Home
last modified time | relevance | path

Searched refs:pulled (Results 1 – 25 of 34) sorted by relevance

12

/f-stack/freebsd/contrib/device-tree/Bindings/iio/pressure/
H A Dhp03.txt7 it must be pulled HI before the conversion and
9 pulled LO afterward.
/f-stack/freebsd/contrib/device-tree/Bindings/sound/
H A Deverest,es7241.txt15 the sdout. If the sdout is pulled down, leftj format is used.
16 If this property is not provided, sdout is assumed to pulled
/f-stack/freebsd/contrib/device-tree/Bindings/iio/light/
H A Dveml6030.yaml34 - 0x10 # ADDR pin pulled down
35 - 0x48 # ADDR pin pulled up
/f-stack/dpdk/drivers/net/fm10k/base/
H A Dfm10k_mbx.c355 end = fm10k_fifo_head_offset(fifo, mbx->pulled); in fm10k_mbx_write_copy()
395 mbx->pulled += mbx->tail_len - ack; in fm10k_mbx_pull_head()
399 len = fm10k_fifo_used(fifo) - mbx->pulled; in fm10k_mbx_pull_head()
409 len && (mbx->pulled >= len); in fm10k_mbx_pull_head()
411 mbx->pulled -= fm10k_fifo_head_drop(fifo); in fm10k_mbx_pull_head()
632 head = fm10k_fifo_head_offset(&mbx->tx, mbx->pulled); in fm10k_mbx_update_local_crc()
1083 mbx->pulled += mbx->tail_len - ack; in fm10k_mbx_reset_work()
1089 if (mbx->pulled >= len) in fm10k_mbx_reset_work()
1090 mbx->pulled -= len; in fm10k_mbx_reset_work()
1092 mbx->pulled = 0; in fm10k_mbx_reset_work()
[all …]
H A Dfm10k_mbx.h269 u16 tail, tail_len, pulled; member
/f-stack/freebsd/contrib/device-tree/Bindings/gpio/
H A Dgpio-max3191x.txt31 pulled high (8-bit mode). Use this if the modesel pin
35 that modesel is pulled low (16-bit mode).
H A Dgpio-pcf857x.txt40 the input (pulled-up) state. When the bit is set to one, the line will be
/f-stack/freebsd/contrib/device-tree/Bindings/mfd/
H A Dsamsung,sec-core.txt35 - samsung,s2mps11-wrstbi-ground: Indicates that WRSTBI pin of PMIC is pulled
40 register to turn off the power. Usually the ACOKB is pulled up to VBATT so
H A Dtps6507x.txt29 0: If defdcdc pin of DCDC2/DCDC3 is pulled to GND.
/f-stack/freebsd/contrib/device-tree/Bindings/iio/dac/
H A Dti,dac7612.txt7 The internal DACs are loaded when the LOADDACS pin is pulled down.
H A Dad5592r.txt41 * CH_OFFSTATE_PULLDOWN (the pin is pulled down)
/f-stack/freebsd/contrib/device-tree/Bindings/extcon/
H A Dqcom,pm8941-misc.txt4 the USB ID pin has been pulled low or high.
/f-stack/freebsd/contrib/device-tree/src/powerpc/fsl/
H A Dp1023rdb.dts186 /* IRQ[0:3] are pulled up on board, set to active-low */
212 * IRQ[7] is pulled up on board, set to active-low
238 * IRQ[8:10] are pulled up on board, set to active-low
/f-stack/freebsd/contrib/device-tree/Bindings/pinctrl/
H A Dpinctrl-stmfx.txt26 - bias-pull-up: the pin will be pulled up.
28 - bias-pull-down: the pin will be pulled down.
/f-stack/freebsd/contrib/device-tree/Bindings/leds/
H A Dleds-ktd2692.txt10 Also, When the AUX pin is pulled high while CTRL pin is high,
/f-stack/freebsd/contrib/device-tree/Bindings/net/wireless/
H A Dmediatek,mt76.txt30 data should be pulled from the OTP ROM
/f-stack/freebsd/contrib/device-tree/src/arm/
H A Dpxa3xx.dtsi88 * the configured driven and pulled levels match, so if there is a need for
89 * non-LPM pulled output, the same configuration could probably be used.
H A Dam335x-bonegreen-wireless.dts112 /* BT_AUD_OUT from wl1835 has to be pulled low when WL_EN is activated.*/
H A Dsun4i-a10-pcduino2.dts47 * is controlled by the PD2 pin (pulled-up by default). Also one of
H A Domap3-evm-processor-common.dtsi135 * Note that gpio_150 pulled high with internal pull to prevent wlcore
H A Dsun5i-gr8-evb.dts315 * through a GPIO or to the PMIC, and it is pulled down,
H A Dimx6qdl-hummingboard.dtsi280 * We want it pulled down for a fixed host connection.
H A Dqcom-apq8060-dragonboard.dts539 * GPIO17 is pulled high by a 10k
933 /* External micro SD card, directly connected, pulled up to 2.85 V */
/f-stack/freebsd/contrib/device-tree/Bindings/usb/
H A Dexynos-usb.txt23 needs to be pulled up for the bus to be powered.
/f-stack/dpdk/doc/guides/nics/
H A Dvmxnet3.rst40 which are eventually pulled by the PMD.

12