| /linux-6.15/Documentation/ABI/testing/ |
| H A D | sysfs-bus-iio-dma-buffer | 5 DMA buffers tend to have a alignment requirement for the
6 buffers. If this alignment requirement is not met samples might
15 that the alignment requirement in samples sets might change
17 the alignment requirement reported in bytes by this property
|
| H A D | sysfs-firmware-lefi-boardinfo | 12 requirement and specific for Loongson64, so only add a new
|
| H A D | sysfs-firmware-gsmi | 34 requirement is that the blob be prefixed with a
|
| /linux-6.15/Documentation/devicetree/bindings/sound/ |
| H A D | realtek,rt5682s.yaml | 62 Set the clock rate (hz) for the requirement of the particular DMIC.
66 Set the delay time (ms) for the requirement of the particular DMIC.
70 Set the delay time (ms) for the requirement of the particular platform or AMIC.
|
| H A D | realtek,rt5682.yaml | 67 Set the clock rate (hz) for the requirement of the particular DMIC.
71 Set the delay time (ms) for the requirement of the particular DMIC.
|
| /linux-6.15/Documentation/bpf/ |
| H A D | btf.rst | 129 ``struct btf_type`` encoding requirement:
181 ``struct btf_type`` encoding requirement:
193 ``struct btf_type`` encoding requirement:
238 ``struct btf_type`` encoding requirement:
282 ``struct btf_type`` encoding requirement:
307 ``struct btf_type`` encoding requirement:
319 ``struct btf_type`` encoding requirement:
331 ``struct btf_type`` encoding requirement:
343 ``struct btf_type`` encoding requirement:
355 ``struct btf_type`` encoding requirement:
[all …]
|
| /linux-6.15/Documentation/kbuild/ |
| H A D | Kconfig.recursion-issue-02 | 11 # drivers if they share a common core requirement and use disjoint semantics to
14 # core requirement, and one uses "select" while the other uses "depends on" to
|
| /linux-6.15/drivers/gpu/drm/tegra/ |
| H A D | dp.c | 395 unsigned long requirement, capacity; in drm_dp_link_choose() local
400 requirement = mode->clock * info->bpc * 3; in drm_dp_link_choose()
414 if (capacity >= requirement) { in drm_dp_link_choose()
416 lanes[i], rates[j], requirement, in drm_dp_link_choose()
|
| /linux-6.15/Documentation/fb/ |
| H A D | sh7760fb.rst | 14 of Area3 (HW requirement). Because of this requirement you should NOT
|
| /linux-6.15/Documentation/devicetree/bindings/dma/stm32/ |
| H A D | st,stm32-dma3.yaml | 66 -bit 4-7: The FIFO requirement for queuing source/destination transfers
67 0x0: no FIFO requirement/any channel can fit
|
| /linux-6.15/Documentation/devicetree/bindings/regulator/ |
| H A D | richtek,rt4831-regulator.yaml | 17 It is sufficient to meet the current LCD power requirement.
|
| /linux-6.15/Documentation/devicetree/bindings/net/ |
| H A D | marvell,mvusb.yaml | 17 Since the device is connected over USB, there is no strict requirement of
|
| /linux-6.15/Documentation/power/regulator/ |
| H A D | design.rst | 28 requirement to do any runtime configuration of their power beyond
|
| /linux-6.15/Documentation/power/ |
| H A D | pm_qos_interface.rst | 193 whatever is necessary to transfer the effective requirement value to the
202 the hardware supports a special "no requirement" setting, the callback is
211 requirement for the device, if any. Writing "any" to it means "no requirement,
|
| /linux-6.15/Documentation/input/devices/ |
| H A D | sentelic.rst | 513 Register inversion requirement:
520 Register swapping requirement:
538 inverted(refer to the 'Register inversion requirement' section),
546 swapped(refer to the 'Register swapping requirement' section),
577 inverted(refer to the 'Register inversion requirement' section),
585 swapped(refer to the 'Register swapping requirement' section),
599 inverted(refer to the 'Register inversion requirement' section),
607 swapped(refer to the 'Register swapping requirement' section),
672 inverted(refer to the 'Register inversion requirement' section),
680 swapped(refer to the 'Register swapping requirement' section),
|
| H A D | cs461x.rst | 22 behavior in my case was not raised the requirement of joystick calibration.
|
| /linux-6.15/Documentation/devicetree/bindings/mfd/ |
| H A D | richtek,rt4831.yaml | 17 It's sufficient to meet the current LCD power requirement.
|
| /linux-6.15/Documentation/devicetree/bindings/mmc/ |
| H A D | synopsys-dw-mshc-common.yaml | 56 data done irq. Add this watermark quirk to mark this requirement and
|
| /linux-6.15/Documentation/trace/coresight/ |
| H A D | panic.rst | 85 itself. Persistent RAM is not a requirement in this case.
89 Crashdump kernel is not a requirement in this case. Persistent RAM
103 Note: This is a requirement for watchdog reset case but optional
|
| /linux-6.15/Documentation/arch/powerpc/ |
| H A D | booting.rst | 18 The main requirement that will be defined in more detail below is the presence
24 requirement to have a node for PCI host bridges in order to provide interrupt
|
| /linux-6.15/arch/arc/boot/dts/ |
| H A D | axc001.dtsi | 116 * no strict requirement for a frame-buffer to be in any
|
| /linux-6.15/Documentation/devicetree/bindings/ |
| H A D | common-properties.txt | 28 a requirement. Some implementations assume that little-endian is
|
| /linux-6.15/drivers/hid/bpf/progs/ |
| H A D | README | 5 when you have such a device, but they should not be a requirement for a device
|
| /linux-6.15/Documentation/devicetree/bindings/net/dsa/ |
| H A D | nxp,sja1105.yaml | 12 cs_sck_delay of 500ns. Ensuring that this SPI timing requirement is observed
|
| /linux-6.15/Documentation/RCU/Design/Requirements/ |
| H A D | Requirements.rst | 626 fundamental RCU requirement that a grace period wait for all
629 requirement. Of course, different implementations enforce this
630 requirement in different ways, but enforce it they must.
1172 awakening idle CPUs. I cannot claim that this requirement was
1626 Mathieu Desnoyers made me aware of this requirement, and also
1720 me of this requirement.
1841 with this requirement; he also kindly surprised me with `an
1843 that meets this requirement.
1851 And yes, I also learned of this requirement the hard way.
1878 Nikita Danilov noted this requirement for an analogous
[all …]
|