| /f-stack/freebsd/contrib/device-tree/Bindings/rtc/ |
| H A D | rtc-fsl-ftm-alarm.txt | 4 - compatible : Should be "fsl,<chip>-ftm-alarm", the
6 "fsl,ls1012a-ftm-alarm"
7 "fsl,ls1021a-ftm-alarm"
8 "fsl,ls1028a-ftm-alarm"
9 "fsl,ls1043a-ftm-alarm"
10 "fsl,ls1046a-ftm-alarm"
11 "fsl,ls1088a-ftm-alarm"
12 "fsl,ls208xa-ftm-alarm"
13 "fsl,lx2160a-ftm-alarm"
32 compatible = "fsl,ls1088a-ftm-alarm";
|
| H A D | xlnx-rtc.txt | 4 Separate IRQ lines for seconds and alarm
11 - interrupt-names: interrupt line names eg. "sec" "alarm"
23 interrupt-names = "alarm", "sec";
|
| H A D | rtc-meson-vrtc.txt | 5 an alarm time (in seconds) is to be written.
9 - reg: physical address for the alarm register
11 The alarm register is a simple scratch register shared between the
|
| H A D | isil,isl12057.txt | 11 (associated with the alarm supported by the driver) is not connected
13 RTC alarm rings. In order to mark the device has a wakeup source and
29 Example isl12057 node without IRQ#2 pin connected (no alarm support):
68 PMIC, allowing the device to be started based on configured alarm:
|
| H A D | haoyu,hym8563.txt | 3 The HYM8563 provides basic rtc and alarm functionality
13 - interrupts: rtc alarm/event interrupt
|
| H A D | sa1100-rtc.txt | 7 - interrupts: Should be two. The first interrupt number is the rtc alarm
16 interrupt-names = "rtc 1Hz", "rtc alarm";
|
| H A D | microchip,pic32-rtc.txt | 5 configurable alarm.
11 - interrupts: RTC alarm/event interrupt
|
| H A D | rtc-m41t80.txt | 19 - interrupts: rtc alarm interrupt.
22 - wakeup-source: Enables wake up of host system on alarm
|
| H A D | cdns,rtc.txt | 3 The Cadence RTC controller with date, time and alarm capabilities.
4 The alarm may wake the system from low-power state.
|
| H A D | sa1100-rtc.yaml | 38 - const: 'rtc alarm'
54 interrupt-names = "rtc 1Hz", "rtc alarm";
|
| H A D | rtc-ds1307.txt | 26 - interrupts: rtc alarm interrupt.
29 - wakeup-source: Enables wake up of host system on alarm
|
| /f-stack/freebsd/contrib/device-tree/Bindings/thermal/ |
| H A D | qcom-spmi-temp-alarm.txt | 3 QPNP temperature alarm peripherals are found inside of Qualcomm PMIC chips
8 - compatible: Should contain "qcom,spmi-temp-alarm".
10 - interrupts: PMIC temperature alarm interrupt.
20 pm8941_temp: thermal-alarm@2400 {
21 compatible = "qcom,spmi-temp-alarm";
|
| /f-stack/freebsd/contrib/device-tree/Bindings/hwmon/ |
| H A D | gpio-fan.txt | 12 - alarm-gpios: This pin going active indicates something is wrong with
19 Note: At least one the "gpios" or "alarm-gpios" properties must be set.
30 alarm-gpios = <&gpio1 15 1>;
39 alarm-gpios = <&gpio2 15 1>;
|
| /f-stack/freebsd/contrib/device-tree/src/arm/ |
| H A D | kirkwood-linkstation-6282.dtsi | 32 pmx_led_alarm: pmx-led-alarm {
86 red-alarm-led {
87 label = "linkstation:red:alarm";
126 alarm-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
|
| H A D | qcom-pma8084.dtsi | 18 reg-names = "rtc", "alarm";
55 pma8084_temp: temp-alarm@2400 {
56 compatible = "qcom,spmi-temp-alarm";
|
| H A D | qcom-pm8841.dtsi | 24 temp-alarm@2400 {
25 compatible = "qcom,spmi-temp-alarm";
|
| H A D | kirkwood-nas2big.dts | 45 * An I2C fan controller (GMT G762) is used but alarm is
49 alarm-gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
93 * to power-up the board on an RTC alarm. The external RTC can
|
| H A D | kirkwood-lsxl.dtsi | 33 pmx_led_alarm: pmx-led-alarm {
142 alarm {
143 label = "lsxl:red:alarm";
174 alarm-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
|
| H A D | kirkwood-linkstation-duo-6281.dtsi | 28 pmx_led_alarm: pmx-led-alarm {
82 red-alarm-led {
83 label = "linkstation:red:alarm";
|
| H A D | at91-tse850-3.dts | 133 alarm-red {
134 label = "alarm:red";
137 alarm-green {
138 label = "alarm:green";
|
| /f-stack/freebsd/contrib/device-tree/src/arm64/qcom/ |
| H A D | pm8998.dtsi | 57 pm8998_temp: temp-alarm@2400 {
58 compatible = "qcom,spmi-temp-alarm";
90 reg-names = "rtc", "alarm";
|
| H A D | pm8150.dtsi | 64 pm8150_temp: temp-alarm@2400 {
65 compatible = "qcom,spmi-temp-alarm";
103 reg-names = "rtc", "alarm";
|
| H A D | pms405.dtsi | 74 pms405_temp: temp-alarm@2400 {
75 compatible = "qcom,spmi-temp-alarm";
136 reg-names = "rtc", "alarm";
|
| H A D | pm8916.dtsi | 18 reg-names = "rtc", "alarm";
65 pm8916_temp: temp-alarm@2400 {
66 compatible = "qcom,spmi-temp-alarm";
|
| /f-stack/dpdk/lib/librte_eal/common/ |
| H A D | eal_common_trace_points.c | 45 lib.eal.alarm.set)
47 lib.eal.alarm.cancel)
|