| /linux-6.15/Documentation/w1/slaves/ |
| H A D | w1_therm.rst | 32 read sequence will initiate a temperature conversion, then provide two
46 in the module), it will drive the line high during the longer conversion
48 ``therm_bulk_read`` will return 0 if no bulk conversion pending,
49 -1 if at least one sensor still in conversion, 1 if conversion is complete
52 may return empty if conversion is still in progress. Note that if a bulk
57 A strong pullup will be applied during the conversion if required.
59 ``conv_time`` is used to get current conversion time (read), and
65 auto measure and set a conversion time by writing ``1`` to
66 ``conv_time``; 3) use ``features`` to enable poll for conversion
68 the default conversion time write ``0`` to ``conv_time``.
[all …]
|
| /linux-6.15/Documentation/ABI/testing/ |
| H A D | sysfs-driver-w1_therm | 81 a conversion and send the result. Note that the
82 conversion duration depend on the resolution (if
115 (RW) trigger a bulk read conversion. read the status
119 conversion in progress on at least 1 sensor
121 conversion complete but at least one sensor
125 trigger a conversion on each device
145 reset to default (datasheet) conversion time for a new
149 Actual conversion time in milliseconds.
156 temperature conversion, measure an actual value.
158 conversion time can be obtained by reading this
[all …]
|
| H A D | sysfs-bus-iio-vf610 | 5 Specifies the hardware conversion mode used. The three
14 Specifies the hardware conversion mode used within DAC.
|
| H A D | sysfs-bus-iio-ina2xx-adc | 8 buffer. This synchronizes the in-chip conversion rate with the
14 or repeated, depending on the beat between the capture and conversion
|
| /linux-6.15/Documentation/hwmon/ |
| H A D | ina3221.rst | 23 and supply voltage, with programmable conversion times and averaging, current
62 update_interval Data conversion time in millisecond, following:
68 * BC: bus-voltage conversion time in millisecond
69 * SC: shunt-voltage conversion time in millisecond
71 Affects both Bus- and Shunt-voltage conversion time.
73 and SC to 140 us (minimum conversion time).
|
| H A D | lm73.rst | 33 affects the conversion time of the LM73's analog-to-digital converter.
35 conversion time via the 'update_interval' sysfs attribute for the
50 used to change the conversion time::
79 conversion time actively in use.
81 Mathematically, the resolution can be derived from the conversion time
|
| H A D | max31827.rst | 79 The conversion rate can be modified with update_interval attribute of the chip.
92 the conversion frequency to 1 conv/s. The conversion time varies depending on
95 The conversion time doubles with every bit of increased resolution. The
98 - 8 bit -> 8.75 ms conversion time
99 - 9 bit -> 17.5 ms conversion time
100 - 10 bit -> 35 ms conversion time
101 - 12 bit (default) -> 140 ms conversion time
112 triggered, the device waits for <conversion time> ms, and only after that is
113 the temperature value register read. Note that the conversion times are rounded
|
| H A D | max197.rst | 35 filled with a pointer to a conversion function, defined like::
39 ctrl is the control byte to write to start a new conversion.
50 3 BIP Unipolar or Bipolar conversion mode
58 in[0-7]_input The conversion value for the corresponding channel.
|
| H A D | ina2xx.rst | 84 programmable conversion times and filtering.
101 programmable calibration value and conversion times. The SY24655 can also
102 calculate average power for use in energy conversion.
111 bus and shunt voltage conversion times multiplied by the averaging rate. We
112 don't touch the conversion times and only modify the number of averages. The
145 update_interval data conversion time; affects number of samples used
|
| /linux-6.15/scripts/coccinelle/misc/ |
| H A D | boolconv.cocci | 2 /// Remove unneeded conversion to bool
5 //# explicit conversion is overly verbose and unneeded.
79 msg = "WARNING: conversion to bool not needed here"
90 msg = "WARNING: conversion to bool not needed here"
|
| /linux-6.15/Documentation/devicetree/bindings/input/touchscreen/ |
| H A D | adi,ad7879.yaml | 39 adi,first-conversion-delay:
84 adi,conversion-interval:
120 adi,first-conversion-delay = /bits/ 8 <3>;
124 adi,conversion-interval = /bits/ 8 <255>;
144 adi,first-conversion-delay = /bits/ 8 <3>;
148 adi,conversion-interval = /bits/ 8 <255>;
|
| H A D | fsl-mx25-tcq.txt | 1 Freescale mx25 TS conversion queue module
3 mx25 touchscreen conversion queue module which controls the ADC unit of the
24 This device includes two conversion queues which can be added as subnodes.
|
| /linux-6.15/Documentation/iio/ |
| H A D | ad7606.rst | 49 connected to the conversion trigger pin.
90 The conversion can be triggered by two distinct ways:
92 - A GPIO is connected to the conversion trigger pin, and this GPIO is controlled
94 conversion trigger pin to high as soon as it has read all the conversions.
96 - An external source is connected to the conversion trigger pin. In the
98 does not control directly the conversion trigger pin. Instead, it can
133 trigger is allocated and linked by the driver, and a new conversion is triggered
144 conversion pin, because the busy pin is bound to the backend.
|
| /linux-6.15/Documentation/devicetree/bindings/iio/adc/ |
| H A D | adi,max11410.yaml | 47 description: vref0p supply can be used as reference for conversion.
50 description: vref1p supply can be used as reference for conversion.
53 description: vref2p supply can be used as reference for conversion.
56 description: vref0n supply can be used as reference for conversion.
59 description: vref1n supply can be used as reference for conversion.
62 description: vref2n supply can be used as reference for conversion.
|
| H A D | adi,ad7476.yaml | 69 adi,conversion-start-gpios:
70 description: A GPIO used to trigger the start of a conversion
154 adi,conversion-start-gpios: true
157 adi,conversion-start-gpios: false
|
| H A D | fsl,vf610-adc.yaml | 48 Three values necessary to cover the 3 conversion modes.
57 to be chosen according to the conversion mode and the connected analog
60 C_as as well as conversion modes is 1000ns.
|
| H A D | adi,ad7779.yaml | 47 description: Front-End analog supply AVDD1. Can be used as conversion ref.
60 conversion independently of the interface selected to read back the
61 Σ-∆ conversion.
|
| /linux-6.15/tools/perf/Documentation/ |
| H A D | perf-data.txt | 21 It's possible to set data-convert debug variable to get debug messages from conversion,
28 Triggers the CTF conversion, specify the path of CTF data directory.
31 Triggers JSON conversion. Specify the JSON filename to output.
|
| /linux-6.15/Documentation/devicetree/bindings/mfd/ |
| H A D | fsl-imx25-tsadc.txt | 3 This device combines two general purpose conversion queues one used for general
15 conversion queues.
20 This device includes two conversion queues which can be added as subnodes.
|
| /linux-6.15/Documentation/devicetree/bindings/sound/ |
| H A D | cirrus,cs4234.yaml | 14 high performance analog to digital conversion, 4 channels of high
15 performance digital to analog conversion for audio, and 1 channel of
16 digital to analog conversion to provide a nondelayed audio reference
|
| /linux-6.15/Documentation/userspace-api/media/v4l/ |
| H A D | pixfmt-v4l2.rst | 116 conversion, it will return another supported colorspace.
117 The driver indicates that colorspace conversion is supported by setting
160 conversion, it will return another supported encoding.
162 ycbcr_enc conversion is supported by setting the flag
174 conversion, it will return another supported encoding.
176 that hsv_enc conversion is supported by setting the flag
190 conversion, it will return another supported quantization.
191 The driver indicates that quantization conversion is supported by setting
203 conversion, it will return another supported transfer function.
204 The driver indicates that xfer_func conversion is supported by setting
[all …]
|
| /linux-6.15/arch/arm/boot/dts/nxp/imx/ |
| H A D | imx6qdl-colibri-v1.2.dtsi | 16 adi,first-conversion-delay = /bits/ 8 <3>;
20 adi,conversion-interval = /bits/ 8 <255>;
|
| H A D | imx6qdl-apalis-v1.2.dtsi | 16 adi,first-conversion-delay = /bits/ 8 <3>;
20 adi,conversion-interval = /bits/ 8 <255>;
|
| /linux-6.15/net/ |
| H A D | Kconfig.debug | 37 During the conversion, rtnl_net_lock() just adds an extra
40 Once the conversion completes, rtnl_lock() will be removed
|
| /linux-6.15/Documentation/devicetree/bindings/media/i2c/ |
| H A D | tvp514x.txt | 6 to-digital (A/D) conversion of component RGB and YPbPr signals as well as A/D
7 conversion and decoding of NTSC, PAL and SECAM composite and S-video into
|