Home
last modified time | relevance | path

Searched refs:pulled (Results 1 – 25 of 82) sorted by relevance

1234

/linux-6.15/Documentation/devicetree/bindings/iio/pressure/
H A Dhoperf,hp03.yaml24 The XCLR pin is a reset of the ADC in the chip, it must be pulled
26 registers and pulled LO afterward.
/linux-6.15/arch/arm64/boot/dts/freescale/
H A Dimx8mm-venice-gw72xx-0x-rs485.dtso10 * - RS485_EN needs to be pulled high
11 * - RS485_HALF needs to be pulled high
H A Dimx8mm-venice-gw73xx-0x-rs485.dtso10 * - RS485_EN needs to be pulled high
11 * - RS485_HALF needs to be pulled high
H A Dimx8mm-venice-gw73xx-0x-rs422.dtso10 * - RS485_EN needs to be pulled high
H A Dimx8mm-venice-gw72xx-0x-rs422.dtso10 * - RS485_EN needs to be pulled high
/linux-6.15/drivers/net/ethernet/intel/fm10k/
H A Dfm10k_mbx.c349 end = fm10k_fifo_head_offset(fifo, mbx->pulled); in fm10k_mbx_write_copy()
389 mbx->pulled += mbx->tail_len - ack; in fm10k_mbx_pull_head()
393 len = fm10k_fifo_used(fifo) - mbx->pulled; in fm10k_mbx_pull_head()
403 len && (mbx->pulled >= len); in fm10k_mbx_pull_head()
405 mbx->pulled -= fm10k_fifo_head_drop(fifo); in fm10k_mbx_pull_head()
622 head = fm10k_fifo_head_offset(&mbx->tx, mbx->pulled); in fm10k_mbx_update_local_crc()
1068 mbx->pulled += mbx->tail_len - ack; in fm10k_mbx_reset_work()
1074 if (mbx->pulled >= len) in fm10k_mbx_reset_work()
1075 mbx->pulled -= len; in fm10k_mbx_reset_work()
1077 mbx->pulled = 0; in fm10k_mbx_reset_work()
[all …]
H A Dfm10k_mbx.h266 u16 tail, tail_len, pulled; member
/linux-6.15/Documentation/devicetree/bindings/sound/
H A Deverest,es7241.yaml33 the sdout. If the sdout is pulled down, leftj format is used.
34 If this property is not provided, sdout is assumed to pulled
/linux-6.15/Documentation/devicetree/bindings/iio/light/
H A Dvishay,veml6030.yaml63 - 0x10 # ADDR pin pulled down
64 - 0x48 # ADDR pin pulled up
/linux-6.15/Documentation/devicetree/bindings/gpio/
H A Dgpio-max3191x.txt31 pulled high (8-bit mode). Use this if the modesel pin
35 that modesel is pulled low (16-bit mode).
H A Dnxp,pcf8575.yaml60 the input (pulled-up) state.
85 Performing a reset makes all lines initialized to their input (pulled-up)
/linux-6.15/arch/powerpc/boot/dts/fsl/
H A Dp1023rdb.dts186 /* IRQ[0:3] are pulled up on board, set to active-low */
212 * IRQ[7] is pulled up on board, set to active-low
238 * IRQ[8:10] are pulled up on board, set to active-low
/linux-6.15/Documentation/dev-tools/
H A Dindex.rst6 be used to work on the kernel. For now, the documents have been pulled
/linux-6.15/Documentation/devicetree/bindings/iio/dac/
H A Dti,dac7612.yaml29 DACs are loaded when the pin connected to this GPIO is pulled low.
/linux-6.15/Documentation/devicetree/bindings/extcon/
H A Dqcom,pm8941-misc.yaml14 the USB ID pin has been pulled low or high.
/linux-6.15/Documentation/devicetree/bindings/mfd/
H A Dsamsung,s2mps11.yaml50 power. Usually the ACOKB is pulled up to VBATT so when PWRHOLD pin goes
56 Indicates that WRSTBI pin of PMIC is pulled down. When the system is
/linux-6.15/Documentation/devicetree/bindings/usb/
H A Dsamsung,exynos-usb2.yaml44 needs to be pulled up for the bus to be powered.
/linux-6.15/Documentation/devicetree/bindings/leds/
H A Dkinetic,ktd2692.yaml20 Also, When the AUX pin is pulled high while CTRL pin is high,
/linux-6.15/arch/arm/boot/dts/intel/pxa/
H A Dpxa3xx.dtsi88 * the configured driven and pulled levels match, so if there is a need for
89 * non-LPM pulled output, the same configuration could probably be used.
/linux-6.15/arch/arm/boot/dts/allwinner/
H A Dsunxi-d1s-t113-mangopi-mq-r.dtsi117 /* The USB-C socket has its CC pins pulled to GND, so is hardwired as a UFP. */
/linux-6.15/tools/power/pm-graph/config/
H A Dcustom-timeline-functions.cfg78 # The args are pulled directly from the stack using this architecture's registers
143 # The args are pulled directly from the stack using this architecture's registers
/linux-6.15/arch/arm64/boot/dts/allwinner/
H A Dsun50i-h618-longanpi-3h.dts128 * is not implemented: both CC pins are pulled to GND.
H A Dsun50i-h616-orangepi-zero.dtsi121 * is not implemented: both CC pins are pulled to GND.
/linux-6.15/Documentation/fb/
H A Dmetronomefb.rst17 The display and error status are each pulled through individual GPIOs.
/linux-6.15/Documentation/devicetree/bindings/iio/adc/
H A Dadi,ad7779.yaml64 correct operation. If an error is detected, the ALERT pin is pulled

1234