Home
last modified time | relevance | path

Searched refs:OE (Results 1 – 25 of 32) sorted by relevance

12

/linux-6.15/arch/arm/boot/dts/st/
H A Dst-pincfg.h15 #define OE (1 << 27) macro
35 #define OUT (OE)
37 #define BIDIR (OE | OD)
39 #define BIDIR_PU (OE | PU | OD)
/linux-6.15/Documentation/devicetree/bindings/clock/
H A Didt,versaclock5.yaml38 SH SP Output when the SD/OE pin is Low/High
88 shut down if the SD/OE pin is driven high. If 0, this disables the
90 the value of the SD/OE pin. This property corresponds to the SH
97 If 1, this enables output when the SD/OE pin is high, and disables
98 output when the SD/OE pin is low. If 0, this disables output when
99 the SD/OE pin is high, and enables output when the SD/OE pin is
179 /* Set the SD/OE pin's settings */
/linux-6.15/Documentation/devicetree/bindings/display/ti/
H A Dti,tpd12s015.txt8 - gpios: CT CP HPD, LS OE and HPD gpios
21 <&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */
H A Dti,omap-dss.txt148 <&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */
/linux-6.15/Documentation/devicetree/bindings/display/bridge/
H A Dti,tdp158.yaml23 # OE = L: Power Down Mode
24 # OE = H: Normal Operation
H A Dthine,thc63lvd1024.yaml65 description: Output enable GPIO signal, pin name "OE", active high.
/linux-6.15/Documentation/devicetree/bindings/memory-controllers/
H A Dqcom,ebi2-peripheral-props.yaml17 The time the memory continues to drive the data bus after OE
77 The number of cycles elapsed before an OE assertion, with
87 assertion to OE assertion.
H A Dti,gpmc-child.yaml75 # OE signals timings corresponding to GPMC_CONFIG4:
149 description: OE signal is delayed by half GPMC clock
H A Darm,pl172.txt71 enable (OE signal) in nano seconds.
H A Dqcom,ebi2.yaml16 data lines (16 bits), OE (output enable), ADV (address valid, used on some
/linux-6.15/arch/arm/boot/dts/ti/omap/
H A Dam57xx-beagle-x15-revc.dts14 <&gpio2 30 GPIO_ACTIVE_HIGH>, /* gpio2_30, LS OE */
H A Dam57xx-beagle-x15-revb1.dts14 <&gpio2 30 GPIO_ACTIVE_HIGH>, /* gpio2_30, LS OE */
H A Dam57xx-beagle-x15.dts15 <&gpio6 28 GPIO_ACTIVE_HIGH>, /* gpio6_28, LS OE */
H A Domap5-uevm.dts187 <&gpio9 1 GPIO_ACTIVE_HIGH>, /* TCA6424A P00, LS OE */
H A Ddra76-evm.dts178 <&gpio7 31 GPIO_ACTIVE_HIGH>, /* gpio7_31, LS OE */
/linux-6.15/Documentation/devicetree/bindings/media/i2c/
H A Daptina,mt9v111.yaml31 description: Enable signal, pin name "OE#". Active low.
H A Dchrontel,ch7322.yaml41 Reference to the GPIO connected to the OE pin, if any. When low
/linux-6.15/Documentation/devicetree/bindings/bus/
H A Dnvidia,tegra20-gmi.txt49 - nvidia,snor-oe-active-high: WE/OE signal is active high
67 - nvidia,snor-oe-width: Number of cycles during which OE stays asserted.
/linux-6.15/Documentation/devicetree/bindings/gpio/
H A Dfairchild,74hc595.yaml50 description: GPIO connected to the OE (Output Enable) pin.
/linux-6.15/arch/arm/boot/dts/nxp/imx/
H A Dimx6ull-colibri-aster.dtsi68 * 127 - Voltage Level Translator OE# signal (IC11 and IC12)
/linux-6.15/Documentation/i2c/busses/
H A Di2c-mlxcpld.rst38 OE (output enable) is delayed by value set to this register
/linux-6.15/Documentation/devicetree/bindings/mips/cavium/
H A Dbootbus.txt36 - cavium,t-oe: A cell specifying the OE timing (in nS).
/linux-6.15/arch/arm/boot/dts/marvell/
H A Ddove-sbc-a510.dts62 * 1.5 Camera Input FPC OE and P21.19
/linux-6.15/Documentation/devicetree/bindings/pinctrl/
H A Dpinctrl-st.txt8 When a pin is in GPIO mode, Output Enable (OE), Open Drain(OD), and
/linux-6.15/drivers/pinctrl/renesas/
H A Dpinctrl-rzv2m.c86 #define OE(n) (0x04 + (n) * 0x40) macro
765 rzv2m_writel_we(pctrl->base + OE(port), bit, output); in rzv2m_gpio_set_direction()

12