1[dpdk] 2# Hexadecimal bitmask of cores to run on. 3lcore_mask=1 4 5# Number of memory channels. 6channel=4 7 8# Specify base virtual address to map. 9#base_virtaddr=0x7f0000000000 10 11# Promiscuous mode of nic, defualt: enabled. 12promiscuous=1 13numa_on=1 14 15# TX checksum offload skip, default: disabled. 16# We need this switch enabled in the following cases: 17# -> The application want to enforce wrong checksum for testing purposes 18# -> Some cards advertize the offload capability. However, doesn't calculate checksum. 19tx_csum_offoad_skip=0 20 21# TCP segment offload, default: disabled. 22tso=0 23 24# HW vlan strip, default: enabled. 25vlan_strip=1 26 27# sleep when no pkts incomming 28# unit: microseconds 29idle_sleep=0 30 31# sent packet delay time(0-100) while send less than 32 pkts. 32# default 100 us. 33# if set 0, means send pkts immediately. 34# if set >100, will dealy 100 us. 35# unit: microseconds 36pkt_tx_delay=100 37 38# use symmetric Receive-side Scaling(RSS) key, default: disabled. 39symmetric_rss=0 40 41# PCI device enable list. 42# And driver options 43#pci_whitelist=02:00.0 44# for multiple PCI devices 45#pci_whilelist=02:00.0,03:00.0 46 47# enabled port list 48# 49# EBNF grammar: 50# 51# exp ::= num_list {"," num_list} 52# num_list ::= <num> | <range> 53# range ::= <num>"-"<num> 54# num ::= '0' | '1' | '2' | '3' | '4' | '5' | '6' | '7' | '8' | '9' 55# 56# examples 57# 0-3 ports 0, 1,2,3 are enabled 58# 1-3,4,7 ports 1,2,3,4,7 are enabled 59# 60# If use bonding, shoule config the bonding port id in port_list 61# and not config slave port id in port_list 62# such as, port 0 and port 1 trank to a bonding port 2, 63# should set `port_list=2` and config `[port2]` section 64 65port_list=0 66 67# Number of vdev. 68nb_vdev=0 69 70# Number of bond. 71nb_bond=0 72 73# Each core write into own pcap file, which is open one time, close one time if enough. 74# Support dump the first snaplen bytes of each packet. 75# if pcap file is lager than savelen bytes, it will be closed and next file was dumped into. 76[pcap] 77enable=0 78snaplen=96 79savelen=16777216 80savepath=. 81 82# Port config section 83# Correspond to dpdk.port_list's index: port0, port1... 84[port0] 85addr=192.168.1.2 86netmask=255.255.225.0 87broadcast=192.168.1.255 88gateway=192.168.1.1 89 90# IPv6 net addr, Optional parameters. 91#addr6=ff::02 92#prefix_len=64 93#gateway6=ff::01 94 95# Multi virtual IPv4/IPv6 net addr, Optional parameters. 96# `vip_ifname`: default `f-stack-x` 97# `vip_addr`: Separated by semicolons, MAX number 64; 98# Only support netmask 255.255.255.255, broadcast x.x.x.255 now, hard code in `ff_veth_setvaddr`. 99# `vip_addr6`: Separated by semicolons, MAX number 64. 100# `vip_prefix_len`: All addr6 use the same prefix now, default 64. 101#vip_ifname=lo0 102#vip_addr=192.168.1.3;192.168.1.4;192.168.1.5;192.168.1.6 103#vip_addr6=ff::03;ff::04;ff::05;ff::06;ff::07 104#vip_prefix_len=64 105 106# lcore list used to handle this port 107# the format is same as port_list 108#lcore_list=0 109 110# bonding slave port list used to handle this port 111# need to config while this port is a bonding port 112# the format is same as port_list 113#slave_port_list=0,1 114 115# Vdev config section 116# orrespond to dpdk.nb_vdev's index: vdev0, vdev1... 117# iface : Shouldn't set always. 118# path : The vuser device path in container. Required. 119# queues : The max queues of vuser. Optional, default 1, greater or equal to the number of processes. 120# queue_size : Queue size.Optional, default 256. 121# mac : The mac address of vuser. Optional, default random, if vhost use phy NIC, it should be set to the phy NIC's mac. 122# cq : Optional, if queues = 1, default 0; if queues > 1 default 1. 123#[vdev0] 124##iface=/usr/local/var/run/openvswitch/vhost-user0 125#path=/var/run/openvswitch/vhost-user0 126#queues=1 127#queue_size=256 128#mac=00:00:00:00:00:01 129#cq=0 130 131# bond config section 132# See http://doc.dpdk.org/guides/prog_guide/link_bonding_poll_mode_drv_lib.html 133#[bond0] 134#mode=4 135#slave=0000:0a:00.0,slave=0000:0a:00.1 136#primary=0000:0a:00.0 137#mac=f0:98:38:xx:xx:xx 138## opt argument 139#socket_id=0 140#xmit_policy=l23 141#lsc_poll_period_ms=100 142#up_delay=10 143#down_delay=50 144 145# Kni config: if enabled and method=reject, 146# all packets that do not belong to the following tcp_port and udp_port 147# will transmit to kernel; if method=accept, all packets that belong to 148# the following tcp_port and udp_port will transmit to kernel. 149#[kni] 150#enable=1 151#method=reject 152# The format is same as port_list 153#tcp_port=80,443 154#udp_port=53 155 156# FreeBSD network performance tuning configurations. 157# Most native FreeBSD configurations are supported. 158[freebsd.boot] 159hz=100 160 161# Block out a range of descriptors to avoid overlap 162# with the kernel's descriptor space. 163# You can increase this value according to your app. 164fd_reserve=1024 165 166kern.ipc.maxsockets=262144 167 168net.inet.tcp.syncache.hashsize=4096 169net.inet.tcp.syncache.bucketlimit=100 170 171net.inet.tcp.tcbhashsize=65536 172 173kern.ncallout=262144 174 175kern.features.inet6=1 176net.inet6.ip6.auto_linklocal=1 177net.inet6.ip6.accept_rtadv=2 178net.inet6.icmp6.rediraccept=1 179net.inet6.ip6.forwarding=0 180 181[freebsd.sysctl] 182kern.ipc.somaxconn=32768 183kern.ipc.maxsockbuf=16777216 184 185net.link.ether.inet.maxhold=5 186 187net.inet.tcp.fast_finwait2_recycle=1 188net.inet.tcp.sendspace=16384 189net.inet.tcp.recvspace=8192 190#net.inet.tcp.nolocaltimewait=1 191net.inet.tcp.cc.algorithm=cubic 192net.inet.tcp.sendbuf_max=16777216 193net.inet.tcp.recvbuf_max=16777216 194net.inet.tcp.sendbuf_auto=1 195net.inet.tcp.recvbuf_auto=1 196net.inet.tcp.sendbuf_inc=16384 197#net.inet.tcp.recvbuf_inc=524288 198net.inet.tcp.sack.enable=1 199net.inet.tcp.blackhole=1 200net.inet.tcp.msl=2000 201net.inet.tcp.delayed_ack=0 202 203net.inet.udp.blackhole=1 204net.inet.ip.redirect=0 205net.inet.ip.forwarding=0 206 207#set default stacks:freebsd, rack or bbr 208net.inet.tcp.functions_default=freebsd 209