xref: /linux-6.15/drivers/usb/host/Kconfig (revision 4f6dfc21)
1# SPDX-License-Identifier: GPL-2.0
2#
3# USB Host Controller Drivers
4#
5comment "USB Host Controller Drivers"
6
7config USB_C67X00_HCD
8	tristate "Cypress C67x00 HCD support"
9	depends on HAS_IOMEM
10	help
11	  The Cypress C67x00 (EZ-Host/EZ-OTG) chips are dual-role
12	  host/peripheral/OTG USB controllers.
13
14	  Enable this option to support this chip in host controller mode.
15	  If unsure, say N.
16
17	  To compile this driver as a module, choose M here: the
18	  module will be called c67x00.
19
20config USB_XHCI_HCD
21	tristate "xHCI HCD (USB 3.0) support"
22	depends on HAS_DMA && HAS_IOMEM
23	help
24	  The eXtensible Host Controller Interface (xHCI) is standard for USB 3.0
25	  "SuperSpeed" host controller hardware.
26
27	  To compile this driver as a module, choose M here: the
28	  module will be called xhci-hcd.
29
30if USB_XHCI_HCD
31config USB_XHCI_DBGCAP
32	bool "xHCI support for debug capability"
33	depends on TTY
34	help
35	  Say 'Y' to enable the support for the xHCI debug capability. Make
36	  sure that your xHCI host supports the extended debug capability and
37	  you want a TTY serial device based on the xHCI debug capability
38	  before enabling this option. If unsure, say 'N'.
39
40config USB_XHCI_PCI
41	tristate
42	depends on USB_PCI
43	depends on USB_XHCI_PCI_RENESAS || !USB_XHCI_PCI_RENESAS
44	default y
45
46config USB_XHCI_PCI_RENESAS
47	tristate "Support for additional Renesas xHCI controller with firmware"
48	help
49	  Say 'Y' to enable the support for the Renesas xHCI controller with
50	  firmware. Make sure you have the firmware for the device and
51	  installed on your system for this device to work.
52	  If unsure, say 'N'.
53
54config USB_XHCI_PLATFORM
55	tristate "Generic xHCI driver for a platform device"
56	help
57	  Adds an xHCI host driver for a generic platform device, which
58	  provides a memory space and an irq.
59	  It is also a prerequisite for platform specific drivers that
60	  implement some extra quirks.
61
62	  If unsure, say N.
63
64config USB_XHCI_HISTB
65	tristate "xHCI support for HiSilicon STB SoCs"
66	depends on USB_XHCI_PLATFORM && (ARCH_HISI || COMPILE_TEST)
67	help
68	  Say 'Y' to enable the support for the xHCI host controller
69	  found in HiSilicon STB SoCs.
70
71config USB_XHCI_MTK
72	tristate "xHCI support for MediaTek SoCs"
73	select MFD_SYSCON
74	depends on (MIPS && SOC_MT7621) || ARCH_MEDIATEK || COMPILE_TEST
75	help
76	  Say 'Y' to enable the support for the xHCI host controller
77	  found in MediaTek SoCs.
78	  If unsure, say N.
79
80config USB_XHCI_MVEBU
81	tristate "xHCI support for Marvell Armada 375/38x/37xx"
82	select USB_XHCI_PLATFORM
83	depends on HAS_IOMEM
84	depends on ARCH_MVEBU || COMPILE_TEST
85	help
86	  Say 'Y' to enable the support for the xHCI host controller
87	  found in Marvell Armada 375/38x/37xx ARM SOCs.
88
89config USB_XHCI_RCAR
90	tristate "xHCI support for Renesas R-Car SoCs"
91	depends on USB_XHCI_PLATFORM
92	depends on ARCH_RENESAS || COMPILE_TEST
93	default ARCH_RENESAS
94	help
95	  Say 'Y' to enable the support for the xHCI host controller
96	  found in Renesas R-Car ARM SoCs.
97
98config USB_XHCI_RZV2M
99	bool "xHCI support for Renesas RZ/V2M SoC"
100	depends on USB_XHCI_RCAR
101	depends on ARCH_R9A09G011 || COMPILE_TEST
102	depends on USB_RZV2M_USB3DRD=y || (USB_RZV2M_USB3DRD=USB_XHCI_RCAR)
103	help
104	  Say 'Y' to enable the support for the xHCI host controller
105	  found in Renesas RZ/V2M SoC.
106
107config USB_XHCI_TEGRA
108	tristate "xHCI support for NVIDIA Tegra SoCs"
109	depends on PHY_TEGRA_XUSB
110	depends on RESET_CONTROLLER
111	select FW_LOADER
112	help
113	  Say 'Y' to enable the support for the xHCI host controller
114	  found in NVIDIA Tegra124 and later SoCs.
115
116endif # USB_XHCI_HCD
117
118config USB_EHCI_BRCMSTB
119       tristate
120
121config USB_BRCMSTB
122	tristate "Broadcom STB USB support"
123	depends on (ARCH_BRCMSTB && PHY_BRCM_USB) || COMPILE_TEST
124	select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD
125	select USB_EHCI_BRCMSTB if USB_EHCI_HCD
126	select USB_XHCI_PLATFORM if USB_XHCI_HCD
127	help
128	  Enables support for XHCI, EHCI and OHCI host controllers
129	  found in Broadcom STB SoC's.
130
131	  To compile these drivers as modules, choose M here: the
132	  modules will be called ohci-platform.ko, ehci-brcm.ko and
133	  xhci-plat-hcd.ko
134
135	  Disabling this will keep the controllers and corresponding
136	  PHYs powered down.
137
138config USB_EHCI_HCD
139	tristate "EHCI HCD (USB 2.0) support"
140	depends on HAS_DMA && HAS_IOMEM
141	help
142	  The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0
143	  "high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware.
144	  If your USB host controller supports USB 2.0, you will likely want to
145	  configure this Host Controller Driver.
146
147	  EHCI controllers are packaged with "companion" host controllers (OHCI
148	  or UHCI) to handle USB 1.1 devices connected to root hub ports.  Ports
149	  will connect to EHCI if the device is high speed, otherwise they
150	  connect to a companion controller.  If you configure EHCI, you should
151	  probably configure the OHCI (for NEC and some other vendors) USB Host
152	  Controller Driver or UHCI (for Via motherboards) Host Controller
153	  Driver too.
154
155	  You may want to read <file:Documentation/usb/ehci.rst>.
156
157	  To compile this driver as a module, choose M here: the
158	  module will be called ehci-hcd.
159
160config USB_EHCI_ROOT_HUB_TT
161	bool "Root Hub Transaction Translators"
162	depends on USB_EHCI_HCD
163	help
164	  Some EHCI chips have vendor-specific extensions to integrate
165	  transaction translators, so that no OHCI or UHCI companion
166	  controller is needed.  It's safe to say "y" even if your
167	  controller doesn't support this feature.
168
169	  This supports the EHCI implementation that's originally
170	  from ARC, and has since changed hands a few times.
171
172config USB_EHCI_TT_NEWSCHED
173	bool "Improved Transaction Translator scheduling"
174	depends on USB_EHCI_HCD
175	default y
176	help
177	  This changes the periodic scheduling code to fill more of the low
178	  and full speed bandwidth available from the Transaction Translator
179	  (TT) in USB 2.0 hubs.  Without this, only one transfer will be
180	  issued in each microframe, significantly reducing the number of
181	  periodic low/fullspeed transfers possible.
182
183	  If you have multiple periodic low/fullspeed devices connected to a
184	  highspeed USB hub which is connected to a highspeed USB Host
185	  Controller, and some of those devices will not work correctly
186	  (possibly due to "ENOSPC" or "-28" errors), say Y.  Conversely, if
187	  you have only one such device and it doesn't work, you could try
188	  saying N.
189
190	  If unsure, say Y.
191
192if USB_EHCI_HCD
193
194config USB_EHCI_PCI
195	tristate
196	depends on USB_PCI
197	default y
198
199config XPS_USB_HCD_XILINX
200	bool "Use Xilinx usb host EHCI controller core"
201	depends on (PPC32 || MICROBLAZE)
202	select USB_EHCI_BIG_ENDIAN_DESC
203	select USB_EHCI_BIG_ENDIAN_MMIO
204	help
205		Xilinx xps USB host controller core is EHCI compliant and has
206		transaction translator built-in. It can be configured to either
207		support both high speed and full speed devices, or high speed
208		devices only.
209
210config USB_EHCI_FSL
211	tristate "Support for Freescale on-chip EHCI USB controller"
212	select USB_EHCI_ROOT_HUB_TT
213	help
214	  Variation of ARC USB block used in some Freescale chips.
215
216config USB_EHCI_HCD_NPCM7XX
217	tristate "Support for Nuvoton NPCM on-chip EHCI USB controller"
218	depends on (USB_EHCI_HCD && ARCH_NPCM) || COMPILE_TEST
219	default y if (USB_EHCI_HCD && ARCH_NPCM)
220	help
221	  Enables support for the on-chip EHCI controller on
222	  Nuvoton NPCM chips.
223
224config USB_EHCI_HCD_OMAP
225	tristate "EHCI support for OMAP3 and later chips"
226	depends on ARCH_OMAP || COMPILE_TEST
227	depends on NOP_USB_XCEIV
228	default y
229	help
230	  Enables support for the on-chip EHCI controller on
231	  OMAP3 and later chips.
232
233config USB_EHCI_HCD_ORION
234	tristate  "Support for Marvell EBU on-chip EHCI USB controller"
235	depends on USB_EHCI_HCD && (PLAT_ORION || ARCH_MVEBU || COMPILE_TEST)
236	default y if (PLAT_ORION || ARCH_MVEBU)
237	help
238	  Enables support for the on-chip EHCI controller on Marvell's
239	  embedded ARM SoCs, including Orion, Kirkwood, Dove, Armada XP,
240	  Armada 370.  This is different from the EHCI implementation
241	  on Marvell's mobile PXA and MMP SoC, see "EHCI support for
242	  Marvell PXA/MMP USB controller" for those.
243
244config USB_EHCI_HCD_SPEAR
245	tristate "Support for ST SPEAr on-chip EHCI USB controller"
246	depends on USB_EHCI_HCD && (PLAT_SPEAR || COMPILE_TEST)
247	default y if PLAT_SPEAR
248	help
249	  Enables support for the on-chip EHCI controller on
250	  ST SPEAr chips.
251
252config USB_EHCI_HCD_STI
253	tristate "Support for ST STiHxxx on-chip EHCI USB controller"
254	depends on (ARCH_STI || COMPILE_TEST) && OF
255	select GENERIC_PHY
256	select USB_EHCI_HCD_PLATFORM
257	help
258	  Enable support for the on-chip EHCI controller found on
259	  STMicroelectronics consumer electronics SoC's.
260
261config USB_EHCI_HCD_AT91
262	tristate  "Support for Atmel on-chip EHCI USB controller"
263	depends on USB_EHCI_HCD && (ARCH_AT91 || COMPILE_TEST)
264	default y if ARCH_AT91
265	help
266	  Enables support for the on-chip EHCI controller on
267	  Atmel chips.
268
269config USB_EHCI_TEGRA
270	tristate "NVIDIA Tegra HCD support"
271	depends on ARCH_TEGRA
272	select USB_CHIPIDEA
273	select USB_CHIPIDEA_HOST
274	select USB_CHIPIDEA_TEGRA
275	select USB_GADGET
276	help
277	  This option is deprecated now and the driver was removed, use
278	  USB_CHIPIDEA_TEGRA instead.
279
280	  Enable support for the internal USB Host Controllers
281	  found in NVIDIA Tegra SoCs. The controllers are EHCI compliant.
282
283config USB_EHCI_HCD_PPC_OF
284	bool "EHCI support for PPC USB controller on OF platform bus"
285	depends on PPC
286	default y
287	help
288	  Enables support for the USB controller present on the PowerPC
289	  OpenFirmware platform bus.
290
291config USB_EHCI_SH
292	bool "EHCI support for SuperH USB controller"
293	depends on SUPERH || COMPILE_TEST
294	help
295	  Enables support for the on-chip EHCI controller on the SuperH.
296	  If you use the PCI EHCI controller, this option is not necessary.
297
298config USB_EHCI_EXYNOS
299	tristate "EHCI support for Samsung S5P/Exynos SoC Series"
300	depends on ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST
301	help
302	  Enable support for the Samsung S5Pv210 and Exynos SOC's on-chip EHCI
303	  controller.
304
305config USB_EHCI_MV
306	tristate "EHCI support for Marvell PXA/MMP USB controller"
307	depends on ARCH_PXA || ARCH_MMP || COMPILE_TEST
308	select USB_EHCI_ROOT_HUB_TT
309	help
310	  Enables support for Marvell (including PXA and MMP series) on-chip
311	  USB SPH and OTG controller. SPH is a single port host, and it can
312	  only be EHCI host. OTG is controller that can switch to host mode.
313	  Note that this driver will not work on Marvell's other EHCI
314	  controller used by the EBU-type SoCs including Orion, Kirkwood,
315	  Dova, Armada 370 and Armada XP. See "Support for Marvell EBU
316	  on-chip EHCI USB controller" for those.
317
318config USB_OCTEON_HCD
319	tristate "Cavium Networks Octeon USB support"
320	depends on CAVIUM_OCTEON_SOC && USB
321	help
322	  This driver supports USB host controller on some Cavium
323	  Networks' products in the Octeon family.
324
325	  To compile this driver as a module, choose M here. The module
326	  will be called octeon-hcd.
327
328config USB_CNS3XXX_EHCI
329	bool "Cavium CNS3XXX EHCI Module (DEPRECATED)"
330	depends on ARCH_CNS3XXX || COMPILE_TEST
331	select USB_EHCI_HCD_PLATFORM
332	help
333	  This option is deprecated now and the driver was removed, use
334	  USB_EHCI_HCD_PLATFORM instead.
335
336	  Enable support for the CNS3XXX SOC's on-chip EHCI controller.
337	  It is needed for high-speed (480Mbit/sec) USB 2.0 device
338	  support.
339
340config USB_EHCI_HCD_PLATFORM
341	tristate "Generic EHCI driver for a platform device"
342	help
343	  Adds an EHCI host driver for a generic platform device, which
344	  provides a memory space and an irq.
345
346	  If unsure, say N.
347
348config USB_OCTEON_EHCI
349	bool "Octeon on-chip EHCI support (DEPRECATED)"
350	depends on CAVIUM_OCTEON_SOC
351	select USB_EHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
352	select USB_EHCI_HCD_PLATFORM
353	help
354	  This option is deprecated now and the driver was removed, use
355	  USB_EHCI_HCD_PLATFORM instead.
356
357	  Enable support for the Octeon II SOC's on-chip EHCI
358	  controller.  It is needed for high-speed (480Mbit/sec)
359	  USB 2.0 device support.  All CN6XXX based chips with USB are
360	  supported.
361
362endif # USB_EHCI_HCD
363
364config USB_OXU210HP_HCD
365	tristate "OXU210HP HCD support"
366	depends on HAS_IOMEM
367	help
368	  The OXU210HP is an USB host/OTG/device controller. Enable this
369	  option if your board has this chip. If unsure, say N.
370
371	  This driver does not support isochronous transfers and doesn't
372	  implement OTG nor USB device controllers.
373
374	  To compile this driver as a module, choose M here: the
375	  module will be called oxu210hp-hcd.
376
377config USB_ISP116X_HCD
378	tristate "ISP116X HCD support"
379	depends on HAS_IOMEM
380	help
381	  The ISP1160 and ISP1161 chips are USB host controllers. Enable this
382	  option if your board has this chip. If unsure, say N.
383
384	  This driver does not support isochronous transfers.
385
386	  To compile this driver as a module, choose M here: the
387	  module will be called isp116x-hcd.
388
389config USB_ISP1362_HCD
390	tristate "ISP1362 HCD support"
391	depends on HAS_IOMEM
392	depends on COMPILE_TEST # nothing uses this
393	help
394	  Supports the Philips ISP1362 chip as a host controller
395
396	  This driver does not support isochronous transfers.
397
398	  To compile this driver as a module, choose M here: the
399	  module will be called isp1362-hcd.
400
401config USB_MAX3421_HCD
402	tristate "MAX3421 HCD (USB-over-SPI) support"
403	depends on USB && SPI
404	help
405	  The Maxim MAX3421E chip supports standard USB 2.0-compliant
406	  full-speed devices either in host or peripheral mode.  This
407	  driver supports the host-mode of the MAX3421E only.
408
409	  To compile this driver as a module, choose M here: the module will
410	  be called max3421-hcd.
411
412config USB_OHCI_HCD
413	tristate "OHCI HCD (USB 1.1) support"
414	depends on HAS_DMA && HAS_IOMEM
415	help
416	  The Open Host Controller Interface (OHCI) is a standard for accessing
417	  USB 1.1 host controller hardware.  It does more in hardware than Intel's
418	  UHCI specification.  If your USB host controller follows the OHCI spec,
419	  say Y.  On most non-x86 systems, and on x86 hardware that's not using a
420	  USB controller from Intel or VIA, this is appropriate.  If your host
421	  controller doesn't use PCI, this is probably appropriate.  For a PCI
422	  based system where you're not sure, the "lspci -v" entry will list the
423	  right "prog-if" for your USB controller(s):  EHCI, OHCI, or UHCI.
424
425	  To compile this driver as a module, choose M here: the
426	  module will be called ohci-hcd.
427
428if USB_OHCI_HCD
429
430config USB_OHCI_HCD_OMAP1
431	tristate "OHCI support for OMAP1/2 chips"
432	depends on ARCH_OMAP1
433	depends on ISP1301_OMAP || !(MACH_OMAP_H2 || MACH_OMAP_H3)
434	default y
435	help
436	  Enables support for the OHCI controller on OMAP1/2 chips.
437
438config USB_OHCI_HCD_SPEAR
439	tristate "Support for ST SPEAr on-chip OHCI USB controller"
440	depends on USB_OHCI_HCD && (PLAT_SPEAR || COMPILE_TEST)
441	default y if PLAT_SPEAR
442	help
443	  Enables support for the on-chip OHCI controller on
444	  ST SPEAr chips.
445
446config USB_OHCI_HCD_STI
447	tristate "Support for ST STiHxxx on-chip OHCI USB controller"
448	depends on (ARCH_STI || COMPILE_TEST) && OF
449	select GENERIC_PHY
450	select USB_OHCI_HCD_PLATFORM
451	help
452	  Enable support for the on-chip OHCI controller found on
453	  STMicroelectronics consumer electronics SoC's.
454
455config USB_OHCI_HCD_S3C2410
456	tristate "OHCI support for Samsung S3C24xx/S3C64xx SoC series"
457	depends on USB_OHCI_HCD && (ARCH_S3C24XX || ARCH_S3C64XX || COMPILE_TEST)
458	default y if (ARCH_S3C24XX || ARCH_S3C64XX)
459	help
460	  Enables support for the on-chip OHCI controller on
461	  S3C24xx/S3C64xx chips.
462
463config USB_OHCI_HCD_LPC32XX
464	tristate "Support for LPC on-chip OHCI USB controller"
465	depends on USB_OHCI_HCD
466	depends on ARCH_LPC32XX || COMPILE_TEST
467	depends on USB_ISP1301
468	default y
469	help
470	  Enables support for the on-chip OHCI controller on
471	  NXP chips.
472
473config USB_OHCI_HCD_PXA27X
474	tristate "Support for PXA27X/PXA3XX on-chip OHCI USB controller"
475	depends on USB_OHCI_HCD && (PXA27x || PXA3xx)
476	default y
477	help
478	  Enables support for the on-chip OHCI controller on
479	  PXA27x/PXA3xx chips.
480
481config USB_OHCI_HCD_AT91
482	tristate "Support for Atmel on-chip OHCI USB controller"
483	depends on USB_OHCI_HCD && (ARCH_AT91 || COMPILE_TEST) && OF
484	default y if ARCH_AT91
485	help
486	  Enables support for the on-chip OHCI controller on
487	  Atmel chips.
488
489config USB_OHCI_HCD_OMAP3
490	tristate "OHCI support for OMAP3 and later chips"
491	depends on ARCH_OMAP3 || ARCH_OMAP4 || SOC_OMAP5 || COMPILE_TEST
492	select USB_OHCI_HCD_PLATFORM
493	default y if ARCH_OMAP3 || ARCH_OMAP4 || SOC_OMAP5
494	help
495	  This option is deprecated now and the driver was removed, use
496	  USB_OHCI_HCD_PLATFORM instead.
497
498	  Enables support for the on-chip OHCI controller on
499	  OMAP3 and later chips.
500
501config USB_OHCI_HCD_DAVINCI
502	tristate "OHCI support for TI DaVinci DA8xx"
503	depends on ARCH_DAVINCI_DA8XX || COMPILE_TEST
504	depends on USB_OHCI_HCD
505	select PHY_DA8XX_USB
506	default y if ARCH_DAVINCI_DA8XX
507	help
508	  Enables support for the DaVinci DA8xx integrated OHCI
509	  controller. This driver cannot currently be a loadable
510	  module because it lacks a proper PHY abstraction.
511
512config USB_OHCI_HCD_PPC_OF_BE
513	bool "OHCI support for OF platform bus (big endian)"
514	depends on PPC
515	select USB_OHCI_BIG_ENDIAN_DESC
516	select USB_OHCI_BIG_ENDIAN_MMIO
517	help
518	  Enables support for big-endian USB controllers present on the
519	  OpenFirmware platform bus.
520
521config USB_OHCI_HCD_PPC_OF_LE
522	bool "OHCI support for OF platform bus (little endian)"
523	depends on PPC
524	select USB_OHCI_LITTLE_ENDIAN
525	help
526	  Enables support for little-endian USB controllers present on the
527	  OpenFirmware platform bus.
528
529config USB_OHCI_HCD_PPC_OF
530	bool
531	depends on PPC
532	default USB_OHCI_HCD_PPC_OF_BE || USB_OHCI_HCD_PPC_OF_LE
533
534config USB_OHCI_HCD_PCI
535	tristate "OHCI support for PCI-bus USB controllers"
536	depends on USB_PCI
537	default y
538	select USB_OHCI_LITTLE_ENDIAN
539	help
540	  Enables support for PCI-bus plug-in USB controller cards.
541	  If unsure, say Y.
542
543config USB_OHCI_HCD_SSB
544	bool "OHCI support for Broadcom SSB OHCI core (DEPRECATED)"
545	depends on (SSB = y || SSB = USB_OHCI_HCD)
546	select USB_HCD_SSB
547	select USB_OHCI_HCD_PLATFORM
548	help
549	  This option is deprecated now and the driver was removed, use
550	  USB_HCD_SSB and USB_OHCI_HCD_PLATFORM instead.
551
552	  Support for the Sonics Silicon Backplane (SSB) attached
553	  Broadcom USB OHCI core.
554
555	  This device is present in some embedded devices with
556	  Broadcom based SSB bus.
557
558	  If unsure, say N.
559
560config USB_OHCI_EXYNOS
561	tristate "OHCI support for Samsung S5P/Exynos SoC Series"
562	depends on ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST
563	help
564	  Enable support for the Samsung S5Pv210 and Exynos SOC's on-chip OHCI
565	  controller.
566
567config USB_CNS3XXX_OHCI
568	bool "Cavium CNS3XXX OHCI Module (DEPRECATED)"
569	depends on ARCH_CNS3XXX || COMPILE_TEST
570	select USB_OHCI_HCD_PLATFORM
571	help
572	  This option is deprecated now and the driver was removed, use
573	  USB_OHCI_HCD_PLATFORM instead.
574
575	  Enable support for the CNS3XXX SOC's on-chip OHCI controller.
576	  It is needed for low-speed USB 1.0 device support.
577
578config USB_OHCI_HCD_PLATFORM
579	tristate "Generic OHCI driver for a platform device"
580	help
581	  Adds an OHCI host driver for a generic platform device, which
582	  provides a memory space and an irq.
583
584	  If unsure, say N.
585
586config USB_OCTEON_OHCI
587	bool "Octeon on-chip OHCI support (DEPRECATED)"
588	depends on CAVIUM_OCTEON_SOC
589	default USB_OCTEON_EHCI
590	select USB_OHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
591	select USB_OHCI_LITTLE_ENDIAN
592	select USB_OHCI_HCD_PLATFORM
593	help
594	  This option is deprecated now and the driver was removed, use
595	  USB_OHCI_HCD_PLATFORM instead.
596
597	  Enable support for the Octeon II SOC's on-chip OHCI
598	  controller.  It is needed for low-speed USB 1.0 device
599	  support.  All CN6XXX based chips with USB are supported.
600
601endif # USB_OHCI_HCD
602
603config USB_UHCI_HCD
604	tristate "UHCI HCD (most Intel and VIA) support"
605	depends on USB_PCI || USB_UHCI_SUPPORT_NON_PCI_HC
606	help
607	  The Universal Host Controller Interface is a standard by Intel for
608	  accessing the USB hardware in the PC (which is also called the USB
609	  host controller). If your USB host controller conforms to this
610	  standard, you may want to say Y, but see below. All recent boards
611	  with Intel PCI chipsets (like intel 430TX, 440FX, 440LX, 440BX,
612	  i810, i820) conform to this standard. Also all VIA PCI chipsets
613	  (like VIA VP2, VP3, MVP3, Apollo Pro, Apollo Pro II or Apollo Pro
614	  133) and LEON/GRLIB SoCs with the GRUSBHC controller.
615	  If unsure, say Y.
616
617	  To compile this driver as a module, choose M here: the
618	  module will be called uhci-hcd.
619
620config USB_UHCI_SUPPORT_NON_PCI_HC
621	bool
622	default y if (SPARC_LEON || USB_UHCI_PLATFORM)
623
624config USB_UHCI_PLATFORM
625	bool
626	default y if (ARCH_VT8500 || ARCH_ASPEED)
627
628config USB_UHCI_ASPEED
629	bool
630	default y if ARCH_ASPEED
631
632config USB_FHCI_HCD
633	tristate "Freescale QE USB Host Controller support"
634	depends on OF_GPIO && QE_GPIO && QUICC_ENGINE
635	select FSL_GTM
636	select QE_USB
637	help
638	  This driver enables support for Freescale QE USB Host Controller
639	  (as found on MPC8360 and MPC8323 processors), the driver supports
640	  Full and Low Speed USB.
641
642config FHCI_DEBUG
643	bool "Freescale QE USB Host Controller debug support"
644	depends on USB_FHCI_HCD && DEBUG_FS
645	help
646	  Say "y" to see some FHCI debug information and statistics
647	  through debugfs.
648
649config USB_U132_HCD
650	tristate "Elan U132 Adapter Host Controller"
651	depends on USB_FTDI_ELAN
652	help
653	  The U132 adapter is a USB to CardBus adapter specifically designed
654	  for PC cards that contain an OHCI host controller. Typical PC cards
655	  are the Orange Mobile 3G Option GlobeTrotter Fusion card. The U132
656	  adapter will *NOT* work with PC cards that do not contain an OHCI
657	  controller.
658
659	  For those PC cards that contain multiple OHCI controllers only the
660	  first one is used.
661
662	  The driver consists of two modules, the "ftdi-elan" module is a
663	  USB client driver that interfaces to the FTDI chip within ELAN's
664	  USB-to-PCMCIA adapter, and this "u132-hcd" module is a USB host
665	  controller driver that talks to the OHCI controller within the
666	  CardBus cards that are inserted in the U132 adapter.
667
668	  This driver has been tested with a CardBus OHCI USB adapter, and
669	  worked with a USB PEN Drive inserted into the first USB port of
670	  the PCCARD. A rather pointless thing to do, but useful for testing.
671
672	  It is safe to say M here.
673
674	  See also <http://www.elandigitalsystems.com/support/ufaq/u132linux.php>
675
676config USB_SL811_HCD
677	tristate "SL811HS HCD support"
678	depends on HAS_IOMEM
679	help
680	  The SL811HS is a single-port USB controller that supports either
681	  host side or peripheral side roles.  Enable this option if your
682	  board has this chip, and you want to use it as a host controller.
683	  If unsure, say N.
684
685	  To compile this driver as a module, choose M here: the
686	  module will be called sl811-hcd.
687
688config USB_SL811_HCD_ISO
689	bool "partial ISO support"
690	depends on USB_SL811_HCD
691	help
692	  The driver doesn't support iso_frame_desc (yet), but for some simple
693	  devices that just queue one ISO frame per URB, then ISO transfers
694	  "should" work using the normal urb status fields.
695
696	  If unsure, say N.
697
698config USB_SL811_CS
699	tristate "CF/PCMCIA support for SL811HS HCD"
700	depends on USB_SL811_HCD && PCMCIA
701	help
702	  Wraps a PCMCIA driver around the SL811HS HCD, supporting the RATOC
703	  REX-CFU1U CF card (often used with PDAs).  If unsure, say N.
704
705	  To compile this driver as a module, choose M here: the
706	  module will be called "sl811_cs".
707
708config USB_R8A66597_HCD
709	tristate "R8A66597 HCD support"
710	depends on HAS_IOMEM
711	help
712	  The R8A66597 is a USB 2.0 host and peripheral controller.
713
714	  Enable this option if your board has this chip, and you want
715	  to use it as a host controller.  If unsure, say N.
716
717	  To compile this driver as a module, choose M here: the
718	  module will be called r8a66597-hcd.
719
720config USB_RENESAS_USBHS_HCD
721	tristate "Renesas USBHS HCD support"
722	depends on USB_RENESAS_USBHS
723	help
724	  The Renesas USBHS is a USB 2.0 host and peripheral controller.
725
726	  Enable this option if your board has this chip, and you want
727	  to use it as a host controller.  If unsure, say N.
728
729	  To compile this driver as a module, choose M here: the
730	  module will be called renesas-usbhs.
731
732config USB_HCD_BCMA
733	tristate "BCMA usb host driver"
734	depends on BCMA
735	select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD
736	select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD
737	help
738	  Enable support for the EHCI and OCHI host controller on an bcma bus.
739	  It converts the bcma driver into two platform device drivers
740	  for ehci and ohci.
741
742	  If unsure, say N.
743
744config USB_HCD_SSB
745	tristate "SSB usb host driver"
746	depends on SSB
747	select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD
748	select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD
749	help
750	  Enable support for the EHCI and OCHI host controller on an bcma bus.
751	  It converts the bcma driver into two platform device drivers
752	  for ehci and ohci.
753
754	  If unsure, say N.
755
756config USB_HCD_TEST_MODE
757	bool "HCD test mode support"
758	help
759	  Say 'Y' to enable additional software test modes that may be
760	  supported by the host controller drivers.
761
762	  One such test mode is the Embedded High-speed Host Electrical Test
763	  (EHSET) for EHCI host controller hardware, specifically the "Single
764	  Step Set Feature" test.  Typically this will be enabled for On-the-Go
765	  or embedded hosts that need to undergo USB-IF compliance testing with
766	  the aid of special testing hardware.  In the future, this may expand
767	  to include other tests that require support from a HCD driver.
768
769	  This option is of interest only to developers who need to validate
770	  their USB hardware designs.  It is not needed for normal use.  If
771	  unsure, say N.
772
773config USB_XEN_HCD
774	tristate "Xen usb virtual host driver"
775	depends on XEN
776	select XEN_XENBUS_FRONTEND
777	help
778	  The Xen usb virtual host driver serves as a frontend driver enabling
779	  a Xen guest system to access USB Devices passed through to the guest
780	  by the Xen host (usually Dom0).
781	  Only needed if the kernel is running in a Xen guest and generic
782	  access to a USB device is needed.
783