| /linux-6.15/drivers/rtc/ |
| H A D | rtc-ds1343.c | 147 char *diodes = "disabled", *resistors = " "; in ds1343_show_tricklecharger() local
166 resistors = "1k Ohm"; in ds1343_show_tricklecharger()
170 resistors = "2k Ohm"; in ds1343_show_tricklecharger()
174 resistors = "4k Ohm"; in ds1343_show_tricklecharger()
183 return sprintf(buf, "%s %s\n", diodes, resistors); in ds1343_show_tricklecharger()
|
| H A D | rtc-ds1305.c | 386 char *resistors = ""; in ds1305_proc() local
402 resistors = "2k Ohm"; in ds1305_proc()
405 resistors = "4k Ohm"; in ds1305_proc()
408 resistors = "8k Ohm"; in ds1305_proc()
417 seq_printf(seq, "trickle_charge\t: %s%s\n", diodes, resistors); in ds1305_proc()
|
| /linux-6.15/Documentation/devicetree/bindings/usb/ |
| H A D | ti,tusb73x0-pci.yaml | 28 PWRONx# pins are active high and their internal pull-down resistors are
30 and their internal pull-down resistors are enabled.
|
| /linux-6.15/Documentation/devicetree/bindings/mfd/ |
| H A D | adi,adp5585.yaml | 22 - adi,adp5585-02 # No pull-up resistors by default on special pins
24 - adi,adp5585-04 # Pull-down resistors on all pins by default
|
| /linux-6.15/drivers/gpu/drm/nouveau/nvkm/subdev/bios/ |
| H A D | iccsense.c | 122 rail->resistors[r].mohm = nvbios_rd08(bios, entry + res_start + r * 2); in nvbios_iccsense_parse()
123 rail->resistors[r].enabled = !(nvbios_rd08(bios, entry + res_start + r * 2 + 1) & 0x40); in nvbios_iccsense_parse()
|
| /linux-6.15/Documentation/devicetree/bindings/leds/ |
| H A D | richtek,rt8515.yaml | 15 current for each mode is defined in hardware using two resistors
34 resistors limits the maximum flash current. This must be set
43 resistors limits the maximum torch current. This must be set
|
| /linux-6.15/drivers/gpu/drm/nouveau/include/nvkm/subdev/bios/ |
| H A D | iccsense.h | 13 struct pwr_rail_resistor_t resistors[3]; member
|
| /linux-6.15/Documentation/hwmon/ |
| H A D | ina3221.rst | 48 value for their shunt resistors)
53 value for their shunt resistors)
|
| H A D | ltc2991.rst | 30 resistors or temperature sensing transistors. Additional measurements include
|
| H A D | ltc4260.rst | 44 registers. If a set of voltage divider resistors is installed, calculate the
|
| H A D | w83l785ts.rst | 25 of external resistors, so the user cannot change it. Values seen so
|
| H A D | ltc4261.rst | 44 registers. If a set of voltage divider resistors is installed, calculate the
|
| H A D | ltc2945.rst | 44 registers. If a set of voltage divider resistors is installed, calculate the
|
| /linux-6.15/Documentation/devicetree/bindings/hwmon/ |
| H A D | ntc-thermistor.yaml | 12 Thermistors with negative temperature coefficient (NTC) are resistors that
59 We can use both pull-up and pull-down resistors at the same time, and then
|
| H A D | adi,ltc2991.yaml | 16 sense resistors or temperature sensing transistors.
|
| /linux-6.15/Documentation/devicetree/bindings/net/ |
| H A D | motorcomm,yt8xxx.yaml | 59 be configured with hardware pull-up resistors to match the SOC voltage
76 be configured with hardware pull-up resistors to match the SOC voltage
|
| /linux-6.15/Documentation/devicetree/bindings/gpio/ |
| H A D | gpio-xra1403.txt | 5 - Internal pull-up resistors
|
| /linux-6.15/Documentation/devicetree/bindings/pinctrl/ |
| H A D | mediatek,mt6779-pinctrl.yaml | 162 Pull up settings for 2 pull resistors, R0 and R1. User can
174 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| H A D | mediatek,mt6795-pinctrl.yaml | 133 Pull up settings for 2 pull resistors, R0 and R1. User can
145 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| H A D | mediatek,mt8183-pinctrl.yaml | 146 Pull up settings for 2 pull resistors, R0 and R1. User can
158 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| H A D | mediatek,mt8365-pinctrl.yaml | 152 Pull up settings for 2 pull resistors, R0 and R1. User can
166 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| /linux-6.15/Documentation/devicetree/bindings/power/supply/ |
| H A D | richtek,rt9467.yaml | 18 integrated sensing resistors.
|
| /linux-6.15/arch/arm/boot/dts/st/ |
| H A D | stm32mp153c-lxa-fairytux2-gen2.dts | 101 * The required pull-up resistors however are on v3v3_hdmi.
|
| /linux-6.15/Documentation/devicetree/bindings/iio/imu/ |
| H A D | st,lsm6dsx.yaml | 80 description: enable/disable internal i2c controller pullup resistors.
|
| /linux-6.15/Documentation/ABI/stable/ |
| H A D | sysfs-class-udc | 63 Allows users to disconnect data pullup resistors thus causing a
|