| /linux-6.15/Documentation/devicetree/bindings/iio/adc/ |
| H A D | adi,ad4000.yaml | 103 maximum: 102040816 # for VIO > 2.7 V, 81300813 for VIO > 1.7 V
112 pin is hard-wired to logic high (VIO). "low" indicates that it is
123 A 1.8V to 5.5V supply for the digital inputs and outputs (VIO).
169 # Single-channel PulSAR devices have SDI either tied to VIO, GND, or host CS.
199 maximum: 50000000 # for VIO > 2.7 V, 40000000 for VIO > 1.7 V
|
| H A D | adi,ad7944.yaml | 57 device on the bus. In this mode, SDI is tied to VIO, and the CNV line
|
| /linux-6.15/Documentation/iio/ |
| H A D | ad4000.rst | 69 hard-wired to digital input/output interface supply (VIO). In this setup, the
81 VIO +--------------------+ | HOST |
98 VIO +--------------------+ | HOST |
|
| H A D | ad7944.rst | 37 VIO +--------------------+ | HOST |
|
| /linux-6.15/fs/afs/ |
| H A D | afs_fs.h | 57 VIO = 112, /* I/O error in volume */ enumerator
|
| /linux-6.15/Documentation/devicetree/bindings/input/touchscreen/ |
| H A D | zet6223.txt | 10 - vio-supply : Specification for VIO supply (1.8V or 3.3V,
|
| /linux-6.15/arch/sh/kernel/cpu/sh4a/ |
| H A D | setup-sh7723.c | 469 DMAC1A, DMAC0A, VIO, DMAC0B, FLCTL, I2C, _2DG, enumerator
566 INTC_GROUP(VIO, VIO_CEUI,VIO_BEUI,VIO_VEU2HI,VIO_VOUI),
614 { 0xa4080010, 0, 16, 4, /* IPRE */ { DMAC0A, VIO, SCIFA_SCIFA0, VPU_VPUI } },
|
| H A D | setup-sh7724.c | 894 DMAC1A, _2DG, DMAC0A, VIO, USB, RTC, enumerator
1005 INTC_GROUP(VIO, VIO_CEU0, VIO_BEU0, VIO_VEU1, VIO_VOU),
1064 { 0xa4080010, 0, 16, 4, /* IPRE */ { DMAC0A, VIO, SCIFA3, VPU } },
|
| /linux-6.15/Documentation/devicetree/bindings/net/wireless/ |
| H A D | ti,wl1251.txt | 11 - vio-supply : phandle to regulator providing VIO
|
| /linux-6.15/Documentation/devicetree/bindings/mfd/ |
| H A D | richtek,rt4831.yaml | 36 Some usage directly tied this pin to follow VIO 1.8V power on sequence.
|
| H A D | tps65910.txt | 42 vccio-supply: VIO input.
51 vccio-supply: VIO input.
|
| H A D | twl6040.txt | 17 - vio-supply: Regulator for the twl6040 VIO supply
|
| /linux-6.15/Documentation/devicetree/bindings/iio/light/ |
| H A D | sharp,gp2ap002.yaml | 34 description: VIO power supply a phandle to a regulator
|
| /linux-6.15/drivers/regulator/ |
| H A D | tps68470-regulator.c | 115 TPS68470_REGULATOR(VIO, TPS68470_VIO, tps68470_always_on_reg_ops, 126,
|
| H A D | twl-regulator.c | 530 TWL4030_ADJUSTABLE_LDO(VIO, 0x4b, 14, 1000, 0x08);
565 TWL4030_OF_MATCH("ti,twl4030-vio", VIO),
|
| H A D | twl6030-regulator.c | 614 TWL6032_ADJUSTABLE_SMPS(VIO, 0x16);
672 TWLSMPS_OF_MATCH("ti,twl6032-vio", VIO),
|
| H A D | tps65910-regulator.c | 277 EXT_CONTROL_REG_BITS(VIO, 1, 0),
293 EXT_CONTROL_REG_BITS(VIO, 1, 0),
|
| /linux-6.15/arch/arm64/boot/dts/arm/ |
| H A D | vexpress-v2f-1xv7-ca53x2.dts | 124 /* VIO to expansion board above */
|
| /linux-6.15/Documentation/devicetree/bindings/media/i2c/ |
| H A D | mipi-ccs.yaml | 47 description: I/O voltage supply (VIO), sensor dependent.
|
| /linux-6.15/arch/arm/boot/dts/arm/ |
| H A D | vexpress-v2m-rs1.dtsi | 454 regulator-name = "VIO";
456 label = "VIO";
|
| H A D | vexpress-v2m.dtsi | 470 regulator-name = "VIO";
472 label = "VIO";
|
| /linux-6.15/arch/arm/boot/dts/nxp/mxs/ |
| H A D | imx28-btt3.dtsi | 295 no-1-8-v; /* force 3.3V VIO */
|
| /linux-6.15/Documentation/devicetree/bindings/net/can/ |
| H A D | ti,tcan4x5x.yaml | 117 Set nWKRQ to use VIO voltage rail.
|
| /linux-6.15/arch/arm/boot/dts/st/ |
| H A D | ste-ux500-samsung-gavini.dts | 480 /* Used for VIO for sensors */
481 regulator-name = "V-SENSORS-VIO";
|
| /linux-6.15/arch/arm/boot/dts/aspeed/ |
| H A D | aspeed-bmc-opp-mowgli.dts | 525 /* CP0 VDN & VIO : IR35221 */
|