1# SPDX-License-Identifier: GPL-2.0-only 2# 3# wan devices configuration 4# 5 6menuconfig WAN 7 bool "Wan interfaces support" 8 help 9 Wide Area Networks (WANs), such as X.25, Frame Relay and leased 10 lines, are used to interconnect Local Area Networks (LANs) over vast 11 distances with data transfer rates significantly higher than those 12 achievable with commonly used asynchronous modem connections. 13 14 Usually, a quite expensive external device called a `WAN router' is 15 needed to connect to a WAN. As an alternative, a relatively 16 inexpensive WAN interface card can allow your Linux box to directly 17 connect to a WAN. 18 19 If you have one of those cards and wish to use it under Linux, 20 say Y here and also to the WAN driver for your card. 21 22 If unsure, say N. 23 24if WAN 25 26# There is no way to detect a comtrol sv11 - force it modular for now. 27config HOSTESS_SV11 28 tristate "Comtrol Hostess SV-11 support" 29 depends on ISA && m && ISA_DMA_API && INET && HDLC && VIRT_TO_BUS 30 help 31 Driver for Comtrol Hostess SV-11 network card which 32 operates on low speed synchronous serial links at up to 33 256Kbps, supporting PPP and Cisco HDLC. 34 35 The driver will be compiled as a module: the 36 module will be called hostess_sv11. 37 38# There is no way to detect a Sealevel board. Force it modular 39config SEALEVEL_4021 40 tristate "Sealevel Systems 4021 support" 41 depends on ISA && m && ISA_DMA_API && INET && HDLC && VIRT_TO_BUS 42 help 43 This is a driver for the Sealevel Systems ACB 56 serial I/O adapter. 44 45 The driver will be compiled as a module: the 46 module will be called sealevel. 47 48# Generic HDLC 49config HDLC 50 tristate "Generic HDLC layer" 51 help 52 Say Y to this option if your Linux box contains a WAN (Wide Area 53 Network) card supported by this driver and you are planning to 54 connect the box to a WAN. 55 56 You will need supporting software from 57 <http://www.kernel.org/pub/linux/utils/net/hdlc/>. 58 Generic HDLC driver currently supports raw HDLC, Cisco HDLC, Frame 59 Relay, synchronous Point-to-Point Protocol (PPP) and X.25. 60 61 To compile this driver as a module, choose M here: the 62 module will be called hdlc. 63 64 If unsure, say N. 65 66config HDLC_RAW 67 tristate "Raw HDLC support" 68 depends on HDLC 69 help 70 Generic HDLC driver supporting raw HDLC over WAN connections. 71 72 If unsure, say N. 73 74config HDLC_RAW_ETH 75 tristate "Raw HDLC Ethernet device support" 76 depends on HDLC 77 help 78 Generic HDLC driver supporting raw HDLC Ethernet device emulation 79 over WAN connections. 80 81 You will need it for Ethernet over HDLC bridges. 82 83 If unsure, say N. 84 85config HDLC_CISCO 86 tristate "Cisco HDLC support" 87 depends on HDLC 88 help 89 Generic HDLC driver supporting Cisco HDLC over WAN connections. 90 91 If unsure, say N. 92 93config HDLC_FR 94 tristate "Frame Relay support" 95 depends on HDLC 96 help 97 Generic HDLC driver supporting Frame Relay over WAN connections. 98 99 If unsure, say N. 100 101config HDLC_PPP 102 tristate "Synchronous Point-to-Point Protocol (PPP) support" 103 depends on HDLC 104 help 105 Generic HDLC driver supporting PPP over WAN connections. 106 107 If unsure, say N. 108 109config HDLC_X25 110 tristate "X.25 protocol support" 111 depends on HDLC && (LAPB=m && HDLC=m || LAPB=y) 112 help 113 Generic HDLC driver supporting X.25 over WAN connections. 114 115 If unsure, say N. 116 117comment "X.25/LAPB support is disabled" 118 depends on HDLC && (LAPB!=m || HDLC!=m) && LAPB!=y 119 120config PCI200SYN 121 tristate "Goramo PCI200SYN support" 122 depends on HDLC && PCI 123 help 124 Driver for PCI200SYN cards by Goramo sp. j. 125 126 If you have such a card, say Y here and see 127 <http://www.kernel.org/pub/linux/utils/net/hdlc/>. 128 129 To compile this as a module, choose M here: the 130 module will be called pci200syn. 131 132 If unsure, say N. 133 134config WANXL 135 tristate "SBE Inc. wanXL support" 136 depends on HDLC && PCI 137 help 138 Driver for wanXL PCI cards by SBE Inc. 139 140 If you have such a card, say Y here and see 141 <http://www.kernel.org/pub/linux/utils/net/hdlc/>. 142 143 To compile this as a module, choose M here: the 144 module will be called wanxl. 145 146 If unsure, say N. 147 148config WANXL_BUILD_FIRMWARE 149 bool "rebuild wanXL firmware" 150 depends on WANXL && !PREVENT_FIRMWARE_BUILD 151 help 152 Allows you to rebuild firmware run by the QUICC processor. 153 It requires m68k toolchains and hexdump programs. 154 155 You should never need this option, say N. 156 157config PC300TOO 158 tristate "Cyclades PC300 RSV/X21 alternative support" 159 depends on HDLC && PCI 160 help 161 Alternative driver for PC300 RSV/X21 PCI cards made by 162 Cyclades, Inc. If you have such a card, say Y here and see 163 <http://www.kernel.org/pub/linux/utils/net/hdlc/>. 164 165 To compile this as a module, choose M here: the module 166 will be called pc300too. 167 168 If unsure, say N here. 169 170config N2 171 tristate "SDL RISCom/N2 support" 172 depends on HDLC && ISA 173 help 174 Driver for RISCom/N2 single or dual channel ISA cards by 175 SDL Communications Inc. 176 177 If you have such a card, say Y here and see 178 <http://www.kernel.org/pub/linux/utils/net/hdlc/>. 179 180 Note that N2csu and N2dds cards are not supported by this driver. 181 182 To compile this driver as a module, choose M here: the module 183 will be called n2. 184 185 If unsure, say N. 186 187config C101 188 tristate "Moxa C101 support" 189 depends on HDLC && ISA 190 help 191 Driver for C101 SuperSync ISA cards by Moxa Technologies Co., Ltd. 192 193 If you have such a card, say Y here and see 194 <http://www.kernel.org/pub/linux/utils/net/hdlc/>. 195 196 To compile this driver as a module, choose M here: the 197 module will be called c101. 198 199 If unsure, say N. 200 201config FARSYNC 202 tristate "FarSync T-Series support" 203 depends on HDLC && PCI 204 help 205 Support for the FarSync T-Series X.21 (and V.35/V.24) cards by 206 FarSite Communications Ltd. 207 208 Synchronous communication is supported on all ports at speeds up to 209 8Mb/s (128K on V.24) using synchronous PPP, Cisco HDLC, raw HDLC, 210 Frame Relay or X.25/LAPB. 211 212 If you want the module to be automatically loaded when the interface 213 is referenced then you should add "alias hdlcX farsync" to a file 214 in /etc/modprobe.d/ for each interface, where X is 0, 1, 2, ..., or 215 simply use "alias hdlc* farsync" to indicate all of them. 216 217 To compile this driver as a module, choose M here: the 218 module will be called farsync. 219 220config FSL_UCC_HDLC 221 tristate "Freescale QUICC Engine HDLC support" 222 depends on HDLC 223 depends on QUICC_ENGINE 224 help 225 Driver for Freescale QUICC Engine HDLC controller. The driver 226 supports HDLC in NMSI and TDM mode. 227 228 To compile this driver as a module, choose M here: the 229 module will be called fsl_ucc_hdlc. 230 231config SLIC_DS26522 232 tristate "Slic Maxim ds26522 card support" 233 depends on SPI 234 depends on FSL_SOC || ARCH_MXC || ARCH_LAYERSCAPE || COMPILE_TEST 235 select BITREVERSE 236 help 237 This module initializes and configures the slic maxim card 238 in T1 or E1 mode. 239 240 To compile this driver as a module, choose M here: the 241 module will be called slic_ds26522. 242 243config IXP4XX_HSS 244 tristate "Intel IXP4xx HSS (synchronous serial port) support" 245 depends on HDLC && IXP4XX_NPE && IXP4XX_QMGR 246 depends on ARCH_IXP4XX && OF 247 select MFD_SYSCON 248 help 249 Say Y here if you want to use built-in HSS ports 250 on IXP4xx processor. 251 252# X.25 network drivers 253config LAPBETHER 254 tristate "LAPB over Ethernet driver" 255 depends on LAPB && X25 256 help 257 Driver for a pseudo device (typically called /dev/lapb0) which allows 258 you to open an LAPB point-to-point connection to some other computer 259 on your Ethernet network. 260 261 In order to do this, you need to say Y or M to the driver for your 262 Ethernet card as well as to "LAPB Data Link Driver". 263 264 To compile this driver as a module, choose M here: the 265 module will be called lapbether. 266 267 268 If unsure, say N. 269 270endif # WAN 271