1a9643ea8Slogwang# 2a9643ea8Slogwang# DIR-655A1 - 3x3 2GHz D-Link AP 3a9643ea8Slogwang# 4a9643ea8Slogwang# This contains a QCA9558 MIPS74k SoC with on-board 3x3 2GHz wifi, 5a9643ea8Slogwang# 128MiB RAM, an AR8327 5-port gigabit ethernet switch. 6a9643ea8Slogwang# 7a9643ea8Slogwang# $FreeBSD$ 8a9643ea8Slogwang# 9a9643ea8Slogwang 10a9643ea8Slogwang#NO_UNIVERSE 11a9643ea8Slogwang 12a9643ea8Slogwang# Include the default QCA955x parameters 13*22ce4affSfengbojianginclude "std.QCA955X" 14a9643ea8Slogwang 15a9643ea8Slogwangident DIR-655A1 16a9643ea8Slogwang 17a9643ea8Slogwang# Override hints with board values 18a9643ea8Slogwanghints "DIR-655A1.hints" 19a9643ea8Slogwang 20a9643ea8Slogwang# Force the board memory - the base AP135 has 128MB RAM 21a9643ea8Slogwangoptions AR71XX_REALMEM=(128*1024*1024) 22a9643ea8Slogwang 23a9643ea8Slogwang# i2c GPIO bus 24a9643ea8Slogwang#device gpioiic 25a9643ea8Slogwang#device iicbb 26a9643ea8Slogwang#device iicbus 27a9643ea8Slogwang#device iic 28a9643ea8Slogwang 29a9643ea8Slogwang# Options required for miiproxy and mdiobus 30a9643ea8Slogwangoptions ARGE_MDIO # Export an MDIO bus separate from arge 31a9643ea8Slogwangdevice miiproxy # MDIO bus <-> MII PHY rendezvous 32a9643ea8Slogwang 33a9643ea8Slogwangdevice etherswitch 34a9643ea8Slogwangdevice arswitch 35a9643ea8Slogwang 36a9643ea8Slogwang# read MSDOS formatted disks - USB 37a9643ea8Slogwang#options MSDOSFS 38a9643ea8Slogwang 39a9643ea8Slogwang# Enable the uboot environment stuff rather then the 40a9643ea8Slogwang# redboot stuff. 41a9643ea8Slogwangoptions AR71XX_ENV_UBOOT 42a9643ea8Slogwang 43a9643ea8Slogwang# uzip - to boot natively from flash 44*22ce4affSfengbojiangdevice xz 45a9643ea8Slogwangoptions GEOM_UZIP 46a9643ea8Slogwang 47a9643ea8Slogwang# Used for the static uboot partition map 48a9643ea8Slogwangdevice geom_map 49a9643ea8Slogwang 50a9643ea8Slogwangoptions AR71XX_ATH_EEPROM 51a9643ea8Slogwangdevice firmware # Used by the above 52a9643ea8Slogwangoptions ATH_EEPROM_FIRMWARE 53a9643ea8Slogwang 54a9643ea8Slogwang# Boot off of the rootfs, as defined in the geom_map setup. 55a9643ea8Slogwangoptions ROOTDEVNAME=\"ufs:map/rootfs.uzip\" 56a9643ea8Slogwang 57a9643ea8Slogwang# Default to accept 58a9643ea8Slogwangoptions IPFIREWALL_DEFAULT_TO_ACCEPT 59