| /f-stack/freebsd/contrib/device-tree/Bindings/fpga/ |
| H A D | altera-passive-serial.txt | 15 - nconfig-gpios: config pin (referred to as nCONFIG in the manual) 16 - nstat-gpios: status pin (referred to as nSTATUS in the manual) 19 - confd-gpios: confd pin (referred to as CONF_DONE in the manual)
|
| H A D | xilinx-slave-serial.txt | 16 - prog_b-gpios: config pin (referred to as PROGRAM_B in the manual) 17 - done-gpios: config status pin (referred to as DONE in the manual) 21 (referred to as INIT_B in the manual)
|
| /f-stack/freebsd/contrib/device-tree/Bindings/clock/ |
| H A D | renesas,emev2-smu.txt | 6 System Management Unit described in user's manual R19UH0037EJ1000_SMU. 15 "Serial clock generator" in fig."Clock System Overview" of the manual, 28 fig."Clock System Overview" of the manual.
|
| /f-stack/freebsd/contrib/device-tree/Bindings/phy/ |
| H A D | brcm-sata-phy.txt | 36 "manual" (brcm,rxaeq-value is used in that case) 38 - brcm,rxaeq-value: when 'rxaeq-mode' is set to "manual", provides the RX
|
| /f-stack/freebsd/contrib/device-tree/Bindings/thermal/ |
| H A D | qoriq-thermal.txt | 14 the SoC reference manual. The first cell is TTR0CR, the second is 17 calibration data, as specified by the SoC reference manual.
|
| H A D | qoriq-thermal.yaml | 35 reference manual. The first cell is TTR0CR, the second is TTR1CR, etc. 42 specified by the SoC reference manual. The first cell of each pair
|
| /f-stack/freebsd/contrib/device-tree/Bindings/net/ |
| H A D | hisilicon-hns-dsaf.txt | 31 user manual. 44 depends on the hardware user manual. 46 value depends on the hardware user manual.
|
| /f-stack/freebsd/contrib/device-tree/Bindings/usb/ |
| H A D | mediatek,mtu3.txt | 40 is set as "otg", and meanwhile the property "mediatek,enable-manual-drd" 49 - enable-manual-drd : supports manual dual-role switch via debugfs; usually
|
| /f-stack/freebsd/contrib/device-tree/Bindings/pinctrl/ |
| H A D | fsl,imx27-pinctrl.txt | 35 described in the reference manual. 92 are defined in the i.MX27 reference manual.
|
| /f-stack/freebsd/contrib/device-tree/Bindings/interrupt-controller/ |
| H A D | riscv,cpu-intc.txt | 10 The RISC-V supervisor ISA manual specifies three interrupt sources that are 29 RISC-V supervisor ISA manual, with only the following three interrupts being
|
| /f-stack/freebsd/contrib/device-tree/Bindings/sound/ |
| H A D | eukrea-tlv320.txt | 16 hardware manual.
|
| /f-stack/freebsd/contrib/device-tree/Bindings/serial/ |
| H A D | fsl,s32-linflexuart.txt | 6 See chapter 47 ("LINFlexD") in the reference manual[1].
|
| /f-stack/freebsd/contrib/device-tree/src/arm64/mediatek/ |
| H A D | mt2712-evb.dts | 204 //enable-manual-drd; 216 enable-manual-drd;
|
| /f-stack/freebsd/contrib/device-tree/Bindings/net/can/ |
| H A D | bosch,m_can.yaml | 68 M_CAN includes the following elements according to user manual: 78 M_CAN user manual for details.
|
| /f-stack/tools/libxo/doc/_static/ |
| H A D | basic.css_t | 420 -moz-hyphens: manual; 421 -ms-hyphens: manual; 422 -webkit-hyphens: manual; 423 hyphens: manual;
|
| /f-stack/app/redis-5.0.5/deps/jemalloc/bin/ |
| H A D | jemalloc-config.in | 17 --mandir : Print manual page installation directory.
|
| /f-stack/freebsd/arm64/conf/ |
| H A D | GENERIC-UP | 4 # For more information on this file, please read the config(5) manual page,
|
| /f-stack/freebsd/arm/conf/ |
| H A D | COLIBRI-VF50 | 3 # For more information on this file, please read the config(5) manual page,
|
| H A D | QUARTZ | 3 # For more information on this file, please read the config(5) manual page,
|
| H A D | COSMIC | 3 # For more information on this file, please read the config(5) manual page,
|
| H A D | APALIS-IMX6 | 3 # For more information on this file, please read the config(5) manual page,
|
| H A D | SOCKIT | 4 # For more information on this file, please read the config(5) manual page,
|
| H A D | SOCDK | 4 # For more information on this file, please read the config(5) manual page,
|
| /f-stack/freebsd/contrib/device-tree/Bindings/eeprom/ |
| H A D | at24.yaml | 123 manual of your device, that value varies a lot. A wrong value 144 over reads to the next slave address. Please consult the manual of
|
| /f-stack/freebsd/contrib/openzfs/cmd/zed/zed.d/ |
| H A D | README | 26 https://www.gnu.org/software/autoconf/manual/autoconf.html#Portable-Shell
|