| /linux-6.15/Documentation/hwmon/ |
| H A D | smsc47b397.rst | 35 Methods for detecting the HP SIO and reading the thermal data on a dc7100
38 The thermal information on the dc7100 is contained in the SIO Hardware Monitor
90 The SIO counts the number of 90kHz (11.111us) pulses per revolution.
102 Obtaining the SIO version.
146 The following is an example of how to read the SIO Device ID located at 0x20:
164 The registers of interest for identifying the SIO on the dc7100 are Device ID
|
| H A D | lm70.rst | 47 complement digital temperature (sent via the SIO line), is available in the
|
| /linux-6.15/drivers/spi/ |
| H A D | spi-lm70llp.c | 64 #define SIO 0x10 macro
162 return ((SIO == (parport_read_status(pp->port) & SIO)) ? 0 : 1); in getmiso()
|
| /linux-6.15/arch/sh/kernel/cpu/sh4a/ |
| H A D | setup-sh7343.c | 318 SIOF0, SIOF1, SIO, enumerator
353 INTC_VECT(SIO, 0xd00),
392 { 0, 0, 0, SIO, Z3D4, 0, SIOF1, SIOF0 } },
415 { 0xa4080020, 0, 16, 4, /* IPRI */ { SIO, 0, TSIF, I2C1 } },
|
| H A D | setup-sh7722.c | 536 SCIF0, SCIF1, SCIF2, SIOF0, SIOF1, SIO, enumerator
566 INTC_VECT(SIOF1, 0xca0), INTC_VECT(SIO, 0xd00),
606 { 0, 0, 0, SIO, 0, 0, SIOF1, SIOF0 } },
631 { 0xa4080020, 0, 16, 4, /* IPRI */ { SIO, 0, TSIF, RTC } },
|
| /linux-6.15/Documentation/devicetree/bindings/pinctrl/ |
| H A D | microchip,sparx5-sgpio.yaml | 13 By using a serial interface, the SIO controller significantly extend
15 pins on the device. The primary purpose of the SIO controllers is to
|
| /linux-6.15/drivers/usb/serial/ |
| H A D | ftdi_sio.c | 51 SIO, enumerator
1104 [SIO] = "SIO", /* the serial part of FT8U100AX */
1295 case SIO: in get_ftdi_divisor()
1402 if (priv->chip_type == SIO || priv->chip_type == FT232A) in write_latency_timer()
1443 if (priv->chip_type == SIO || priv->chip_type == FT232A) in read_latency_timer()
1599 priv->chip_type = SIO; in ftdi_determine_type()
1734 if (type == SIO) in ftdi_is_visible()
1739 if (type == SIO || type == FT232A) in ftdi_is_visible()
2427 if (priv->chip_type == SIO) { in ftdi_prepare_write_buffer()
2811 if (priv->chip_type == SIO) in ftdi_get_modem_status()
|
| H A D | Kconfig | 173 Say Y here if you want to use a FTDI SIO single port USB to serial
|
| /linux-6.15/Documentation/scsi/ |
| H A D | qlogicfas.rst | 10 (including the Control Concepts SCSI/IDE/SIO/PIO/FDC cards).
|
| /linux-6.15/drivers/hwmon/ |
| H A D | asus_wmi_sensors.c | 117 SIO = 0x1, enumerator
|
| /linux-6.15/drivers/pinctrl/ |
| H A D | Kconfig | 396 Microchip SoCs. By using a serial interface, the SIO
399 device. The primary purpose of the SIO controller is to
|
| /linux-6.15/drivers/tty/serial/ |
| H A D | Kconfig | 860 bool "TMPTX39XX/49XX SIO support"
869 int "Maximum number of TMPTX39XX/49XX SIO ports"
874 bool "TMPTX39XX/49XX SIO Console support"
879 bool "TX39XX/49XX SIO act as standard serial"
|
| /linux-6.15/drivers/usb/gadget/udc/ |
| H A D | Kconfig | 382 for full speed USB devices, IDE, I2C, SIO, plus a USB host (OHCI).
|
| /linux-6.15/drivers/scsi/ |
| H A D | Kconfig | 1103 (including the Control Concepts SCSI/IDE/SIO/PIO/FDC cards).
|