xref: /linux-6.15/drivers/usb/host/Kconfig (revision ec5499d3)
1# SPDX-License-Identifier: GPL-2.0
2#
3# USB Host Controller Drivers
4#
5comment "USB Host Controller Drivers"
6
7config USB_C67X00_HCD
8	tristate "Cypress C67x00 HCD support"
9	depends on HAS_IOMEM
10	help
11	  The Cypress C67x00 (EZ-Host/EZ-OTG) chips are dual-role
12	  host/peripheral/OTG USB controllers.
13
14	  Enable this option to support this chip in host controller mode.
15	  If unsure, say N.
16
17	  To compile this driver as a module, choose M here: the
18	  module will be called c67x00.
19
20config USB_XHCI_HCD
21	tristate "xHCI HCD (USB 3.0) support"
22	depends on HAS_DMA && HAS_IOMEM
23	help
24	  The eXtensible Host Controller Interface (xHCI) is standard for USB 3.0
25	  "SuperSpeed" host controller hardware.
26
27	  To compile this driver as a module, choose M here: the
28	  module will be called xhci-hcd.
29
30if USB_XHCI_HCD
31config USB_XHCI_DBGCAP
32	bool "xHCI support for debug capability"
33	depends on TTY
34	help
35	  Say 'Y' to enable the support for the xHCI debug capability. Make
36	  sure that your xHCI host supports the extended debug capability and
37	  you want a TTY serial device based on the xHCI debug capability
38	  before enabling this option. If unsure, say 'N'.
39
40config USB_XHCI_PCI
41	tristate
42	depends on USB_PCI
43	depends on USB_XHCI_PCI_RENESAS || !USB_XHCI_PCI_RENESAS
44	default y
45
46config USB_XHCI_PCI_RENESAS
47	tristate "Support for additional Renesas xHCI controller with firmware"
48	help
49	  Say 'Y' to enable the support for the Renesas xHCI controller with
50	  firmware. Make sure you have the firmware for the device and
51	  installed on your system for this device to work.
52	  If unsure, say 'N'.
53
54config USB_XHCI_PLATFORM
55	tristate "Generic xHCI driver for a platform device"
56	help
57	  Adds an xHCI host driver for a generic platform device, which
58	  provides a memory space and an irq.
59	  It is also a prerequisite for platform specific drivers that
60	  implement some extra quirks.
61
62	  If unsure, say N.
63
64config USB_XHCI_HISTB
65	tristate "xHCI support for HiSilicon STB SoCs"
66	depends on USB_XHCI_PLATFORM && (ARCH_HISI || COMPILE_TEST)
67	help
68	  Say 'Y' to enable the support for the xHCI host controller
69	  found in HiSilicon STB SoCs.
70
71config USB_XHCI_MTK
72	tristate "xHCI support for MediaTek SoCs"
73	select MFD_SYSCON
74	depends on (MIPS && SOC_MT7621) || ARCH_MEDIATEK || COMPILE_TEST
75	help
76	  Say 'Y' to enable the support for the xHCI host controller
77	  found in MediaTek SoCs.
78	  If unsure, say N.
79
80config USB_XHCI_MVEBU
81	tristate "xHCI support for Marvell Armada 375/38x/37xx"
82	select USB_XHCI_PLATFORM
83	depends on HAS_IOMEM
84	depends on ARCH_MVEBU || COMPILE_TEST
85	help
86	  Say 'Y' to enable the support for the xHCI host controller
87	  found in Marvell Armada 375/38x/37xx ARM SOCs.
88
89config USB_XHCI_RCAR
90	tristate "xHCI support for Renesas R-Car SoCs"
91	depends on USB_XHCI_PLATFORM
92	depends on ARCH_RENESAS || COMPILE_TEST
93	default ARCH_RENESAS
94	help
95	  Say 'Y' to enable the support for the xHCI host controller
96	  found in Renesas R-Car ARM SoCs.
97
98config USB_XHCI_RZV2M
99	bool "xHCI support for Renesas RZ/V2M SoC"
100	depends on USB_XHCI_RCAR
101	depends on ARCH_R9A09G011 || COMPILE_TEST
102	depends on USB_RZV2M_USB3DRD=y || (USB_RZV2M_USB3DRD=USB_XHCI_RCAR)
103	help
104	  Say 'Y' to enable the support for the xHCI host controller
105	  found in Renesas RZ/V2M SoC.
106
107config USB_XHCI_TEGRA
108	tristate "xHCI support for NVIDIA Tegra SoCs"
109	depends on PHY_TEGRA_XUSB
110	depends on RESET_CONTROLLER
111	select FW_LOADER
112	help
113	  Say 'Y' to enable the support for the xHCI host controller
114	  found in NVIDIA Tegra124 and later SoCs.
115
116endif # USB_XHCI_HCD
117
118config USB_EHCI_BRCMSTB
119       tristate
120
121config USB_BRCMSTB
122	tristate "Broadcom STB USB support"
123	depends on (ARCH_BRCMSTB && PHY_BRCM_USB) || COMPILE_TEST
124	select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD
125	select USB_EHCI_BRCMSTB if USB_EHCI_HCD
126	select USB_XHCI_PLATFORM if USB_XHCI_HCD
127	help
128	  Enables support for XHCI, EHCI and OHCI host controllers
129	  found in Broadcom STB SoC's.
130
131	  To compile these drivers as modules, choose M here: the
132	  modules will be called ohci-platform.ko, ehci-brcm.ko and
133	  xhci-plat-hcd.ko
134
135	  Disabling this will keep the controllers and corresponding
136	  PHYs powered down.
137
138config USB_EHCI_HCD
139	tristate "EHCI HCD (USB 2.0) support"
140	depends on HAS_DMA && HAS_IOMEM
141	help
142	  The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0
143	  "high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware.
144	  If your USB host controller supports USB 2.0, you will likely want to
145	  configure this Host Controller Driver.
146
147	  EHCI controllers are packaged with "companion" host controllers (OHCI
148	  or UHCI) to handle USB 1.1 devices connected to root hub ports.  Ports
149	  will connect to EHCI if the device is high speed, otherwise they
150	  connect to a companion controller.  If you configure EHCI, you should
151	  probably configure the OHCI (for NEC and some other vendors) USB Host
152	  Controller Driver or UHCI (for Via motherboards) Host Controller
153	  Driver too.
154
155	  You may want to read <file:Documentation/usb/ehci.rst>.
156
157	  To compile this driver as a module, choose M here: the
158	  module will be called ehci-hcd.
159
160config USB_EHCI_ROOT_HUB_TT
161	bool "Root Hub Transaction Translators"
162	depends on USB_EHCI_HCD
163	help
164	  Some EHCI chips have vendor-specific extensions to integrate
165	  transaction translators, so that no OHCI or UHCI companion
166	  controller is needed.  It's safe to say "y" even if your
167	  controller doesn't support this feature.
168
169	  This supports the EHCI implementation that's originally
170	  from ARC, and has since changed hands a few times.
171
172config USB_EHCI_TT_NEWSCHED
173	bool "Improved Transaction Translator scheduling"
174	depends on USB_EHCI_HCD
175	default y
176	help
177	  This changes the periodic scheduling code to fill more of the low
178	  and full speed bandwidth available from the Transaction Translator
179	  (TT) in USB 2.0 hubs.  Without this, only one transfer will be
180	  issued in each microframe, significantly reducing the number of
181	  periodic low/fullspeed transfers possible.
182
183	  If you have multiple periodic low/fullspeed devices connected to a
184	  highspeed USB hub which is connected to a highspeed USB Host
185	  Controller, and some of those devices will not work correctly
186	  (possibly due to "ENOSPC" or "-28" errors), say Y.  Conversely, if
187	  you have only one such device and it doesn't work, you could try
188	  saying N.
189
190	  If unsure, say Y.
191
192if USB_EHCI_HCD
193
194config USB_EHCI_PCI
195	tristate
196	depends on USB_PCI
197	default y
198
199config XPS_USB_HCD_XILINX
200	bool "Use Xilinx usb host EHCI controller core"
201	depends on (PPC32 || MICROBLAZE)
202	select USB_EHCI_BIG_ENDIAN_DESC
203	select USB_EHCI_BIG_ENDIAN_MMIO
204	help
205		Xilinx xps USB host controller core is EHCI compliant and has
206		transaction translator built-in. It can be configured to either
207		support both high speed and full speed devices, or high speed
208		devices only.
209
210config USB_EHCI_FSL
211	tristate "Support for Freescale on-chip EHCI USB controller"
212	select USB_EHCI_ROOT_HUB_TT
213	help
214	  Variation of ARC USB block used in some Freescale chips.
215
216config USB_EHCI_HCD_NPCM7XX
217	tristate "Support for Nuvoton NPCM on-chip EHCI USB controller"
218	depends on (USB_EHCI_HCD && ARCH_NPCM) || COMPILE_TEST
219	default y if (USB_EHCI_HCD && ARCH_NPCM)
220	help
221	  Enables support for the on-chip EHCI controller on
222	  Nuvoton NPCM chips.
223
224config USB_EHCI_HCD_OMAP
225	tristate "EHCI support for OMAP3 and later chips"
226	depends on ARCH_OMAP || COMPILE_TEST
227	depends on NOP_USB_XCEIV
228	default y
229	help
230	  Enables support for the on-chip EHCI controller on
231	  OMAP3 and later chips.
232
233config USB_EHCI_HCD_ORION
234	tristate  "Support for Marvell EBU on-chip EHCI USB controller"
235	depends on USB_EHCI_HCD && (PLAT_ORION || ARCH_MVEBU || COMPILE_TEST)
236	default y if (PLAT_ORION || ARCH_MVEBU)
237	help
238	  Enables support for the on-chip EHCI controller on Marvell's
239	  embedded ARM SoCs, including Orion, Kirkwood, Dove, Armada XP,
240	  Armada 370.  This is different from the EHCI implementation
241	  on Marvell's mobile PXA and MMP SoC, see "EHCI support for
242	  Marvell PXA/MMP USB controller" for those.
243
244config USB_EHCI_HCD_SPEAR
245	tristate "Support for ST SPEAr on-chip EHCI USB controller"
246	depends on USB_EHCI_HCD && (PLAT_SPEAR || COMPILE_TEST)
247	default y if PLAT_SPEAR
248	help
249	  Enables support for the on-chip EHCI controller on
250	  ST SPEAr chips.
251
252config USB_EHCI_HCD_STI
253	tristate "Support for ST STiHxxx on-chip EHCI USB controller"
254	depends on (ARCH_STI || COMPILE_TEST) && OF
255	select GENERIC_PHY
256	select USB_EHCI_HCD_PLATFORM
257	help
258	  Enable support for the on-chip EHCI controller found on
259	  STMicroelectronics consumer electronics SoC's.
260
261config USB_EHCI_HCD_AT91
262	tristate  "Support for Atmel on-chip EHCI USB controller"
263	depends on USB_EHCI_HCD && (ARCH_AT91 || COMPILE_TEST)
264	default y if ARCH_AT91
265	help
266	  Enables support for the on-chip EHCI controller on
267	  Atmel chips.
268
269config USB_EHCI_TEGRA
270	tristate "NVIDIA Tegra HCD support"
271	depends on ARCH_TEGRA
272	select USB_CHIPIDEA
273	select USB_CHIPIDEA_HOST
274	select USB_CHIPIDEA_TEGRA
275	select USB_GADGET
276	help
277	  This option is deprecated now and the driver was removed, use
278	  USB_CHIPIDEA_TEGRA instead.
279
280	  Enable support for the internal USB Host Controllers
281	  found in NVIDIA Tegra SoCs. The controllers are EHCI compliant.
282
283config USB_EHCI_HCD_PPC_OF
284	bool "EHCI support for PPC USB controller on OF platform bus"
285	depends on PPC
286	default y
287	help
288	  Enables support for the USB controller present on the PowerPC
289	  OpenFirmware platform bus.
290
291config USB_EHCI_SH
292	bool "EHCI support for SuperH USB controller"
293	depends on SUPERH || COMPILE_TEST
294	help
295	  Enables support for the on-chip EHCI controller on the SuperH.
296	  If you use the PCI EHCI controller, this option is not necessary.
297
298config USB_EHCI_EXYNOS
299	tristate "EHCI support for Samsung S5P/Exynos SoC Series"
300	depends on ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST
301	help
302	  Enable support for the Samsung S5Pv210 and Exynos SOC's on-chip EHCI
303	  controller.
304
305config USB_EHCI_MV
306	tristate "EHCI support for Marvell PXA/MMP USB controller"
307	depends on ARCH_PXA || ARCH_MMP || COMPILE_TEST
308	select USB_EHCI_ROOT_HUB_TT
309	help
310	  Enables support for Marvell (including PXA and MMP series) on-chip
311	  USB SPH and OTG controller. SPH is a single port host, and it can
312	  only be EHCI host. OTG is controller that can switch to host mode.
313	  Note that this driver will not work on Marvell's other EHCI
314	  controller used by the EBU-type SoCs including Orion, Kirkwood,
315	  Dova, Armada 370 and Armada XP. See "Support for Marvell EBU
316	  on-chip EHCI USB controller" for those.
317
318config USB_OCTEON_HCD
319	tristate "Cavium Networks Octeon USB support"
320	depends on CAVIUM_OCTEON_SOC && USB
321	help
322	  This driver supports USB host controller on some Cavium
323	  Networks' products in the Octeon family.
324
325	  To compile this driver as a module, choose M here. The module
326	  will be called octeon-hcd.
327
328config USB_CNS3XXX_EHCI
329	bool "Cavium CNS3XXX EHCI Module (DEPRECATED)"
330	depends on ARCH_CNS3XXX || COMPILE_TEST
331	select USB_EHCI_HCD_PLATFORM
332	help
333	  This option is deprecated now and the driver was removed, use
334	  USB_EHCI_HCD_PLATFORM instead.
335
336	  Enable support for the CNS3XXX SOC's on-chip EHCI controller.
337	  It is needed for high-speed (480Mbit/sec) USB 2.0 device
338	  support.
339
340config USB_EHCI_HCD_PLATFORM
341	tristate "Generic EHCI driver for a platform device"
342	help
343	  Adds an EHCI host driver for a generic platform device, which
344	  provides a memory space and an irq.
345
346	  If unsure, say N.
347
348config USB_OCTEON_EHCI
349	bool "Octeon on-chip EHCI support (DEPRECATED)"
350	depends on CAVIUM_OCTEON_SOC
351	select USB_EHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
352	select USB_EHCI_HCD_PLATFORM
353	help
354	  This option is deprecated now and the driver was removed, use
355	  USB_EHCI_HCD_PLATFORM instead.
356
357	  Enable support for the Octeon II SOC's on-chip EHCI
358	  controller.  It is needed for high-speed (480Mbit/sec)
359	  USB 2.0 device support.  All CN6XXX based chips with USB are
360	  supported.
361
362endif # USB_EHCI_HCD
363
364config USB_OXU210HP_HCD
365	tristate "OXU210HP HCD support"
366	depends on HAS_IOMEM
367	help
368	  The OXU210HP is an USB host/OTG/device controller. Enable this
369	  option if your board has this chip. If unsure, say N.
370
371	  This driver does not support isochronous transfers and doesn't
372	  implement OTG nor USB device controllers.
373
374	  To compile this driver as a module, choose M here: the
375	  module will be called oxu210hp-hcd.
376
377config USB_ISP116X_HCD
378	tristate "ISP116X HCD support"
379	depends on HAS_IOMEM
380	help
381	  The ISP1160 and ISP1161 chips are USB host controllers. Enable this
382	  option if your board has this chip. If unsure, say N.
383
384	  This driver does not support isochronous transfers.
385
386	  To compile this driver as a module, choose M here: the
387	  module will be called isp116x-hcd.
388
389config USB_ISP1362_HCD
390	tristate "ISP1362 HCD support"
391	depends on HAS_IOMEM
392	depends on COMPILE_TEST # nothing uses this
393	help
394	  Supports the Philips ISP1362 chip as a host controller
395
396	  This driver does not support isochronous transfers.
397
398	  To compile this driver as a module, choose M here: the
399	  module will be called isp1362-hcd.
400
401config USB_MAX3421_HCD
402	tristate "MAX3421 HCD (USB-over-SPI) support"
403	depends on USB && SPI
404	help
405	  The Maxim MAX3421E chip supports standard USB 2.0-compliant
406	  full-speed devices either in host or peripheral mode.  This
407	  driver supports the host-mode of the MAX3421E only.
408
409	  To compile this driver as a module, choose M here: the module will
410	  be called max3421-hcd.
411
412config USB_OHCI_HCD
413	tristate "OHCI HCD (USB 1.1) support"
414	depends on HAS_DMA && HAS_IOMEM
415	help
416	  The Open Host Controller Interface (OHCI) is a standard for accessing
417	  USB 1.1 host controller hardware.  It does more in hardware than Intel's
418	  UHCI specification.  If your USB host controller follows the OHCI spec,
419	  say Y.  On most non-x86 systems, and on x86 hardware that's not using a
420	  USB controller from Intel or VIA, this is appropriate.  If your host
421	  controller doesn't use PCI, this is probably appropriate.  For a PCI
422	  based system where you're not sure, the "lspci -v" entry will list the
423	  right "prog-if" for your USB controller(s):  EHCI, OHCI, or UHCI.
424
425	  To compile this driver as a module, choose M here: the
426	  module will be called ohci-hcd.
427
428if USB_OHCI_HCD
429
430config USB_OHCI_HCD_OMAP1
431	tristate "OHCI support for OMAP1/2 chips"
432	depends on ARCH_OMAP1
433	depends on ISP1301_OMAP || !(MACH_OMAP_H2 || MACH_OMAP_H3)
434	default y
435	help
436	  Enables support for the OHCI controller on OMAP1/2 chips.
437
438config USB_OHCI_HCD_SPEAR
439	tristate "Support for ST SPEAr on-chip OHCI USB controller"
440	depends on USB_OHCI_HCD && (PLAT_SPEAR || COMPILE_TEST)
441	default y if PLAT_SPEAR
442	help
443	  Enables support for the on-chip OHCI controller on
444	  ST SPEAr chips.
445
446config USB_OHCI_HCD_STI
447	tristate "Support for ST STiHxxx on-chip OHCI USB controller"
448	depends on (ARCH_STI || COMPILE_TEST) && OF
449	select GENERIC_PHY
450	select USB_OHCI_HCD_PLATFORM
451	help
452	  Enable support for the on-chip OHCI controller found on
453	  STMicroelectronics consumer electronics SoC's.
454
455config USB_OHCI_HCD_S3C2410
456	tristate "OHCI support for Samsung S3C24xx/S3C64xx SoC series"
457	depends on USB_OHCI_HCD && (ARCH_S3C24XX || ARCH_S3C64XX || COMPILE_TEST)
458	default y if (ARCH_S3C24XX || ARCH_S3C64XX)
459	help
460	  Enables support for the on-chip OHCI controller on
461	  S3C24xx/S3C64xx chips.
462
463config USB_OHCI_HCD_LPC32XX
464	tristate "Support for LPC on-chip OHCI USB controller"
465	depends on USB_OHCI_HCD
466	depends on ARCH_LPC32XX || COMPILE_TEST
467	depends on USB_ISP1301
468	default y
469	help
470	  Enables support for the on-chip OHCI controller on
471	  NXP chips.
472
473config USB_OHCI_HCD_PXA27X
474	tristate "Support for PXA27X/PXA3XX on-chip OHCI USB controller"
475	depends on USB_OHCI_HCD && (PXA27x || PXA3xx)
476	default y
477	help
478	  Enables support for the on-chip OHCI controller on
479	  PXA27x/PXA3xx chips.
480
481config USB_OHCI_HCD_AT91
482	tristate "Support for Atmel on-chip OHCI USB controller"
483	depends on USB_OHCI_HCD && (ARCH_AT91 || COMPILE_TEST) && OF
484	default y if ARCH_AT91
485	help
486	  Enables support for the on-chip OHCI controller on
487	  Atmel chips.
488
489config USB_OHCI_HCD_OMAP3
490	tristate "OHCI support for OMAP3 and later chips"
491	depends on ARCH_OMAP3 || ARCH_OMAP4 || SOC_OMAP5 || COMPILE_TEST
492	select USB_OHCI_HCD_PLATFORM
493	default y if ARCH_OMAP3 || ARCH_OMAP4 || SOC_OMAP5
494	help
495	  This option is deprecated now and the driver was removed, use
496	  USB_OHCI_HCD_PLATFORM instead.
497
498	  Enables support for the on-chip OHCI controller on
499	  OMAP3 and later chips.
500
501config USB_OHCI_HCD_DAVINCI
502	tristate "OHCI support for TI DaVinci DA8xx"
503	depends on ARCH_DAVINCI_DA8XX || COMPILE_TEST
504	depends on USB_OHCI_HCD
505	select PHY_DA8XX_USB
506	default y if ARCH_DAVINCI_DA8XX
507	help
508	  Enables support for the DaVinci DA8xx integrated OHCI
509	  controller. This driver cannot currently be a loadable
510	  module because it lacks a proper PHY abstraction.
511
512config USB_OHCI_HCD_PPC_OF_BE
513	bool "OHCI support for OF platform bus (big endian)"
514	depends on PPC
515	select USB_OHCI_BIG_ENDIAN_DESC
516	select USB_OHCI_BIG_ENDIAN_MMIO
517	help
518	  Enables support for big-endian USB controllers present on the
519	  OpenFirmware platform bus.
520
521config USB_OHCI_HCD_PPC_OF_LE
522	bool "OHCI support for OF platform bus (little endian)"
523	depends on PPC
524	select USB_OHCI_LITTLE_ENDIAN
525	help
526	  Enables support for little-endian USB controllers present on the
527	  OpenFirmware platform bus.
528
529config USB_OHCI_HCD_PPC_OF
530	bool
531	depends on PPC
532	default USB_OHCI_HCD_PPC_OF_BE || USB_OHCI_HCD_PPC_OF_LE
533
534config USB_OHCI_HCD_PCI
535	tristate "OHCI support for PCI-bus USB controllers"
536	depends on USB_PCI
537	default y
538	select USB_OHCI_LITTLE_ENDIAN
539	help
540	  Enables support for PCI-bus plug-in USB controller cards.
541	  If unsure, say Y.
542
543config USB_OHCI_HCD_SSB
544	bool "OHCI support for Broadcom SSB OHCI core (DEPRECATED)"
545	depends on (SSB = y || SSB = USB_OHCI_HCD)
546	select USB_HCD_SSB
547	select USB_OHCI_HCD_PLATFORM
548	help
549	  This option is deprecated now and the driver was removed, use
550	  USB_HCD_SSB and USB_OHCI_HCD_PLATFORM instead.
551
552	  Support for the Sonics Silicon Backplane (SSB) attached
553	  Broadcom USB OHCI core.
554
555	  This device is present in some embedded devices with
556	  Broadcom based SSB bus.
557
558	  If unsure, say N.
559
560config USB_OHCI_SH
561	bool "OHCI support for SuperH USB controller (DEPRECATED)"
562	depends on SUPERH || COMPILE_TEST
563	select USB_OHCI_HCD_PLATFORM
564	help
565	  This option is deprecated now and the driver was removed, use
566	  USB_OHCI_HCD_PLATFORM instead.
567
568	  Enables support for the on-chip OHCI controller on the SuperH.
569	  If you use the PCI OHCI controller, this option is not necessary.
570
571config USB_OHCI_EXYNOS
572	tristate "OHCI support for Samsung S5P/Exynos SoC Series"
573	depends on ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST
574	help
575	  Enable support for the Samsung S5Pv210 and Exynos SOC's on-chip OHCI
576	  controller.
577
578config USB_CNS3XXX_OHCI
579	bool "Cavium CNS3XXX OHCI Module (DEPRECATED)"
580	depends on ARCH_CNS3XXX || COMPILE_TEST
581	select USB_OHCI_HCD_PLATFORM
582	help
583	  This option is deprecated now and the driver was removed, use
584	  USB_OHCI_HCD_PLATFORM instead.
585
586	  Enable support for the CNS3XXX SOC's on-chip OHCI controller.
587	  It is needed for low-speed USB 1.0 device support.
588
589config USB_OHCI_HCD_PLATFORM
590	tristate "Generic OHCI driver for a platform device"
591	help
592	  Adds an OHCI host driver for a generic platform device, which
593	  provides a memory space and an irq.
594
595	  If unsure, say N.
596
597config USB_OCTEON_OHCI
598	bool "Octeon on-chip OHCI support (DEPRECATED)"
599	depends on CAVIUM_OCTEON_SOC
600	default USB_OCTEON_EHCI
601	select USB_OHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
602	select USB_OHCI_LITTLE_ENDIAN
603	select USB_OHCI_HCD_PLATFORM
604	help
605	  This option is deprecated now and the driver was removed, use
606	  USB_OHCI_HCD_PLATFORM instead.
607
608	  Enable support for the Octeon II SOC's on-chip OHCI
609	  controller.  It is needed for low-speed USB 1.0 device
610	  support.  All CN6XXX based chips with USB are supported.
611
612endif # USB_OHCI_HCD
613
614config USB_UHCI_HCD
615	tristate "UHCI HCD (most Intel and VIA) support"
616	depends on USB_PCI || USB_UHCI_SUPPORT_NON_PCI_HC
617	help
618	  The Universal Host Controller Interface is a standard by Intel for
619	  accessing the USB hardware in the PC (which is also called the USB
620	  host controller). If your USB host controller conforms to this
621	  standard, you may want to say Y, but see below. All recent boards
622	  with Intel PCI chipsets (like intel 430TX, 440FX, 440LX, 440BX,
623	  i810, i820) conform to this standard. Also all VIA PCI chipsets
624	  (like VIA VP2, VP3, MVP3, Apollo Pro, Apollo Pro II or Apollo Pro
625	  133) and LEON/GRLIB SoCs with the GRUSBHC controller.
626	  If unsure, say Y.
627
628	  To compile this driver as a module, choose M here: the
629	  module will be called uhci-hcd.
630
631config USB_UHCI_SUPPORT_NON_PCI_HC
632	bool
633	default y if (SPARC_LEON || USB_UHCI_PLATFORM)
634
635config USB_UHCI_PLATFORM
636	bool
637	default y if (ARCH_VT8500 || ARCH_ASPEED)
638
639config USB_UHCI_ASPEED
640	bool
641	default y if ARCH_ASPEED
642
643config USB_FHCI_HCD
644	tristate "Freescale QE USB Host Controller support"
645	depends on OF_GPIO && QE_GPIO && QUICC_ENGINE
646	select FSL_GTM
647	select QE_USB
648	help
649	  This driver enables support for Freescale QE USB Host Controller
650	  (as found on MPC8360 and MPC8323 processors), the driver supports
651	  Full and Low Speed USB.
652
653config FHCI_DEBUG
654	bool "Freescale QE USB Host Controller debug support"
655	depends on USB_FHCI_HCD && DEBUG_FS
656	help
657	  Say "y" to see some FHCI debug information and statistics
658	  through debugfs.
659
660config USB_U132_HCD
661	tristate "Elan U132 Adapter Host Controller"
662	depends on USB_FTDI_ELAN
663	help
664	  The U132 adapter is a USB to CardBus adapter specifically designed
665	  for PC cards that contain an OHCI host controller. Typical PC cards
666	  are the Orange Mobile 3G Option GlobeTrotter Fusion card. The U132
667	  adapter will *NOT* work with PC cards that do not contain an OHCI
668	  controller.
669
670	  For those PC cards that contain multiple OHCI controllers only the
671	  first one is used.
672
673	  The driver consists of two modules, the "ftdi-elan" module is a
674	  USB client driver that interfaces to the FTDI chip within ELAN's
675	  USB-to-PCMCIA adapter, and this "u132-hcd" module is a USB host
676	  controller driver that talks to the OHCI controller within the
677	  CardBus cards that are inserted in the U132 adapter.
678
679	  This driver has been tested with a CardBus OHCI USB adapter, and
680	  worked with a USB PEN Drive inserted into the first USB port of
681	  the PCCARD. A rather pointless thing to do, but useful for testing.
682
683	  It is safe to say M here.
684
685	  See also <http://www.elandigitalsystems.com/support/ufaq/u132linux.php>
686
687config USB_SL811_HCD
688	tristate "SL811HS HCD support"
689	depends on HAS_IOMEM
690	help
691	  The SL811HS is a single-port USB controller that supports either
692	  host side or peripheral side roles.  Enable this option if your
693	  board has this chip, and you want to use it as a host controller.
694	  If unsure, say N.
695
696	  To compile this driver as a module, choose M here: the
697	  module will be called sl811-hcd.
698
699config USB_SL811_HCD_ISO
700	bool "partial ISO support"
701	depends on USB_SL811_HCD
702	help
703	  The driver doesn't support iso_frame_desc (yet), but for some simple
704	  devices that just queue one ISO frame per URB, then ISO transfers
705	  "should" work using the normal urb status fields.
706
707	  If unsure, say N.
708
709config USB_SL811_CS
710	tristate "CF/PCMCIA support for SL811HS HCD"
711	depends on USB_SL811_HCD && PCMCIA
712	help
713	  Wraps a PCMCIA driver around the SL811HS HCD, supporting the RATOC
714	  REX-CFU1U CF card (often used with PDAs).  If unsure, say N.
715
716	  To compile this driver as a module, choose M here: the
717	  module will be called "sl811_cs".
718
719config USB_R8A66597_HCD
720	tristate "R8A66597 HCD support"
721	depends on HAS_IOMEM
722	help
723	  The R8A66597 is a USB 2.0 host and peripheral controller.
724
725	  Enable this option if your board has this chip, and you want
726	  to use it as a host controller.  If unsure, say N.
727
728	  To compile this driver as a module, choose M here: the
729	  module will be called r8a66597-hcd.
730
731config USB_RENESAS_USBHS_HCD
732	tristate "Renesas USBHS HCD support"
733	depends on USB_RENESAS_USBHS
734	help
735	  The Renesas USBHS is a USB 2.0 host and peripheral controller.
736
737	  Enable this option if your board has this chip, and you want
738	  to use it as a host controller.  If unsure, say N.
739
740	  To compile this driver as a module, choose M here: the
741	  module will be called renesas-usbhs.
742
743config USB_HCD_BCMA
744	tristate "BCMA usb host driver"
745	depends on BCMA
746	select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD
747	select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD
748	help
749	  Enable support for the EHCI and OCHI host controller on an bcma bus.
750	  It converts the bcma driver into two platform device drivers
751	  for ehci and ohci.
752
753	  If unsure, say N.
754
755config USB_HCD_SSB
756	tristate "SSB usb host driver"
757	depends on SSB
758	select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD
759	select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD
760	help
761	  Enable support for the EHCI and OCHI host controller on an bcma bus.
762	  It converts the bcma driver into two platform device drivers
763	  for ehci and ohci.
764
765	  If unsure, say N.
766
767config USB_HCD_TEST_MODE
768	bool "HCD test mode support"
769	help
770	  Say 'Y' to enable additional software test modes that may be
771	  supported by the host controller drivers.
772
773	  One such test mode is the Embedded High-speed Host Electrical Test
774	  (EHSET) for EHCI host controller hardware, specifically the "Single
775	  Step Set Feature" test.  Typically this will be enabled for On-the-Go
776	  or embedded hosts that need to undergo USB-IF compliance testing with
777	  the aid of special testing hardware.  In the future, this may expand
778	  to include other tests that require support from a HCD driver.
779
780	  This option is of interest only to developers who need to validate
781	  their USB hardware designs.  It is not needed for normal use.  If
782	  unsure, say N.
783
784config USB_XEN_HCD
785	tristate "Xen usb virtual host driver"
786	depends on XEN
787	select XEN_XENBUS_FRONTEND
788	help
789	  The Xen usb virtual host driver serves as a frontend driver enabling
790	  a Xen guest system to access USB Devices passed through to the guest
791	  by the Xen host (usually Dom0).
792	  Only needed if the kernel is running in a Xen guest and generic
793	  access to a USB device is needed.
794