| /linux-6.15/drivers/net/dsa/mv88e6xxx/ |
| H A D | leds.c | 100 bool fiber; member
153 .fiber = true,
161 .fiber = true,
183 .fiber = true,
191 .fiber = true,
211 .fiber = true,
338 bool fiber, unsigned long rules, u16 *selector) in mv88e6xxx_led_match_selector() argument
368 if (conf->fiber != fiber) in mv88e6xxx_led_match_selector()
426 bool fiber, unsigned long rules, u16 *selector) in mv88e6xxx_led_get_selector() argument
585 return mv88e6xxx_led_get_selector(p, 0, p->fiber, rules, &selector); in mv88e6xxx_led0_hw_control_is_supported()
[all …]
|
| H A D | chip.h | 298 bool fiber; member
|
| H A D | chip.c | 3392 p->fiber = fwnode_property_present(port_fwnode, "sfp"); in mv88e6xxx_setup_port()
|
| /linux-6.15/Documentation/devicetree/bindings/net/ |
| H A D | micrel.txt | 40 - micrel,fiber-mode: If present the PHY is configured to operate in fiber mode
42 Some PHYs, such as the KSZ8041FTL variant, support fiber mode, enabled
44 registers whether the PHY is in fiber mode, so this boolean device tree
47 In fiber mode, auto-negotiation is disabled and the PHY can only work in
|
| H A D | ti,dp83822.yaml | 17 fiber-optic transceiver. Additionally, the DP83822 provides flexibility to
36 This property is only applicable if the fiber mode support is strapped
39 ti,fiber-mode:
43 If present the DP83822 PHY is configured to operate in fiber mode
46 If the fiber mode is not strapped then signal detection for the PHY
48 In fiber mode, auto-negotiation is disabled and the PHY can only work in
|
| H A D | qcom,qca807x.yaml | 19 MAC, while second one is SGMII for connection to MAC or fiber.
22 100BASE-FX fiber.
|
| H A D | keystone-netcp.txt | 101 - mac<->fiber mode: 3
|
| /linux-6.15/drivers/net/fddi/ |
| H A D | Kconfig | 12 run over copper or fiber. If you are connected to such a network and
23 This is support for the DEC FDDIcontroller 700 (DEFZA-AA, fiber)
|
| /linux-6.15/drivers/net/ethernet/alacritech/ |
| H A D | Kconfig | 24 both copper and fiber.
|
| /linux-6.15/drivers/net/hippi/ |
| H A D | Kconfig | 12 can run over copper (25m) or fiber (300m on multi-mode or 10km on
|
| /linux-6.15/drivers/net/phy/ |
| H A D | marvell.c | 1665 int fiber, int status) in marvell_read_status_page_an() argument
1694 if (!fiber) { in marvell_read_status_page_an()
1736 int fiber; in marvell_read_status_page() local
1755 fiber = 1; in marvell_read_status_page()
1757 fiber = 0; in marvell_read_status_page()
1764 phydev->port = fiber ? PORT_FIBRE : PORT_TP; in marvell_read_status_page()
1766 if (fiber) { in marvell_read_status_page()
1780 err = marvell_read_status_page_an(phydev, fiber, status); in marvell_read_status_page()
|
| H A D | Kconfig | 406 fiber connections.
|
| /linux-6.15/arch/arm64/boot/dts/hisilicon/ |
| H A D | hip06.dtsi | 579 media-type = "fiber";
587 media-type = "fiber";
|
| H A D | hip07.dtsi | 1488 media-type = "fiber";
1498 media-type = "fiber";
|
| /linux-6.15/drivers/net/dsa/microchip/ |
| H A D | ksz8.c | 1151 if (dev->ports[port].fiber) in ksz8_w_phy_bmcr()
1700 p->fiber = 1; in ksz8_config_cpu_port()
1702 if (p->fiber) in ksz8_config_cpu_port()
|
| H A D | ksz_common.h | 131 u32 fiber:1; /* port is fiber */ member
|
| /linux-6.15/Documentation/networking/device_drivers/ethernet/intel/ |
| H A D | e1000e.rst | 327 between copper-based adapters and fiber-based adapters.
349 An Intel(R) Ethernet Network Adapter using fiber-based connections, however,
|
| H A D | e1000.rst | 341 If the board uses a fiber interface, these keywords are ignored, and the
342 fiber interface board only links at 1000 Mbps full-duplex.
|
| H A D | i40e.rst | 382 between copper-based adapters and fiber-based adapters.
407 An Intel(R) Ethernet Network Adapter using fiber-based connections, however,
|
| H A D | ixgbe.rst | 100 "ifconfig ethX down" turns off the laser for 82599-based SFP+ fiber adapters.
|
| H A D | ice.rst | 706 between copper-based adapters and fiber-based adapters.
|
| /linux-6.15/Documentation/networking/device_drivers/ethernet/dlink/ |
| H A D | dl2k.rst | 232 available for fiber adapter.
|
| /linux-6.15/drivers/staging/most/Documentation/ |
| H A D | driver_usage.txt | 11 fiber optics, unshielded twisted pair cables (UTP) and coax cables. MOST
|
| /linux-6.15/Documentation/networking/device_drivers/ethernet/cirrus/ |
| H A D | cs89x0.rst | 71 or fiber networks).
|