Home
last modified time | relevance | path

Searched refs:CAM (Results 1 – 25 of 52) sorted by relevance

123

/freebsd-14.2/sys/amd64/conf/
H A DGENERIC-MMCCAM1 # MMCCAM is the kernel config for doing MMC on CAM development
24 # CAM-specific stuff
/freebsd-14.2/sys/cam/ctl/
H A DREADME.ctl.txt2 CTL - CAM Target Layer Description
76 This is visible through the CTL CAM SIM. This allows using CTL without
170 - Fixed the phantom device problem in the CTL CAM SIM and improved the
171 CAM SIM to automatically trigger a rescan when the port is enabled and
237 - Switch CTL over to using CAM CCBs instead of its own union ctl_io. This
240 will also require changes to the CAM CCB structure to support CTL.
325 CTL-specific wrappers around the CAM sense building functions.
337 This is a CTL frontend port that is also a CAM SIM. The idea is that this
351 conceptually very similar to CAM's union ccb.
369 CTL wrappers around CAM sense printing functions.
[all …]
/freebsd-14.2/sys/dev/sym/
H A DREADME.sym12 * This driver for FreeBSD-CAM is derived from the Linux sym53c8xx driver.
24 * FreeBSD-CAM services is based on the aic7xxx driver for FreeBSD-CAM
/freebsd-14.2/tools/test/stress2/misc/
H A Dall.exclude7 dd.sh CAM stuck in vmwait 20200116
25 gjournal4.sh CAM stuck in vmwait 20180517
49 overcommit2.sh CAM stuck in vmwait seen 20200112
/freebsd-14.2/tools/tools/scsi-defects/
H A DREADME5 This has not been ported CAM yet.
/freebsd-14.2/tools/kerneldoc/subsys/
H A DDoxyfile-cam6 PROJECT_NAME = "FreeBSD kernel CAM code"
/freebsd-14.2/sys/conf/
H A Dstd.nodebug26 # CAM debugging
H A Dstd.debug28 # CAM debugging
/freebsd-14.2/sys/contrib/device-tree/Bindings/pci/
H A Dhost-generic-pci.yaml26 For CAM, this 24-bit offset is:
38 description: Depends on the layout of configuration space (CAM vs ECAM
85 CAM or ECAM compliant PCI host controllers without any quirks
/freebsd-14.2/tools/tools/vhba/
H A DREADME12 are pretty much used to stress and test the FreeBSD CAM framework
/freebsd-14.2/sys/contrib/device-tree/Bindings/devfreq/
H A Dexynos-bus.txt81 |--- CAM
94 |--- CAM
112 |--- CAM
169 |--- CAM
/freebsd-14.2/sys/cam/
H A DREADME.quirks17 involving CAM and UMASS but is applicable to other areas.
19 CAM provides a generic transport for SCSI-like devices. Many different
60 causes FreeBSD to only send 10-byte commands. Since the CAM subsystem
108 reset the UA either, and so CAM runs in circles trying to retrieve
/freebsd-14.2/sys/contrib/device-tree/Bindings/interconnect/
H A Dsamsung,exynos-bus.yaml61 |--- CAM
103 |--- CAM
121 |--- CAM
/freebsd-14.2/sys/contrib/device-tree/src/arm64/freescale/
H A Dimx8-apalis-eval.dtsi60 /* Apalis I2C3 (CAM) */
H A Dimx8-apalis-ixora-v1.1.dtsi100 /* Apalis I2C3 (CAM) */
H A Dimx8-apalis-ixora-v1.2.dtsi138 /* Apalis I2C3 (CAM) */
/freebsd-14.2/sys/dev/firewire/
H A D00README48 - You need CAM(SCSI) support in your kernel.
50 2002/4/8, you need to apply CAM-patch in this archive
/freebsd-14.2/sys/contrib/device-tree/src/arm/
H A Dexynos5800.dtsi164 label = "CAM";
H A Dimx6q-apalis-eval.dts80 * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
H A Dimx6q-apalis-ixora.dts85 * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
H A Dtegra124-apalis-eval.dts105 * CAM_I2C: I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor
H A Dtegra124-apalis-v1.2-eval.dts101 * CAM_I2C: I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor
H A Dimx6q-apalis-ixora-v1.2.dts136 * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
/freebsd-14.2/sys/arm/conf/
H A DALPINE68 #device ctl # CAM Target Layer
/freebsd-14.2/sys/contrib/device-tree/Bindings/devfreq/event/
H A Dsamsung,exynos-ppmu.yaml18 each IP (DMC, CPU, RIGHTBUS, LEFTBUS, CAM interface, LCD, G3D, MFC). The

123