Home
last modified time | relevance | path

Searched refs:isn (Results 1 – 25 of 86) sorted by relevance

1234

/f-stack/freebsd/contrib/device-tree/Bindings/usb/
H A Dgeneric.txt7 "low-speed". In case this isn't passed via DT, USB
12 "peripheral" and "otg". In case this attribute isn't
18 In case this isn't passed via DT, USB controllers should
H A Ddwc3-st.txt37 is "otg", which isn't supported by this SoC. Valid dr_mode values for dwc3-st are either "host"
/f-stack/freebsd/contrib/ipfilter/netinet/
H A Dip_state.c865 isn = ips.ips_next;
866 if (isn == NULL) {
883 if (is == isn)
932 if (isn == NULL) {
937 bcopy((char *)&ips.ips_is, (char *)isn, sizeof(*isn));
942 isn->is_sti.tqe_parent = isn;
964 KFREE(isn);
991 isn->is_v);
1012 KFREE(isn);
1033 KFREE(isn);
[all …]
/f-stack/freebsd/mips/conf/
H A DTP-WN1043ND.hints14 # This isn't used, but configure it anyway.
38 # This isn't a lot of space!
82 # Don't flip on anything that isn't already enabled.
H A DWZR-HPAG300H.hints113 # Don't flip on anything that isn't already enabled.
114 # Force on CS lines for flash devices, apparently this isn't done
H A DROUTERSTATION.hints26 # Don't flip on anything that isn't already enabled.
H A DRSPRO.hints27 # Don't flip on anything that isn't already enabled.
H A DDIR-825B1.hints33 # The DIR-825B1 has an 8MB flash part - HOWEVER, the 64k caldata isn't
73 # Don't flip on anything that isn't already enabled.
H A DWZR-300HP.hints52 # The WRZ-300HP has 2 16MB flash part - HOWEVER, the 64k caldata isn't
148 # Don't flip on anything that isn't already enabled.
H A DAR933X_BASE.hints18 # NB: This isn't an ns8250 UART
H A DPB47.hints62 # Don't flip on anything that isn't already enabled by the
H A DAR934X_BASE.hints18 # NB: This isn't an ns8250 UART
H A DTL-ARCHERC7V2.hints201 # TODO: PCIe isn't showing link; maybe uboot isn't initialising
H A DQCA955X_BASE.hints21 # NB: This isn't an ns8250 UART
H A DTP-MR3020.hints86 # Don't flip on anything that isn't already enabled.
/f-stack/freebsd/contrib/device-tree/Bindings/serial/
H A Dqcom,msm-uart.txt4 dma-engine isn't needed. From a software perspective it's mostly compatible
/f-stack/freebsd/contrib/device-tree/Bindings/media/i2c/
H A Dmt9m111.txt19 0 if it isn't specified.
/f-stack/freebsd/contrib/device-tree/Bindings/net/
H A Dhisilicon-hns-dsaf.txt38 - phy-handle: phy handle of physical port. It is not required if there isn't
42 not required if there isn't cpld device.
/f-stack/freebsd/contrib/device-tree/src/arm/
H A Dkirkwood-ts219.dtsi110 * There is a s35390a available on the i2c bus, the internal rtc isn't
H A Drk3288-evb.dtsi166 * NOTE: vcc_sd isn't hooked up on v1.0 boards where power comes from
341 * Default drive strength isn't enough to achieve even
H A Dam335x-bonegreen-wireless.dts113 /* in case it isn't, wilink8 ends up in one of the test modes that */
/f-stack/freebsd/contrib/dev/ath/ath_hal/ar9300/
H A Deeprom.diff145 /* cal data in flash / DRAM isn't currently supported */
146 ath_hal_printf(ah, "%s: Cal data from DRAM isn't supported\n",
189 + ath_hal_printf(ah, "%s: FreeBSD: ah_cal_mem isn't set\n", __func__);
/f-stack/freebsd/contrib/device-tree/Bindings/virtio/
H A Diommu.txt24 - DMA from the IOMMU device isn't managed by another IOMMU. Therefore the
/f-stack/freebsd/contrib/openzfs/rpm/redhat/
H A Dzfs-kmod.spec.in48 echo "Kernel build directory isn't set properly, cannot continue"
/f-stack/freebsd/contrib/device-tree/Bindings/
H A DABI.rst24 binding because it isn't perfect.

1234