| /linux-6.15/Documentation/hwmon/ |
| H A D | lochnagar.rst | 33 in1_input Measured voltage for 1V8 DSP (milliVolts)
34 in1_label "1V8 DSP"
35 curr2_input Measured current for 1V8 DSP (milliAmps)
36 curr2_label "1V8 DSP"
39 power2_label "1V8 DSP"
41 in2_label "1V8 CDC"
43 curr3_label "1V8 CDC"
46 power3_label "1V8 CDC"
55 in4_label "AVDD 1V8"
57 curr5_label "AVDD 1V8"
[all …]
|
| /linux-6.15/drivers/regulator/ |
| H A D | pcap-regulator.c | 118 VREG_INFO(V8, PCAP_REG_VREG2, 5, 6, 16, 22),
227 VREG(V8), VREG(V9), VREG(V10), VREG(VAUX1), VREG(VAUX2), VREG(VAUX3),
|
| /linux-6.15/arch/arm/boot/dts/broadcom/ |
| H A D | bcm2835-rpi-cm1.dtsi | 30 regulator-name = "1V8";
|
| H A D | bcm2837-rpi-cm3.dtsi | 22 regulator-name = "1V8";
|
| /linux-6.15/include/linux/mfd/ |
| H A D | ezx-pcap.h | 119 #define V8 7 macro
|
| /linux-6.15/arch/arm64/boot/dts/ti/ |
| H A D | k3-am642-evm-icssg1-dualemac-mii.dtso | 48 AM64X_IOPAD(0x00c4, PIN_INPUT, 1) /* (V8) PRG1_PRU0_GPO3.PR1_MII0_RXD3 */
|
| /linux-6.15/arch/x86/crypto/ |
| H A D | aes-ctr-avx-x86_64.S | 317 .set XCTR_IV, V8
319 .set BSWAP_MASK, V8
|
| /linux-6.15/arch/arm/boot/dts/gemini/ |
| H A D | gemini-nas4220b.dts | 110 pins = "V8 GMAC0 RXDV", "T10 GMAC1 RXDV";
|
| H A D | gemini-sq201.dts | 185 pins = "V8 GMAC0 RXDV";
|
| H A D | gemini-sl93512r.dts | 222 pins = "U8 GMAC0 RXD0", "V8 GMAC0 RXD1",
|
| H A D | gemini-dlink-dns-313.dts | 260 pins = "U8 GMAC0 RXD0", "V8 GMAC0 RXD1",
|
| /linux-6.15/arch/arm/boot/dts/renesas/ |
| H A D | r8a73a4-ape6evm.dts | 58 regulator-name = "1V8";
|
| /linux-6.15/arch/arm/boot/dts/ti/omap/ |
| H A D | am335x-boneblue.dts | 196 AM33XX_PADCONF(AM335X_PIN_GPMC_AD5, PIN_INPUT_PULLUP, MUX_MODE1) /* (V8) gpmc_ad5.mmc1_dat5 */
485 "MMC1_DAT5", /* V8 */
|
| /linux-6.15/arch/arm64/boot/dts/freescale/ |
| H A D | imx8mm-kontron-sl.dtsi | 147 regulator-name = "+1V8 (BUCK5)";
|
| H A D | imx8mq-mnt-reform2.dts | 71 regulator-name = "1V8";
|
| H A D | imx8mn-beacon-baseboard.dtsi | 52 regulator-name = "1V8";
|
| H A D | imx8mm-beacon-baseboard.dtsi | 68 regulator-name = "1V8";
|
| /linux-6.15/arch/arm64/boot/dts/amlogic/ |
| H A D | meson-gxl-s905x-libretech-cc-v2.dts | 153 regulator-name = "VCC 1V8";
|
| H A D | meson-g12b-bananapi-cm4-mnt-reform2.dts | 157 regulator-name = "1V8";
|
| H A D | meson-gxbb-odroidc2.dts | 283 gpio-line-names = "UART TX", "UART RX", "VCCK En", "TF 3V3/1V8 En",
|
| /linux-6.15/tools/perf/Documentation/ |
| H A D | perf-inject.txt | 79 if you are monitoring environment using JIT runtimes, such as Java, DART or V8.
|
| /linux-6.15/Documentation/devicetree/bindings/phy/ |
| H A D | phy-stm32-usbphyc.yaml | 52 description: regulator providing 1V8 power supply to the PLL block
|
| /linux-6.15/Documentation/arch/arm64/ |
| H A D | sve.rst | 521 Z8 | : * V8 |
554 This follows from the way these bits are mapped to V8..V15, which are caller-
578 * V8 | |
|
| /linux-6.15/arch/arm/boot/dts/st/ |
| H A D | stm32mp15xx-dhcor-avenger96.dtsi | 8 /* Avenger96 uses DHCOR SoM configured for 1V8 IO operation */
|
| /linux-6.15/arch/arm64/boot/dts/xilinx/ |
| H A D | zynqmp-zcu100-revC.dts | 521 interrupts = <76 IRQ_TYPE_EDGE_RISING>; /* MIO76 WLAN_IRQ 1V8 */
|