1 /* 2 * linux/include/linux/mtd/nand.h 3 * 4 * Copyright (c) 2000 David Woodhouse <[email protected]> 5 * Steven J. Hill <[email protected]> 6 * Thomas Gleixner <[email protected]> 7 * 8 * This program is free software; you can redistribute it and/or modify 9 * it under the terms of the GNU General Public License version 2 as 10 * published by the Free Software Foundation. 11 * 12 * Info: 13 * Contains standard defines and IDs for NAND flash devices 14 * 15 * Changelog: 16 * See git changelog. 17 */ 18 #ifndef __LINUX_MTD_NAND_H 19 #define __LINUX_MTD_NAND_H 20 21 #include <linux/wait.h> 22 #include <linux/spinlock.h> 23 #include <linux/mtd/mtd.h> 24 25 struct mtd_info; 26 /* Scan and identify a NAND device */ 27 extern int nand_scan (struct mtd_info *mtd, int max_chips); 28 /* Separate phases of nand_scan(), allowing board driver to intervene 29 * and override command or ECC setup according to flash type */ 30 extern int nand_scan_ident(struct mtd_info *mtd, int max_chips); 31 extern int nand_scan_tail(struct mtd_info *mtd); 32 33 /* Free resources held by the NAND device */ 34 extern void nand_release (struct mtd_info *mtd); 35 36 /* Internal helper for board drivers which need to override command function */ 37 extern void nand_wait_ready(struct mtd_info *mtd); 38 39 /* The maximum number of NAND chips in an array */ 40 #define NAND_MAX_CHIPS 8 41 42 /* This constant declares the max. oobsize / page, which 43 * is supported now. If you add a chip with bigger oobsize/page 44 * adjust this accordingly. 45 */ 46 #define NAND_MAX_OOBSIZE 64 47 #define NAND_MAX_PAGESIZE 2048 48 49 /* 50 * Constants for hardware specific CLE/ALE/NCE function 51 * 52 * These are bits which can be or'ed to set/clear multiple 53 * bits in one go. 54 */ 55 /* Select the chip by setting nCE to low */ 56 #define NAND_NCE 0x01 57 /* Select the command latch by setting CLE to high */ 58 #define NAND_CLE 0x02 59 /* Select the address latch by setting ALE to high */ 60 #define NAND_ALE 0x04 61 62 #define NAND_CTRL_CLE (NAND_NCE | NAND_CLE) 63 #define NAND_CTRL_ALE (NAND_NCE | NAND_ALE) 64 #define NAND_CTRL_CHANGE 0x80 65 66 /* 67 * Standard NAND flash commands 68 */ 69 #define NAND_CMD_READ0 0 70 #define NAND_CMD_READ1 1 71 #define NAND_CMD_RNDOUT 5 72 #define NAND_CMD_PAGEPROG 0x10 73 #define NAND_CMD_READOOB 0x50 74 #define NAND_CMD_ERASE1 0x60 75 #define NAND_CMD_STATUS 0x70 76 #define NAND_CMD_STATUS_MULTI 0x71 77 #define NAND_CMD_SEQIN 0x80 78 #define NAND_CMD_RNDIN 0x85 79 #define NAND_CMD_READID 0x90 80 #define NAND_CMD_ERASE2 0xd0 81 #define NAND_CMD_RESET 0xff 82 83 /* Extended commands for large page devices */ 84 #define NAND_CMD_READSTART 0x30 85 #define NAND_CMD_RNDOUTSTART 0xE0 86 #define NAND_CMD_CACHEDPROG 0x15 87 88 /* Extended commands for AG-AND device */ 89 /* 90 * Note: the command for NAND_CMD_DEPLETE1 is really 0x00 but 91 * there is no way to distinguish that from NAND_CMD_READ0 92 * until the remaining sequence of commands has been completed 93 * so add a high order bit and mask it off in the command. 94 */ 95 #define NAND_CMD_DEPLETE1 0x100 96 #define NAND_CMD_DEPLETE2 0x38 97 #define NAND_CMD_STATUS_MULTI 0x71 98 #define NAND_CMD_STATUS_ERROR 0x72 99 /* multi-bank error status (banks 0-3) */ 100 #define NAND_CMD_STATUS_ERROR0 0x73 101 #define NAND_CMD_STATUS_ERROR1 0x74 102 #define NAND_CMD_STATUS_ERROR2 0x75 103 #define NAND_CMD_STATUS_ERROR3 0x76 104 #define NAND_CMD_STATUS_RESET 0x7f 105 #define NAND_CMD_STATUS_CLEAR 0xff 106 107 #define NAND_CMD_NONE -1 108 109 /* Status bits */ 110 #define NAND_STATUS_FAIL 0x01 111 #define NAND_STATUS_FAIL_N1 0x02 112 #define NAND_STATUS_TRUE_READY 0x20 113 #define NAND_STATUS_READY 0x40 114 #define NAND_STATUS_WP 0x80 115 116 /* 117 * Constants for ECC_MODES 118 */ 119 typedef enum { 120 NAND_ECC_NONE, 121 NAND_ECC_SOFT, 122 NAND_ECC_HW, 123 NAND_ECC_HW_SYNDROME, 124 } nand_ecc_modes_t; 125 126 /* 127 * Constants for Hardware ECC 128 */ 129 /* Reset Hardware ECC for read */ 130 #define NAND_ECC_READ 0 131 /* Reset Hardware ECC for write */ 132 #define NAND_ECC_WRITE 1 133 /* Enable Hardware ECC before syndrom is read back from flash */ 134 #define NAND_ECC_READSYN 2 135 136 /* Bit mask for flags passed to do_nand_read_ecc */ 137 #define NAND_GET_DEVICE 0x80 138 139 140 /* Option constants for bizarre disfunctionality and real 141 * features 142 */ 143 /* Chip can not auto increment pages */ 144 #define NAND_NO_AUTOINCR 0x00000001 145 /* Buswitdh is 16 bit */ 146 #define NAND_BUSWIDTH_16 0x00000002 147 /* Device supports partial programming without padding */ 148 #define NAND_NO_PADDING 0x00000004 149 /* Chip has cache program function */ 150 #define NAND_CACHEPRG 0x00000008 151 /* Chip has copy back function */ 152 #define NAND_COPYBACK 0x00000010 153 /* AND Chip which has 4 banks and a confusing page / block 154 * assignment. See Renesas datasheet for further information */ 155 #define NAND_IS_AND 0x00000020 156 /* Chip has a array of 4 pages which can be read without 157 * additional ready /busy waits */ 158 #define NAND_4PAGE_ARRAY 0x00000040 159 /* Chip requires that BBT is periodically rewritten to prevent 160 * bits from adjacent blocks from 'leaking' in altering data. 161 * This happens with the Renesas AG-AND chips, possibly others. */ 162 #define BBT_AUTO_REFRESH 0x00000080 163 /* Chip does not require ready check on read. True 164 * for all large page devices, as they do not support 165 * autoincrement.*/ 166 #define NAND_NO_READRDY 0x00000100 167 /* Chip does not allow subpage writes */ 168 #define NAND_NO_SUBPAGE_WRITE 0x00000200 169 170 171 /* Options valid for Samsung large page devices */ 172 #define NAND_SAMSUNG_LP_OPTIONS \ 173 (NAND_NO_PADDING | NAND_CACHEPRG | NAND_COPYBACK) 174 175 /* Macros to identify the above */ 176 #define NAND_CANAUTOINCR(chip) (!(chip->options & NAND_NO_AUTOINCR)) 177 #define NAND_MUST_PAD(chip) (!(chip->options & NAND_NO_PADDING)) 178 #define NAND_HAS_CACHEPROG(chip) ((chip->options & NAND_CACHEPRG)) 179 #define NAND_HAS_COPYBACK(chip) ((chip->options & NAND_COPYBACK)) 180 /* Large page NAND with SOFT_ECC should support subpage reads */ 181 #define NAND_SUBPAGE_READ(chip) ((chip->ecc.mode == NAND_ECC_SOFT) \ 182 && (chip->page_shift > 9)) 183 184 /* Mask to zero out the chip options, which come from the id table */ 185 #define NAND_CHIPOPTIONS_MSK (0x0000ffff & ~NAND_NO_AUTOINCR) 186 187 /* Non chip related options */ 188 /* Use a flash based bad block table. This option is passed to the 189 * default bad block table function. */ 190 #define NAND_USE_FLASH_BBT 0x00010000 191 /* This option skips the bbt scan during initialization. */ 192 #define NAND_SKIP_BBTSCAN 0x00020000 193 /* This option is defined if the board driver allocates its own buffers 194 (e.g. because it needs them DMA-coherent */ 195 #define NAND_OWN_BUFFERS 0x00040000 196 /* Options set by nand scan */ 197 /* Nand scan has allocated controller struct */ 198 #define NAND_CONTROLLER_ALLOC 0x80000000 199 200 /* Cell info constants */ 201 #define NAND_CI_CHIPNR_MSK 0x03 202 #define NAND_CI_CELLTYPE_MSK 0x0C 203 204 /* 205 * nand_state_t - chip states 206 * Enumeration for NAND flash chip state 207 */ 208 typedef enum { 209 FL_READY, 210 FL_READING, 211 FL_WRITING, 212 FL_ERASING, 213 FL_SYNCING, 214 FL_CACHEDPRG, 215 FL_PM_SUSPENDED, 216 } nand_state_t; 217 218 /* Keep gcc happy */ 219 struct nand_chip; 220 221 /** 222 * struct nand_hw_control - Control structure for hardware controller (e.g ECC generator) shared among independent devices 223 * @lock: protection lock 224 * @active: the mtd device which holds the controller currently 225 * @wq: wait queue to sleep on if a NAND operation is in progress 226 * used instead of the per chip wait queue when a hw controller is available 227 */ 228 struct nand_hw_control { 229 spinlock_t lock; 230 struct nand_chip *active; 231 wait_queue_head_t wq; 232 }; 233 234 /** 235 * struct nand_ecc_ctrl - Control structure for ecc 236 * @mode: ecc mode 237 * @steps: number of ecc steps per page 238 * @size: data bytes per ecc step 239 * @bytes: ecc bytes per step 240 * @total: total number of ecc bytes per page 241 * @prepad: padding information for syndrome based ecc generators 242 * @postpad: padding information for syndrome based ecc generators 243 * @layout: ECC layout control struct pointer 244 * @hwctl: function to control hardware ecc generator. Must only 245 * be provided if an hardware ECC is available 246 * @calculate: function for ecc calculation or readback from ecc hardware 247 * @correct: function for ecc correction, matching to ecc generator (sw/hw) 248 * @read_page_raw: function to read a raw page without ECC 249 * @write_page_raw: function to write a raw page without ECC 250 * @read_page: function to read a page according to the ecc generator requirements 251 * @read_subpage: function to read parts of the page covered by ECC. 252 * @write_page: function to write a page according to the ecc generator requirements 253 * @read_oob: function to read chip OOB data 254 * @write_oob: function to write chip OOB data 255 */ 256 struct nand_ecc_ctrl { 257 nand_ecc_modes_t mode; 258 int steps; 259 int size; 260 int bytes; 261 int total; 262 int prepad; 263 int postpad; 264 struct nand_ecclayout *layout; 265 void (*hwctl)(struct mtd_info *mtd, int mode); 266 int (*calculate)(struct mtd_info *mtd, 267 const uint8_t *dat, 268 uint8_t *ecc_code); 269 int (*correct)(struct mtd_info *mtd, uint8_t *dat, 270 uint8_t *read_ecc, 271 uint8_t *calc_ecc); 272 int (*read_page_raw)(struct mtd_info *mtd, 273 struct nand_chip *chip, 274 uint8_t *buf); 275 void (*write_page_raw)(struct mtd_info *mtd, 276 struct nand_chip *chip, 277 const uint8_t *buf); 278 int (*read_page)(struct mtd_info *mtd, 279 struct nand_chip *chip, 280 uint8_t *buf); 281 int (*read_subpage)(struct mtd_info *mtd, 282 struct nand_chip *chip, 283 uint32_t offs, uint32_t len, 284 uint8_t *buf); 285 void (*write_page)(struct mtd_info *mtd, 286 struct nand_chip *chip, 287 const uint8_t *buf); 288 int (*read_oob)(struct mtd_info *mtd, 289 struct nand_chip *chip, 290 int page, 291 int sndcmd); 292 int (*write_oob)(struct mtd_info *mtd, 293 struct nand_chip *chip, 294 int page); 295 }; 296 297 /** 298 * struct nand_buffers - buffer structure for read/write 299 * @ecccalc: buffer for calculated ecc 300 * @ecccode: buffer for ecc read from flash 301 * @databuf: buffer for data - dynamically sized 302 * 303 * Do not change the order of buffers. databuf and oobrbuf must be in 304 * consecutive order. 305 */ 306 struct nand_buffers { 307 uint8_t ecccalc[NAND_MAX_OOBSIZE]; 308 uint8_t ecccode[NAND_MAX_OOBSIZE]; 309 uint8_t databuf[NAND_MAX_PAGESIZE + NAND_MAX_OOBSIZE]; 310 }; 311 312 /** 313 * struct nand_chip - NAND Private Flash Chip Data 314 * @IO_ADDR_R: [BOARDSPECIFIC] address to read the 8 I/O lines of the flash device 315 * @IO_ADDR_W: [BOARDSPECIFIC] address to write the 8 I/O lines of the flash device 316 * @read_byte: [REPLACEABLE] read one byte from the chip 317 * @read_word: [REPLACEABLE] read one word from the chip 318 * @write_buf: [REPLACEABLE] write data from the buffer to the chip 319 * @read_buf: [REPLACEABLE] read data from the chip into the buffer 320 * @verify_buf: [REPLACEABLE] verify buffer contents against the chip data 321 * @select_chip: [REPLACEABLE] select chip nr 322 * @block_bad: [REPLACEABLE] check, if the block is bad 323 * @block_markbad: [REPLACEABLE] mark the block bad 324 * @cmd_ctrl: [BOARDSPECIFIC] hardwarespecific funtion for controlling 325 * ALE/CLE/nCE. Also used to write command and address 326 * @dev_ready: [BOARDSPECIFIC] hardwarespecific function for accesing device ready/busy line 327 * If set to NULL no access to ready/busy is available and the ready/busy information 328 * is read from the chip status register 329 * @cmdfunc: [REPLACEABLE] hardwarespecific function for writing commands to the chip 330 * @waitfunc: [REPLACEABLE] hardwarespecific function for wait on ready 331 * @ecc: [BOARDSPECIFIC] ecc control ctructure 332 * @buffers: buffer structure for read/write 333 * @hwcontrol: platform-specific hardware control structure 334 * @ops: oob operation operands 335 * @erase_cmd: [INTERN] erase command write function, selectable due to AND support 336 * @scan_bbt: [REPLACEABLE] function to scan bad block table 337 * @chip_delay: [BOARDSPECIFIC] chip dependent delay for transfering data from array to read regs (tR) 338 * @state: [INTERN] the current state of the NAND device 339 * @oob_poi: poison value buffer 340 * @page_shift: [INTERN] number of address bits in a page (column address bits) 341 * @phys_erase_shift: [INTERN] number of address bits in a physical eraseblock 342 * @bbt_erase_shift: [INTERN] number of address bits in a bbt entry 343 * @chip_shift: [INTERN] number of address bits in one chip 344 * @options: [BOARDSPECIFIC] various chip options. They can partly be set to inform nand_scan about 345 * special functionality. See the defines for further explanation 346 * @badblockpos: [INTERN] position of the bad block marker in the oob area 347 * @cellinfo: [INTERN] MLC/multichip data from chip ident 348 * @numchips: [INTERN] number of physical chips 349 * @chipsize: [INTERN] the size of one chip for multichip arrays 350 * @pagemask: [INTERN] page number mask = number of (pages / chip) - 1 351 * @pagebuf: [INTERN] holds the pagenumber which is currently in data_buf 352 * @subpagesize: [INTERN] holds the subpagesize 353 * @ecclayout: [REPLACEABLE] the default ecc placement scheme 354 * @bbt: [INTERN] bad block table pointer 355 * @bbt_td: [REPLACEABLE] bad block table descriptor for flash lookup 356 * @bbt_md: [REPLACEABLE] bad block table mirror descriptor 357 * @badblock_pattern: [REPLACEABLE] bad block scan pattern used for initial bad block scan 358 * @controller: [REPLACEABLE] a pointer to a hardware controller structure 359 * which is shared among multiple independend devices 360 * @priv: [OPTIONAL] pointer to private chip date 361 * @errstat: [OPTIONAL] hardware specific function to perform additional error status checks 362 * (determine if errors are correctable) 363 * @write_page: [REPLACEABLE] High-level page write function 364 */ 365 366 struct nand_chip { 367 void __iomem *IO_ADDR_R; 368 void __iomem *IO_ADDR_W; 369 370 uint8_t (*read_byte)(struct mtd_info *mtd); 371 u16 (*read_word)(struct mtd_info *mtd); 372 void (*write_buf)(struct mtd_info *mtd, const uint8_t *buf, int len); 373 void (*read_buf)(struct mtd_info *mtd, uint8_t *buf, int len); 374 int (*verify_buf)(struct mtd_info *mtd, const uint8_t *buf, int len); 375 void (*select_chip)(struct mtd_info *mtd, int chip); 376 int (*block_bad)(struct mtd_info *mtd, loff_t ofs, int getchip); 377 int (*block_markbad)(struct mtd_info *mtd, loff_t ofs); 378 void (*cmd_ctrl)(struct mtd_info *mtd, int dat, 379 unsigned int ctrl); 380 int (*dev_ready)(struct mtd_info *mtd); 381 void (*cmdfunc)(struct mtd_info *mtd, unsigned command, int column, int page_addr); 382 int (*waitfunc)(struct mtd_info *mtd, struct nand_chip *this); 383 void (*erase_cmd)(struct mtd_info *mtd, int page); 384 int (*scan_bbt)(struct mtd_info *mtd); 385 int (*errstat)(struct mtd_info *mtd, struct nand_chip *this, int state, int status, int page); 386 int (*write_page)(struct mtd_info *mtd, struct nand_chip *chip, 387 const uint8_t *buf, int page, int cached, int raw); 388 389 int chip_delay; 390 unsigned int options; 391 392 int page_shift; 393 int phys_erase_shift; 394 int bbt_erase_shift; 395 int chip_shift; 396 int numchips; 397 uint64_t chipsize; 398 int pagemask; 399 int pagebuf; 400 int subpagesize; 401 uint8_t cellinfo; 402 int badblockpos; 403 404 nand_state_t state; 405 406 uint8_t *oob_poi; 407 struct nand_hw_control *controller; 408 struct nand_ecclayout *ecclayout; 409 410 struct nand_ecc_ctrl ecc; 411 struct nand_buffers *buffers; 412 struct nand_hw_control hwcontrol; 413 414 struct mtd_oob_ops ops; 415 416 uint8_t *bbt; 417 struct nand_bbt_descr *bbt_td; 418 struct nand_bbt_descr *bbt_md; 419 420 struct nand_bbt_descr *badblock_pattern; 421 422 void *priv; 423 }; 424 425 /* 426 * NAND Flash Manufacturer ID Codes 427 */ 428 #define NAND_MFR_TOSHIBA 0x98 429 #define NAND_MFR_SAMSUNG 0xec 430 #define NAND_MFR_FUJITSU 0x04 431 #define NAND_MFR_NATIONAL 0x8f 432 #define NAND_MFR_RENESAS 0x07 433 #define NAND_MFR_STMICRO 0x20 434 #define NAND_MFR_HYNIX 0xad 435 #define NAND_MFR_MICRON 0x2c 436 #define NAND_MFR_AMD 0x01 437 438 /** 439 * struct nand_flash_dev - NAND Flash Device ID Structure 440 * @name: Identify the device type 441 * @id: device ID code 442 * @pagesize: Pagesize in bytes. Either 256 or 512 or 0 443 * If the pagesize is 0, then the real pagesize 444 * and the eraseize are determined from the 445 * extended id bytes in the chip 446 * @erasesize: Size of an erase block in the flash device. 447 * @chipsize: Total chipsize in Mega Bytes 448 * @options: Bitfield to store chip relevant options 449 */ 450 struct nand_flash_dev { 451 char *name; 452 int id; 453 unsigned long pagesize; 454 unsigned long chipsize; 455 unsigned long erasesize; 456 unsigned long options; 457 }; 458 459 /** 460 * struct nand_manufacturers - NAND Flash Manufacturer ID Structure 461 * @name: Manufacturer name 462 * @id: manufacturer ID code of device. 463 */ 464 struct nand_manufacturers { 465 int id; 466 char * name; 467 }; 468 469 extern struct nand_flash_dev nand_flash_ids[]; 470 extern struct nand_manufacturers nand_manuf_ids[]; 471 472 /** 473 * struct nand_bbt_descr - bad block table descriptor 474 * @options: options for this descriptor 475 * @pages: the page(s) where we find the bbt, used with option BBT_ABSPAGE 476 * when bbt is searched, then we store the found bbts pages here. 477 * Its an array and supports up to 8 chips now 478 * @offs: offset of the pattern in the oob area of the page 479 * @veroffs: offset of the bbt version counter in the oob are of the page 480 * @version: version read from the bbt page during scan 481 * @len: length of the pattern, if 0 no pattern check is performed 482 * @maxblocks: maximum number of blocks to search for a bbt. This number of 483 * blocks is reserved at the end of the device where the tables are 484 * written. 485 * @reserved_block_code: if non-0, this pattern denotes a reserved (rather than 486 * bad) block in the stored bbt 487 * @pattern: pattern to identify bad block table or factory marked good / 488 * bad blocks, can be NULL, if len = 0 489 * 490 * Descriptor for the bad block table marker and the descriptor for the 491 * pattern which identifies good and bad blocks. The assumption is made 492 * that the pattern and the version count are always located in the oob area 493 * of the first block. 494 */ 495 struct nand_bbt_descr { 496 int options; 497 int pages[NAND_MAX_CHIPS]; 498 int offs; 499 int veroffs; 500 uint8_t version[NAND_MAX_CHIPS]; 501 int len; 502 int maxblocks; 503 int reserved_block_code; 504 uint8_t *pattern; 505 }; 506 507 /* Options for the bad block table descriptors */ 508 509 /* The number of bits used per block in the bbt on the device */ 510 #define NAND_BBT_NRBITS_MSK 0x0000000F 511 #define NAND_BBT_1BIT 0x00000001 512 #define NAND_BBT_2BIT 0x00000002 513 #define NAND_BBT_4BIT 0x00000004 514 #define NAND_BBT_8BIT 0x00000008 515 /* The bad block table is in the last good block of the device */ 516 #define NAND_BBT_LASTBLOCK 0x00000010 517 /* The bbt is at the given page, else we must scan for the bbt */ 518 #define NAND_BBT_ABSPAGE 0x00000020 519 /* The bbt is at the given page, else we must scan for the bbt */ 520 #define NAND_BBT_SEARCH 0x00000040 521 /* bbt is stored per chip on multichip devices */ 522 #define NAND_BBT_PERCHIP 0x00000080 523 /* bbt has a version counter at offset veroffs */ 524 #define NAND_BBT_VERSION 0x00000100 525 /* Create a bbt if none axists */ 526 #define NAND_BBT_CREATE 0x00000200 527 /* Search good / bad pattern through all pages of a block */ 528 #define NAND_BBT_SCANALLPAGES 0x00000400 529 /* Scan block empty during good / bad block scan */ 530 #define NAND_BBT_SCANEMPTY 0x00000800 531 /* Write bbt if neccecary */ 532 #define NAND_BBT_WRITE 0x00001000 533 /* Read and write back block contents when writing bbt */ 534 #define NAND_BBT_SAVECONTENT 0x00002000 535 /* Search good / bad pattern on the first and the second page */ 536 #define NAND_BBT_SCAN2NDPAGE 0x00004000 537 538 /* The maximum number of blocks to scan for a bbt */ 539 #define NAND_BBT_SCAN_MAXBLOCKS 4 540 541 extern int nand_scan_bbt(struct mtd_info *mtd, struct nand_bbt_descr *bd); 542 extern int nand_update_bbt(struct mtd_info *mtd, loff_t offs); 543 extern int nand_default_bbt(struct mtd_info *mtd); 544 extern int nand_isbad_bbt(struct mtd_info *mtd, loff_t offs, int allowbbt); 545 extern int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr, 546 int allowbbt); 547 extern int nand_do_read(struct mtd_info *mtd, loff_t from, size_t len, 548 size_t * retlen, uint8_t * buf); 549 550 /* 551 * Constants for oob configuration 552 */ 553 #define NAND_SMALL_BADBLOCK_POS 5 554 #define NAND_LARGE_BADBLOCK_POS 0 555 556 /** 557 * struct platform_nand_chip - chip level device structure 558 * @nr_chips: max. number of chips to scan for 559 * @chip_offset: chip number offset 560 * @nr_partitions: number of partitions pointed to by partitions (or zero) 561 * @partitions: mtd partition list 562 * @chip_delay: R/B delay value in us 563 * @options: Option flags, e.g. 16bit buswidth 564 * @ecclayout: ecc layout info structure 565 * @part_probe_types: NULL-terminated array of probe types 566 * @priv: hardware controller specific settings 567 */ 568 struct platform_nand_chip { 569 int nr_chips; 570 int chip_offset; 571 int nr_partitions; 572 struct mtd_partition *partitions; 573 struct nand_ecclayout *ecclayout; 574 int chip_delay; 575 unsigned int options; 576 const char **part_probe_types; 577 void *priv; 578 }; 579 580 /** 581 * struct platform_nand_ctrl - controller level device structure 582 * @hwcontrol: platform specific hardware control structure 583 * @dev_ready: platform specific function to read ready/busy pin 584 * @select_chip: platform specific chip select function 585 * @cmd_ctrl: platform specific function for controlling 586 * ALE/CLE/nCE. Also used to write command and address 587 * @priv: private data to transport driver specific settings 588 * 589 * All fields are optional and depend on the hardware driver requirements 590 */ 591 struct platform_nand_ctrl { 592 void (*hwcontrol)(struct mtd_info *mtd, int cmd); 593 int (*dev_ready)(struct mtd_info *mtd); 594 void (*select_chip)(struct mtd_info *mtd, int chip); 595 void (*cmd_ctrl)(struct mtd_info *mtd, int dat, 596 unsigned int ctrl); 597 void *priv; 598 }; 599 600 /** 601 * struct platform_nand_data - container structure for platform-specific data 602 * @chip: chip level chip structure 603 * @ctrl: controller level device structure 604 */ 605 struct platform_nand_data { 606 struct platform_nand_chip chip; 607 struct platform_nand_ctrl ctrl; 608 }; 609 610 /* Some helpers to access the data structures */ 611 static inline 612 struct platform_nand_chip *get_platform_nandchip(struct mtd_info *mtd) 613 { 614 struct nand_chip *chip = mtd->priv; 615 616 return chip->priv; 617 } 618 619 #endif /* __LINUX_MTD_NAND_H */ 620