| /f-stack/freebsd/contrib/device-tree/src/arm64/freescale/ |
| H A D | fsl-ls1028a-kontron-kbox-a-230-ls.dts | 58 managed = "in-band-status"; 66 managed = "in-band-status"; 74 managed = "in-band-status"; 82 managed = "in-band-status";
|
| H A D | fsl-ls1028a-rdb.dts | 223 managed = "in-band-status"; 231 managed = "in-band-status"; 239 managed = "in-band-status"; 247 managed = "in-band-status";
|
| /f-stack/freebsd/contrib/device-tree/Bindings/net/wireless/ |
| H A D | brcm,bcm43xx-fmac.txt | 14 - interrupts : specifies attributes for the out-of-band interrupt (host-wake). 15 When not specified the device will use in-band SDIO interrupts. 16 - interrupt-names : name of the out-of-band interrupt, which must be set
|
| H A D | ieee80211.txt | 9 normally. It may happen chipset supports a wide wireless band but it is 11 An example case for this can be tri-band wireless router with two
|
| H A D | ti,wlcore.txt | 20 - interrupts : specifies attributes for the out-of-band interrupt.
|
| /f-stack/freebsd/contrib/device-tree/Bindings/net/ |
| H A D | btusb.txt | 23 that shall be used for out-of-band wake-on-bt. Driver will 26 platform out of band. During system resume, the irq will be 31 Following example uses irq pin number 3 of gpio0 for out of band wake-on-bt:
|
| /f-stack/freebsd/contrib/device-tree/src/arm64/marvell/ |
| H A D | armada-3720-turris-mox.dts | 155 managed = "in-band-status"; 381 managed = "in-band-status"; 388 managed = "in-band-status"; 398 managed = "in-band-status"; 465 managed = "in-band-status"; 572 managed = "in-band-status"; 580 managed = "in-band-status"; 590 managed = "in-band-status"; 657 managed = "in-band-status"; 764 managed = "in-band-status"; [all …]
|
| H A D | armada-8040-mcbin-singleshot.dts | 20 managed = "in-band-status"; 27 managed = "in-band-status";
|
| H A D | armada-3720-uDPU.dts | 167 managed = "in-band-status"; 175 managed = "in-band-status";
|
| H A D | armada-8040-clearfog-gt-8k.dts | 280 managed = "in-band-status"; 413 managed = "in-band-status"; 457 managed = "in-band-status";
|
| H A D | cn9131-db.dts | 92 managed = "in-band-status";
|
| /f-stack/freebsd/contrib/device-tree/src/arm/ |
| H A D | vf610-zii-scu4-aib.dts | 190 managed = "in-band-status"; 198 managed = "in-band-status"; 206 managed = "in-band-status"; 214 managed = "in-band-status"; 222 managed = "in-band-status"; 230 managed = "in-band-status"; 238 managed = "in-band-status"; 273 managed = "in-band-status"; 281 managed = "in-band-status"; 289 managed = "in-band-status";
|
| /f-stack/freebsd/net80211/ |
| H A D | ieee80211_scan.c | 542 nbands = (cie->len - 3) / sizeof(cie->band[0]); in dump_country() 544 schan = cie->band[i].schan; in dump_country() 545 nchan = cie->band[i].nchan; in dump_country() 548 cie->band[i].maxtxpwr); in dump_country() 550 printf(" %u,%u", schan, cie->band[i].maxtxpwr); in dump_country()
|
| /f-stack/freebsd/contrib/device-tree/Bindings/thermal/ |
| H A D | ti_soc_thermal.txt | 4 and a temperature sensor feature that are gathered in the band 5 gap voltage and temperature sensor (VBGAPTS) module. The band
|
| /f-stack/freebsd/contrib/device-tree/Bindings/ipmi/ |
| H A D | aspeed,ast2400-ibt-bmc.txt | 5 perform in-band IPMI communication with their host.
|
| H A D | npcm7xx-kcs-bmc.txt | 5 used to perform in-band IPMI communication with their host.
|
| H A D | aspeed-kcs-bmc.txt | 5 used to perform in-band IPMI communication with their host.
|
| /f-stack/freebsd/contrib/device-tree/Bindings/iio/frequency/ |
| H A D | adf4350.txt | 46 - adi,band-select-clock-mode-high-enable: Enables faster band
|
| /f-stack/freebsd/contrib/device-tree/Bindings/ata/ |
| H A D | qcom-sata.txt | 20 "rxoob" - RX out-of-band clock
|
| /f-stack/freebsd/mips/conf/ |
| H A D | TL-WDR4300 | 2 # TPLink TL-WDR4300 - AR9344 based dual-band 2x2 wifi
|
| /f-stack/freebsd/contrib/device-tree/Bindings/mtd/ |
| H A D | nand-controller.yaml | 77 it as the device ages. Otherwise, the out-of-band area of a 102 only the in-band area is used by the upper layers, and you
|
| /f-stack/freebsd/contrib/device-tree/Bindings/input/ |
| H A D | iqs269a.yaml | 136 azoteq,ati-band-disable: 138 description: Disables the ATI band check. 144 azoteq,ati-band-tighten: 146 description: Tightens the ATI band from 1/8 to 1/16 of the desired target.
|
| /f-stack/freebsd/contrib/device-tree/Bindings/serial/ |
| H A D | mtk-uart.txt | 30 support Rx in-band wake up. If one would like to use this feature,
|
| /f-stack/freebsd/contrib/device-tree/Bindings/display/ |
| H A D | ssd1307fb.txt | 13 - solomon,page-offset: Offset of pages (band of 8 pixels) that the screen is
|
| /f-stack/freebsd/contrib/device-tree/Bindings/hwmon/ |
| H A D | adi,ltc2947.yaml | 50 This property controls the Accumulation Dead band which allows to set the
|