad block table pointer 631 * @bbt_td: [REPLACEABLE] bad block table descriptor for flash 632 * lookup. 633 * @bbt_md: [REPLACEABLE] bad block table mirror descriptor 634 * @badblock_pattern: [REPLACEABLE] bad block scan pattern used for initial 635 * bad block scan. 636 * @controller: [REPLACEABLE] a pointer to a hardware controller 637 * structure which is shared among multiple independent 638 * devices. 639 * @priv: [OPTIONAL] pointer to private chip data 640 * @errstat: [OPTIONAL] hardware specific function to perform 641 * additional error status checks (determine if errors are 642 * correctable). 643 * @write_page: [REPLACEABLE] High-level page write function 644 */ 645 646 struct nand_chip { 647 void __iomem *IO_ADDR_R; 648 void __iomem *IO_ADDR_W; 649 650 struct device_node *dn; 651 652 uint8_t (*read_byte)(struct mtd_info *mtd); 653 u16 (*read_word)(struct mtd_info *mtd); 654 void (*write_byte)(struct mtd_info *mtd, uint8_t byte); 655 void (*write_buf)(struct mtd_info *mtd, const uint8_t *buf, int len); 656 void (*read_buf)(struct mtd_info *mtd, uint8_t *buf, int len); 657 void (*select_chip)(struct mtd_info *mtd, int chip); 658 int (*block_bad)(struct mtd_info *mtd, loff_t ofs, int getchip); 659 int (*block_markbad)(struct mtd_info *mtd, loff_t ofs); 660 void (*cmd_ctrl)(struct mtd_info *mtd, int dat, unsigned int ctrl); 661 int (*init_size)(struct mtd_info *mtd, struct nand_chip *this, 662 u8 *id_data); 663 int (*dev_ready)(struct mtd_info *mtd); 664 void (*cmdfunc)(struct mtd_info *mtd, unsigned command, int column, 665 int page_addr); 666 int(*waitfunc)(struct mtd_info *mtd, struct nand_chip *this); 667 int (*erase)(struct mtd_info *mtd, int page); 668 int (*scan_bbt)(struct mtd_info *mtd); 669 int (*errstat)(struct mtd_info *mtd, struct nand_chip *this, int state, 670 int status, int page); 671 int (*write_page)(struct mtd_info *mtd, struct nand_chip *chip, 672 uint32_t offset, int data_len, const uint8_t *buf, 673 int oob_required, int page, int cached, int raw); 674 int (*onfi_set_features)(struct mtd_info *mtd, struct nand_chip *chip, 675 int feature_addr, uint8_t *subfeature_para); 676 int (*onfi_get_features)(struct mtd_info *mtd, struct nand_chip *chip, 677 int feature_addr, uint8_t *subfeature_para); 678 int (*setup_read_retry)(struct mtd_info *mtd, int retry_mode); 679 680 int chip_delay; 681 unsigned int options; 682 unsigned int bbt_options; 683 684 int page_shift; 685 int phys_erase_shift; 686 int bbt_erase_shift; 687 int chip_shift; 688 int numchips; 689 uint64_t chipsize; 690 int pagemask; 691 int pagebuf; 692 unsigned int pagebuf_bitflips; 693 int subpagesize; 694 uint8_t bits_per_cell; 695 uint16_t ecc_strength_ds; 696 uint16_t ecc_step_ds; 697 int onfi_timing_mode_default; 698 int badblockpos; 699 int badblockbits; 700 701 int onfi_version; 702 int jedec_version; 703 union { 704 struct nand_onfi_params onfi_params; 705 struct nand_jedec_params jedec_params; 706 }; 707 708 int read_retries; 709 710 flstate_t state; 711 712 uint8_t *oob_poi; 713 struct nand_hw_control *controller; 714 715 struct nand_ecc_ctrl ecc; 716 struct nand_buffers *buffers; 717 struct nand_hw_control hwcontrol; 718 719 uint8_t *bbt; 720 struct nand_bbt_descr *bbt_td; 721 struct nand_bbt_descr *bbt_md; 722 723 struct nand_bbt_descr *badblock_pattern; 724 725 void *priv; 726 }; 727 728 /* 729 * NAND Flash Manufacturer ID Codes 730 */ 731 #define NAND_MFR_TOSHIBA 0x98 732 #define NAND_MFR_SAMSUNG 0xec 733 #define NAND_MFR_FUJITSU 0x04 734 #define NAND_MFR_NATIONAL 0x8f 735 #define NAND_MFR_RENESAS 0x07 736 #define NAND_MFR_STMICRO 0x20 737 #define NAND_MFR_HYNIX 0xad 738 #define NAND_MFR_MICRON 0x2c 739 #define NAND_MFR_AMD 0x01 740 #define NAND_MFR_MACRONIX 0xc2 741 #define NAND_MFR_EON 0x92 742 #define NAND_MFR_SANDISK 0x45 743 #define NAND_MFR_INTEL 0x89 744 #define NAND_MFR_ATO 0x9b 745 746 /* The maximum expected count of bytes in the NAND ID sequence */ 747 #define NAND_MAX_ID_LEN 8 748 749 /* 750 * A helper for defining older NAND chips where the second ID byte fully 751 * defined the chip, including the geometry (chip size, eraseblock size, page 752 * size). All these chips have 512 bytes NAND page size. 753 */ 754 #define LEGACY_ID_NAND(nm, devid, chipsz, erasesz, opts) \ 755 { .name = (nm), {{ .dev_id = (devid) }}, .pagesize = 512, \ 756 .chipsize = (chipsz), .erasesize = (erasesz), .options = (opts) } 757 758 /* 759 * A helper for defining newer chips which report their page size and 760 * eraseblock size via the extended ID bytes. 761 * 762 * The real difference between LEGACY_ID_NAND and EXTENDED_ID_NAND is that with 763 * EXTENDED_ID_NAND, manufacturers overloaded the same device ID so that the 764 * device ID now only represented a particular total chip size (and voltage, 765 * buswidth), and the page size, eraseblock size, and OOB size could vary while 766 * using the same device ID. 767 */ 768 #define EXTENDED_ID_NAND(nm, devid, chipsz, opts) \ 769 { .name = (nm), {{ .dev_id = (devid) }}, .chipsize = (chipsz), \ 770 .options = (opts) } 771 772 #define NAND_ECC_INFO(_strength, _step) \ 773 { .strength_ds = (_strength), .step_ds = (_step) } 774 #define NAND_ECC_STRENGTH(type) ((type)->ecc.strength_ds) 775 #define NAND_ECC_STEP(type) ((type)->ecc.step_ds) 776 777 /** 778 * struct nand_flash_dev - NAND Flash Device ID Structure 779 * @name: a human-readable name of the NAND chip 780 * @dev_id: the device ID (the second byte of the full chip ID array) 781 * @mfr_id: manufecturer ID part of the full chip ID array (refers the same 782 * memory address as @id[0]) 783 * @dev_id: device ID part of the full chip ID array (refers the same memory 784 * address as @id[1]) 785 * @id: full device ID array 786 * @pagesize: size of the NAND page in bytes; if 0, then the real page size (as 787 * well as the eraseblock size) is determined from the extended NAND 788 * chip ID array) 789 * @chipsize: total chip size in MiB 790 * @erasesize: eraseblock size in bytes (determined from the extended ID if 0) 791 * @options: stores various chip bit options 792 * @id_len: The valid length of the @id. 793 * @oobsize: OOB size 794 * @ecc: ECC correctability and step information from the datasheet. 795 * @ecc.strength_ds: The ECC correctability from the datasheet, same as the 796 * @ecc_strength_ds in nand_chip{}. 797 * @ecc.step_ds: The ECC step required by the @ecc.strength_ds, same as the 798 * @ecc_step_ds in nand_chip{}, also from the datasheet. 799 * For example, the "4bit ECC for each 512Byte" can be set with 800 * NAND_ECC_INFO(4, 512). 801 * @onfi_timing_mode_default: the default ONFI timing mode entered after a NAND 802 * reset. Should be deduced from timings described 803 * in the datasheet. 804 * 805 */ 806 struct nand_flash_dev { 807 char *name; 808 union { 809 struct { 810 uint8_t mfr_id; 811 uint8_t dev_id; 812 }; 813 uint8_t id[NAND_MAX_ID_LEN]; 814 }; 815 unsigned int pagesize; 816 unsigned int chipsize; 817 unsigned int erasesize; 818 unsigned int options; 819 uint16_t id_len; 820 uint16_t oobsize; 821 struct { 822 uint16_t strength_ds; 823 uint16_t step_ds; 824 } ecc; 825 int onfi_timing_mode_default; 826 }; 827 828 /** 829 * struct nand_manufacturers - NAND Flash Manufacturer ID Structure 830 * @name: Manufacturer name 831 * @id: manufacturer ID code of device. 832 */ 833 struct nand_manufacturers { 834 int id; 835 char *name; 836 }; 837 838 extern struct nand_flash_dev nand_flash_ids[]; 839 extern struct nand_manufacturers nand_manuf_ids[]; 840 841 extern int nand_default_bbt(struct mtd_info *mtd); 842 extern int nand_markbad_bbt(struct mtd_info *mtd, loff_t offs); 843 extern int nand_isreserved_bbt(struct mtd_info *mtd, loff_t offs); 844 extern int nand_isbad_bbt(struct mtd_info *mtd, loff_t offs, int allowbbt); 845 extern int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr, 846 int allowbbt); 847 extern int nand_do_read(struct mtd_info *mtd, loff_t from, size_t len, 848 size_t *retlen, uint8_t *buf); 849 850 /** 851 * struct platform_nand_chip - chip level device structure 852 * @nr_chips: max. number of chips to scan for 853 * @chip_offset: chip number offset 854 * @nr_partitions: number of partitions pointed to by partitions (or zero) 855 * @partitions: mtd partition list 856 * @chip_delay: R/B delay value in us 857 * @options: Option flags, e.g. 16bit buswidth 858 * @bbt_options: BBT option flags, e.g. NAND_BBT_USE_FLASH 859 * @ecclayout: ECC layout info structure 860 * @part_probe_types: NULL-terminated array of probe types 861 */ 862 struct platform_nand_chip { 863 int nr_chips; 864 int chip_offset; 865 int nr_partitions; 866 struct mtd_partition *partitions; 867 struct nand_ecclayout *ecclayout; 868 int chip_delay; 869 unsigned int options; 870 unsigned int bbt_options; 871 const char **part_probe_types; 872 }; 873 874 /* Keep gcc happy */ 875 struct platform_device; 876 877 /** 878 * struct platform_nand_ctrl - controller level device structure 879 * @probe: platform specific function to probe/setup hardware 880 * @remove: platform specific function to remove/teardown hardware 881 * @hwcontrol: platform specific hardware control structure 882 * @dev_ready: platform specific function to read ready/busy pin 883 * @select_chip: platform specific chip select function 884 * @cmd_ctrl: platform specific function for controlling 885 * ALE/CLE/nCE. Also used to write command and address 886 * @write_buf: platform specific function for write buffer 887 * @read_buf: platform specific function for read buffer 888 * @read_byte: platform specific function to read one byte from chip 889 * @priv: private data to transport driver specific settings 890 * 891 * All fields are optional and depend on the hardware driver requirements 892 */ 893 struct platform_nand_ctrl { 894 int (*probe)(struct platform_device *pdev); 895 void (*remove)(struct platform_device *pdev); 896 void (*hwcontrol)(struct mtd_info *mtd, int cmd); 897 int (*dev_ready)(struct mtd_info *mtd); 898 void (*select_chip)(struct mtd_info *mtd, int chip); 899 void (*cmd_ctrl)(struct mtd_info *mtd, int dat, unsigned int ctrl); 900 void (*write_buf)(struct mtd_info *mtd, const uint8_t *buf, int len); 901 void (*read_buf)(struct mtd_info *mtd, uint8_t *buf, int len); 902 unsigned char (*read_byte)(struct mtd_info *mtd); 903 void *priv; 904 }; 905 906 /** 907 * struct platform_nand_data - container structure for platform-specific data 908 * @chip: chip level chip structure 909 * @ctrl: controller level device structure 910 */ 911 struct platform_nand_data { 912 struct platform_nand_chip chip; 913 struct platform_nand_ctrl ctrl; 914 }; 915 916 /* Some helpers to access the data structures */ 917 static inline 918 struct platform_nand_chip *get_platform_nandchip(struct mtd_info *mtd) 919 { 920 struct nand_chip *chip = mtd->priv; 921 922 return chip->priv; 923 } 924 925 /* return the supported features. */ 926 static inline int onfi_feature(struct nand_chip *chip) 927 { 928 return chip->onfi_version ? le16_to_cpu(chip->onfi_params.features) : 0; 929 } 930 931 /* return the supported asynchronous timing mode. */ 932 static inline int onfi_get_async_timing_mode(struct nand_chip *chip) 933 { 934 if (!chip->onfi_version) 935 return ONFI_TIMING_MODE_UNKNOWN; 936 return le16_to_cpu(chip->onfi_params.async_timing_mode); 937 } 938 939 /* return the supported synchronous timing mode. */ 940 static inline int onfi_get_sync_timing_mode(struct nand_chip *chip) 941 { 942 if (!chip->onfi_version) 943 return ONFI_TIMING_MODE_UNKNOWN; 944 return le16_to_cpu(chip->onfi_params.src_sync_timing_mode); 945 } 946 947 /* 948 * Check if it is a SLC nand. 949 * The !nand_is_slc() can be used to check the MLC/TLC nand chips. 950 * We do not distinguish the MLC and TLC now. 951 */ 952 static inline bool nand_is_slc(struct nand_chip *chip) 953 { 954 return chip->bits_per_cell == 1; 955 } 956 957 /** 958 * Check if the opcode's address should be sent only on the lower 8 bits 959 * @command: opcode to check 960 */ 961 static inline int nand_opcode_8bits(unsigned int command) 962 { 963 switch (command) { 964 case NAND_CMD_READID: 965 case NAND_CMD_PARAM: 966 case NAND_CMD_GET_FEATURES: 967 case NAND_CMD_SET_FEATURES: 968 return 1; 969 default: 970 break; 971 } 972 return 0; 973 } 974 975 /* return the supported JEDEC features. */ 976 static inline int jedec_feature(struct nand_chip *chip) 977 { 978 return chip->jedec_version ? le16_to_cpu(chip->jedec_params.features) 979 : 0; 980 } 981 982 /* 983 * struct nand_sdr_timings - SDR NAND chip timings 984 * 985 * This struct defines the timing requirements of a SDR NAND chip. 986 * These informations can be found in every NAND datasheets and the timings 987 * meaning are described in the ONFI specifications: 988 * www.onfi.org/~/media/ONFI/specs/onfi_3_1_spec.pdf (chapter 4.15 Timing 989 * Parameters) 990 * 991 * All these timings are expressed in picoseconds. 992 */ 993 994 struct nand_sdr_timings { 995 u32 tALH_min; 996 u32 tADL_min; 997 u32 tALS_min; 998 u32 tAR_min; 999 u32 tCEA_max; 1000 u32 tCEH_min; 1001 u32 tCH_min; 1002 u32 tCHZ_max; 1003 u32 tCLH_min; 1004 u32 tCLR_min; 1005 u32 tCLS_min; 1006 u32 tCOH_min; 1007 u32 tCS_min; 1008 u32 tDH_min; 1009 u32 tDS_min; 1010 u32 tFEAT_max; 1011 u32 tIR_min; 1012 u32 tITC_max; 1013 u32 tRC_min; 1014 u32 tREA_max; 1015 u32 tREH_min; 1016 u32 tRHOH_min; 1017 u32 tRHW_min; 1018 u32 tRHZ_max; 1019 u32 tRLOH_min; 1020 u32 tRP_min; 1021 u32 tRR_min; 1022 u64 tRST_max; 1023 u32 tWB_max; 1024 u32 tWC_min; 1025 u32 tWH_min; 1026 u32 tWHR_min; 1027 u32 tWP_min; 1028 u32 tWW_min; 1029 }; 1030 1031 /* get timing characteristics from ONFI timing mode. */ 1032 const struct nand_sdr_timings *onfi_async_timing_mode_to_sdr_timings(int mode); 1033 #endif /* __LINUX_MTD_NAND_H */ 1034