Home
last modified time | relevance | path

Searched refs:HIGH (Results 1 – 25 of 71) sorted by relevance

123

/linux-6.15/arch/arm64/boot/dts/rockchip/
H A Drk3588-jaguar-pre-ict-tester.dtso81 * LOW. The signal shall not read HIGH in the event
89 * rail. It should be HIGH if all is properly soldered.
108 * soldering issue on GPIO3_B2 reports HIGH but proper
114 * rail. It should be HIGH if all is properly soldered.
119 * - GPIO3_C6 is floating (so HIGH) if GPIO3_C6 is not
123 * - GPIO3_C6 is HIGH if everything is proper,
126 * soldering reports HIGH.
132 * It should be HIGH if all is properly soldered.
142 * It should be HIGH if all is properly soldered.
152 * It should be HIGH if all is properly soldered.
[all …]
H A Drk3368-evb.dtsi225 rockchip,hw-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
/linux-6.15/Documentation/devicetree/bindings/media/i2c/
H A Dov7670.txt13 - hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
14 - vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
H A Dtvp5150.txt44 - hsync-active: Active state of the HSYNC signal. Must be <1> (HIGH).
45 - vsync-active: Active state of the VSYNC signal. Must be <1> (HIGH).
/linux-6.15/Documentation/devicetree/bindings/regulator/
H A Dgpio-regulator.yaml47 1: HIGH
72 description: Polarity of "enable-gpio" GPIO is active HIGH. Default is
H A Dfcs,fan53555.yaml48 VSEL0 register. When this pin is HIGH, VOUT is set by the VSEL1 register.
H A Dmaxim,max8973.yaml40 1 for HIGH and 0 for LOW.
/linux-6.15/arch/arm64/boot/dts/renesas/
H A Dhihope-rzg2-ex-lvds.dtsi21 * When GP1_20 is HIGH LVDS0 is connected to the LT8918L
/linux-6.15/Documentation/devicetree/bindings/iio/dac/
H A Dadi,ad8460.yaml96 or sleep mode, pulse SDN_RESET HIGH, then leave LOW.
101 LOW and then HIGH to reset all digital registers to default
/linux-6.15/include/linux/mfd/
H A Dtps65010.h124 #define HIGH 1 macro
/linux-6.15/arch/arm/boot/dts/rockchip/
H A Drk3228-evb.dts67 rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
/linux-6.15/drivers/s390/crypto/
H A Dzcrypt_msgtype6.h108 #define HIGH 500 macro
/linux-6.15/arch/arm/boot/dts/nxp/imx/
H A Dimx6qdl-mba6.dtsi422 /* HYS = 1, DSE = 111, 100k up, SPEED = HIGH */
507 /* HYS = 1, DSE = 110, 100k up, SPEED = HIGH (11)*/
537 /* HYS = 1, DSE = 110, PUE+PKE, SPEED = HIGH (11)*/
H A Dimx6q-bosch-acc.dts441 connect-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; /* Old: 0, SS: HIGH */
442 intn-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>; /* Old: 1, SS: HIGH */
443 reset-gpios = <&gpio5 5 GPIO_ACTIVE_LOW>; /* Old: 0, SS: HIGH */
/linux-6.15/Documentation/userspace-api/media/cec/
H A Dcec-ioc-dqevent.rst160 * .. _`CEC-EVENT-PIN-CEC-HIGH`:
176 * .. _`CEC-EVENT-PIN-HPD-HIGH`:
194 * .. _`CEC-EVENT-PIN-5V-HIGH`:
/linux-6.15/Documentation/devicetree/bindings/media/
H A Dvideo-interfaces.yaml118 Active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
124 Active state of the VSYNC signal, 0/1 for LOW/HIGH respectively. Note,
157 Active state of Sync-on-green (SoG) signal, 0/1 for LOW/HIGH respectively.
/linux-6.15/Documentation/devicetree/bindings/thermal/
H A Drockchip-thermal.yaml70 description: The hardware-controlled active polarity 0:LOW 1:HIGH.
/linux-6.15/Documentation/devicetree/bindings/clock/
H A Dsilabs,si5351.yaml137 1 - clock output is driven HIGH when disabled
138 2 - clock output is FLOATING (HIGH-Z) when disabled
/linux-6.15/Documentation/devicetree/bindings/mfd/
H A Dmax77620.txt122 GPIO1/nRST_IO pins are HIGH only if all rails
123 that have POK control enabled are HIGH.
H A Dtps6507x.txt30 1: If defdcdc pin of DCDC2/DCDC3 is driven HIGH.
/linux-6.15/drivers/nfc/st95hf/
H A Dcore.c75 #define HIGH 1 macro
453 gpiod_set_value(st95con->enable_gpiod, HIGH); in st95hf_send_st95enable_negativepulse()
465 gpiod_set_value(st95con->enable_gpiod, HIGH); in st95hf_send_st95enable_negativepulse()
/linux-6.15/arch/arm/mach-omap1/
H A Dboard-osk.c223 tps65010_set_gpio_out_value(GPIO2, HIGH); in osk_tps_setup()
/linux-6.15/Documentation/devicetree/bindings/iio/adc/
H A Dadi,ad7191.yaml35 Must be present when CLKSEL pin is tied HIGH to select external clock
/linux-6.15/Documentation/iio/
H A Dad7191.rst68 - When CLKSEL pin is tied HIGH: Requires external clock source
/linux-6.15/Documentation/leds/
H A Dleds-lm3556.rst24 or by pulling the STROBE pin HIGH.

123