Changes in Makefile

638ab30c - arm64: dts: ti: am64-phyboard-electra: Add DT overlay for X27 connector

Tue, 28 Jan 2025 10:03:56 +0000

arm64: dts: ti: am64-phyboard-electra: Add DT overlay for X27 connectorAdd a device tree overlay for SPI1 , UART3 and GPIO1 onX27 connector.By default, not all interfaces on the X27 connector are accessibledue to being disabled or set to alternative pin mux configurations.This overlay activates and configures these interfaces to supportconnections with external devices.Signed-off-by: Wadim Egorov Signed-off-by: Daniel Schultz Link: https://lore.kernel.org/r/20250128100356.462934-1-d.schultz@phytec.deSigned-off-by: Vignesh Raghavendra List of files: /linux-6.15/scripts/dtc/include-prefixes/arm64/ti/Makefile

e2b69180 - arm64: dts: ti: k3-am642-hummingboard-t: Convert overlay to board dts

Wed, 01 Jan 2025 12:30:22 +0000

arm64: dts: ti: k3-am642-hummingboard-t: Convert overlay to board dtsSolidRun HummingBoard-T has two options for M.2 connector, supportingeither PCI-E or USB-3.1 Gen 1 - depending on configuration of a muxon the serdes lane.The required configurations in device-tree were modeled as overlays.The USB-3.1 overlay uses /delete-property/ to unset a boolean propertyon the usb controller limiting it to USB-2.0 by default.Overlays can not delete a property from the base dtb, therefore thisoverlay is at this time useless.Convert both overlays into full dts by including the base board dts.While the pcie overlay was functional, both are converted for aconsistent user experience when selecting between the two mutuallyexclusive configurations.Reported-by: Geert Uytterhoeven Closes: https://lore.kernel.org/linux-devicetree/CAMuHMdXTgpTnJ9U7egC2XjFXXNZ5uiY1O+WxNd6LPJW5Rs5KTw@mail.gmail.comFixes: bbef42084cc1 ("arm64: dts: ti: hummingboard-t: add overlays for m.2 pci-e and usb-3")Signed-off-by: Josua Mayer Link: https://lore.kernel.org/r/20250101-am64-hb-fix-overlay-v2-1-78143f5da28c@solid-run.comSigned-off-by: Nishanth Menon List of files: /linux-6.15/scripts/dtc/include-prefixes/arm64/ti/Makefile

b09cc758 - arm64: dts: ti: k3-am69-sk: Add overlay for PCIE0 Endpoint Mode

Thu, 05 Dec 2024 10:50:36 +0000

arm64: dts: ti: k3-am69-sk: Add overlay for PCIE0 Endpoint ModeAdd overlay to enable the PCIE0 instance of PCIe on AM69-SK in Endpointmode of operation.Signed-off-by: Siddharth Vadapalli Link: https://lore.kernel.org/r/20241205105041.749576-5-s-vadapalli@ti.comSigned-off-by: Nishanth Menon List of files: /linux-6.15/scripts/dtc/include-prefixes/arm64/ti/Makefile

58efed58 - arm64: dts: ti: k3-am68-sk-base-board: Add overlay for PCIE1 Endpoint Mode

Thu, 05 Dec 2024 10:50:35 +0000

arm64: dts: ti: k3-am68-sk-base-board: Add overlay for PCIE1 Endpoint ModeAdd overlay to enable the PCIE1 instance of PCIe on AM68-SK-Base-Board inEndpoint mode of operation. PCIE1 on AM68-SK-Base-Board supports x2 Laneoperation unlike its counterpart on J721S2-EVM which supports x1 Lane.Signed-off-by: Siddharth Vadapalli Link: https://lore.kernel.org/r/20241205105041.749576-4-s-vadapalli@ti.comSigned-off-by: Nishanth Menon List of files: /linux-6.15/scripts/dtc/include-prefixes/arm64/ti/Makefile

c3015d45 - arm64: dts: ti: k3-j721e-evm: Add overlay for PCIE1 Endpoint Mode

Thu, 05 Dec 2024 10:50:34 +0000

arm64: dts: ti: k3-j721e-evm: Add overlay for PCIE1 Endpoint ModeAdd overlay to enable the PCIE1 instance of PCIe on J721E-EVM in Endpointmode of operation. Additionally, in order to support both PCIE0 and PCIE1in Endpoint Mode of operation, enable applying device-tree overlays on"k3-j721e-evm-pcie0-ep.dtb", thereby allowing the overlay for PCIE1 inEndpoint mode to be applied on the aforementioned DTB.Signed-off-by: Siddharth Vadapalli Link: https://lore.kernel.org/r/20241205105041.749576-3-s-vadapalli@ti.comSigned-off-by: Nishanth Menon List of files: /linux-6.15/scripts/dtc/include-prefixes/arm64/ti/Makefile

a7543eae - arm64: dts: ti: Makefile: Fix typo "k3-j7200-evm-pcie1-ep.dtbo"

Thu, 05 Dec 2024 10:50:33 +0000

arm64: dts: ti: Makefile: Fix typo "k3-j7200-evm-pcie1-ep.dtbo"The list of "dtbs" should contain the resultant "dtb" formed by applyingthe "dtbo" overlay on the base "dtb", rather than the "dtbo" itself.Hence, change "k3-j7200-evm-pcie1-ep.dtbo" to "k3-j7200-evm-pcie1-ep.dtb"in the list of "dtbs".Fixes: f43ec89bbc83 ("arm64: dts: ti: k3-j7200-evm: Add overlay for PCIE1 Endpoint Mode")Signed-off-by: Siddharth Vadapalli Link: https://lore.kernel.org/r/20241205105041.749576-2-s-vadapalli@ti.comSigned-off-by: Nishanth Menon List of files: /linux-6.15/scripts/dtc/include-prefixes/arm64/ti/Makefile

881f5e9d - arm64: dts: ti: k3-am62-verdin: Add Ivy carrier board

Tue, 24 Sep 2024 12:00:44 +0000

arm64: dts: ti: k3-am62-verdin: Add Ivy carrier boardAdd Toradex Verdin Ivy carrier board support. One notable feature of Ivyis the analog inputs. These inputs are multiplexed, allowing the sameinput to measure either voltage or current. For current measurements,a GPIO switch enables or disables the shunt resistor. This process isautomatically managed by the Linux kernel using the IIO and MUXsubsystems. Voltage measurement is always enabled, but the voltagemeasured by the ADC is scaled by a cascade voltage divider. In thedevice tree, the equivalent gain of the voltage divider is used, whichcan be calculated as follows: ------------ + | .-. R1=30K | | | | '-' |-------------------Analog Input (AIN) | | .-. .-. R2=10K | | R3=30K | | | | | | '-' '-' | | | |-------- | .-. + | R4=10K | | | | | ADC Input (Channels 0 and 1) | '-' - | | - -----------| |-------- === === GND GNDVin = Analog Input (AIN)Vout = ADC InputRth = Thevenin Equiv. ResistanceVth = Thevenin Equiv. VoltageRL = Load ResistorR1 = 30K, R2 = 10K, R3 = 30K, R4 = 10KRL = R4 = 10KRth = (R1 // R2) + R3 = 37500 OhmsVth = (Vin * R2) / (R1 + R2) = Vin/4;Vout = (Vth * RL)/ (Rth + RL) = Vth/4.75 = Vin/19Gain = Vout/Vin = 1/19https://www.toradex.com/products/carrier-board/ivy-carrier-boardSigned-off-by: João Paulo Gonçalves Signed-off-by: Francesco Dolcini Link: https://lore.kernel.org/r/20240924120044.130913-4-francesco@dolcini.itSigned-off-by: Vignesh Raghavendra List of files: /linux-6.15/scripts/dtc/include-prefixes/arm64/ti/Makefile

34d7b841 - arm64: dts: ti: k3-am642-evm: Add overlay for PCIe0 EP mode

Mon, 30 Sep 2024 10:34:13 +0000

arm64: dts: ti: k3-am642-evm: Add overlay for PCIe0 EP modeAdd overlay to enable the PCIe0 instance of PCIe on AM642-EVM inEndpoint mode of operation.Signed-off-by: Siddharth Vadapalli Link: https://lore.kernel.org/r/20240930103413.3085689-1-s-vadapalli@ti.comSigned-off-by: Vignesh Raghavendra List of files: /linux-6.15/scripts/dtc/include-prefixes/arm64/ti/Makefile

f43ec89b - arm64: dts: ti: k3-j7200-evm: Add overlay for PCIE1 Endpoint Mode

Tue, 01 Oct 2024 09:34:26 +0000

arm64: dts: ti: k3-j7200-evm: Add overlay for PCIE1 Endpoint ModeAdd overlay to enable the PCIE1 instance of PCIe on J7200-EVM inEndpoint mode of operation.Signed-off-by: Siddharth Vadapalli Link: https://lore.kernel.org/r/20241001093426.3401765-1-s-vadapalli@ti.comSigned-off-by: Vignesh Raghavendra List of files: /linux-6.15/scripts/dtc/include-prefixes/arm64/ti/Makefile

151ed40a - Revert "arm64: dts: ti: am62-phyboard-lyra: Add overlay to increase cpu frequency to 1.4 GHz"

Tue, 01 Oct 2024 07:19:16 +0000

Revert "arm64: dts: ti: am62-phyboard-lyra: Add overlay to increase cpu frequency to 1.4 GHz"We now configure the a53_opp_table to include a 1.4 GHz node and set ourVDD_CORE to 0.85v in the k3-am62-phycore-som.dtsi. This change is tomatch our PMIC which is now set to output 0.85v by default.This reverts commit 7a5775a3da906dab059b8de60a2b88f6016cb4b8.Signed-off-by: Garrett Giordano Link: https://lore.kernel.org/r/20241001071916.1362213-3-ggiordano@phytec.comSigned-off-by: Vignesh Raghavendra List of files: /linux-6.15/scripts/dtc/include-prefixes/arm64/ti/Makefile

13dc96a5 - arm64: dts: ti: Add support for J742S2 EVM board

Mon, 02 Sep 2024 12:26:53 +0000

arm64: dts: ti: Add support for J742S2 EVM boardJ742S2 EVM board is designed for TI J742S2 SoC. It supports the followinginterfaces:* 16 GB DDR4 RAM* x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode* x1 Input Audio Jack, x1 Output Audio Jack* x1 USB2.0 Hub with two Type A host and x1 USB 3.1 Type-C Port* x1 4L PCIe connector* x1 UHS-1 capable micro-SD card slot* 512 Mbit OSPI flash, 1 Gbit Octal NAND flash, 512 Mbit QSPI flash, UFS flash.* x6 UART through UART-USB bridge* XDS110 for onboard JTAG debug using USB* Temperature sensors, user push buttons and LEDs* x1 GESI expander, x2 Display connector* x1 15-pin CSI header* x6 MCAN instancesLink: https://www.ti.com/lit/ug/sprujd8/sprujd8.pdf (EVM user guide)Link: https://www.ti.com/lit/zip/SPAC001 (Schematics)Reviewed-by: Beleswar Padhi Signed-off-by: Manorit Chawdhry Link: https://lore.kernel.org/r/20240902-b4-upstream-j742s2-v6-5-6a7aa2736797@ti.comSigned-off-by: Vignesh Raghavendra List of files: /linux-6.15/scripts/dtc/include-prefixes/arm64/ti/Makefile

c5e61596 - arm64: dts: ti: Add k3-am67a-beagley-ai

Thu, 29 Aug 2024 21:39:29 +0000

arm64: dts: ti: Add k3-am67a-beagley-aiBeagleBoard.org BeagleY-AI is an easy to use, affordable open sourcehardware single board computer based on the Texas Instruments AM67A,which features a quad-core 64-bit Arm CPU subsystem, 2 general-purposedigital-signal-processors (DSP) and matrix-multiply-accelerators (MMA),GPU, vision and deep learning accelerators, and multiple Arm Cortex-R5cores for low-power, low-latency GPIO control.https://beagley-ai.org/https://openbeagle.org/beagley-ai/beagley-aiSigned-off-by: Robert Nelson Reviewed-by: Roger Quadros Reviewed-by: Jared McArthur Link: https://lore.kernel.org/r/20240829213929.48540-2-robertcnelson@gmail.comSigned-off-by: Nishanth Menon List of files: /linux-6.15/scripts/dtc/include-prefixes/arm64/ti/Makefile

dba27d02 - arm64: dts: ti: iot2050: Add overlays for M.2 used by firmware

Wed, 28 Aug 2024 07:39:01 +0000

arm64: dts: ti: iot2050: Add overlays for M.2 used by firmwareTo allow firmware to pick up all DTs from here, move the overlays thatare normally applied during DT fixup to the kernel source as well. Hookthen into the build nevertheless to ensure that regular checks areperformed.Signed-off-by: Jan Kiszka Link: https://lore.kernel.org/r/91f8b825467651ebd51a4051f153ab136eeb1849.1724830741.git.jan.kiszka@siemens.comSigned-off-by: Nishanth Menon List of files: /linux-6.15/scripts/dtc/include-prefixes/arm64/ti/Makefile

d6938388 - arm64: dts: ti: Add basic support for phyBOARD-Lyra-AM62Ax

Wed, 26 Jun 2024 15:52:44 +0000

arm64: dts: ti: Add basic support for phyBOARD-Lyra-AM62AxThe phyCORE-AM62Ax [1] is a SoM (System on Module) featuring TI's AM62Ax SoC.It can be used in combination with different carrier boards.This module can come with different sizes and models forDDR, eMMC, SPI NOR Flash and various SoCs from the AM62Ax family.A development Kit, called phyBOARD-Lyra [2] is used as a carrier boardreference design with a mapper board being used to allow the phyCORE-AM62Axto fit the phyBOARD-Lyra.Supported features: * Debug UART * SPI NOR Flash * eMMC * 2x Ethernet * Micro SD card * I2C EEPROM * I2C RTC * GPIO Expander * LEDs * USB * HDMI * USB-C * AudioFor more details, see:[1] Product page SoM: https://www.phytec.com/product/phycore-am62a[2] Product page CB: https://www.phytec.com/product/phyboard-am62aSigned-off-by: Garrett Giordano Reviewed-by: Wadim Egorov Link: https://lore.kernel.org/r/20240626155244.3311436-4-ggiordano@phytec.comSigned-off-by: Vignesh Raghavendra List of files: /linux-6.15/scripts/dtc/include-prefixes/arm64/ti/Makefile

e5691522 - arm64: dts: ti: am62-lp-sk: Add overlay for NAND expansion card

Sat, 22 Jun 2024 11:59:57 +0000

arm64: dts: ti: am62-lp-sk: Add overlay for NAND expansion cardThe NAND expansion card (PROC143E1) connects over the User/MCU/PRUExpansion port on the am62-lp-sk EVM.The following pins are shared between McASP1 and GPMC-NAND soboth cannot work simultaneously.Pin name McASP1 function GPMC function======== =============== =============J17 MCASP1_AXR0 GPMC0_WENP21 MCASP1_AFSX GPMC0_WAIT0K17 MCASP1_ACLKX GPMC0_BE0N_CLEK20 MCASP1_AXR2 GPMC0_ADVN_ALEThe factory default sets the pins for McASP1 use. (i.e.Resistor Array RA1 installed, RA4 not installed).For NAND use, RA1 has to be removed and RA4 must beinstalled.Signed-off-by: Roger Quadros Link: https://lore.kernel.org/r/20240622-am62lp-sk-nand-v1-2-caee496eaf42@kernel.orgSigned-off-by: Vignesh Raghavendra List of files: /linux-6.15/scripts/dtc/include-prefixes/arm64/ti/Makefile

45a792b5 - arm64: dts: ti: k3-am6xx-phycore-qspi-nor: Add overlay to enable QSPI NOR

Fri, 21 Jun 2024 23:31:43 +0000

arm64: dts: ti: k3-am6xx-phycore-qspi-nor: Add overlay to enable QSPI NORAdd an overlay to change from the default OSPI NOR to QSPI NORfor all am6xx-phycore-som boards.The EEPROM on am6xx-phycore-soms contains information about theconfiguration of the SOM. The standard configuration of the SOMhas an ospi nor, but if qspi nor is populated, the EEPROM willindicate that change and we can use this overlay to cleanly change toqspi nor.Signed-off-by: Nathan Morrisson Link: https://lore.kernel.org/r/20240621233143.2077941-1-nmorrisson@phytec.comSigned-off-by: Vignesh Raghavendra List of files: /linux-6.15/scripts/dtc/include-prefixes/arm64/ti/Makefile

117937ff - arm64: dts: ti: am642-evm: Add overlay for NAND expansion card

Fri, 14 Jun 2024 15:06:42 +0000

arm64: dts: ti: am642-evm: Add overlay for NAND expansion cardThe NAND expansion card plugs in over the HSE (High Speed Expansion)connector. Add support for it.We add the ranges property to the GPMC node instead of the NANDoverlay file to prevent below warnings./fragment@3/__overlay__: Relying on default #address-cells value/fragment@3/__overlay__: Relying on default #size-cells valueAs GPMC is dedicated for NAND use on this board, it should be OK.Signed-off-by: Roger Quadros Link: https://lore.kernel.org/r/20240614-am642-evm-nand-v5-1-acf760896239@kernel.orgSigned-off-by: Vignesh Raghavendra List of files: /linux-6.15/scripts/dtc/include-prefixes/arm64/ti/Makefile

9a323788 - arm64: dts: ti: k3-am6xx-phycore-som: Add overlay to disable spi nor

Thu, 13 Jun 2024 23:07:59 +0000

arm64: dts: ti: k3-am6xx-phycore-som: Add overlay to disable spi norAdd an overlay to disable the spi nor for all am6xx-phycore-somboards.The EEPROM on am6xx-phycore-soms contains information about theconfiguration of the SOM. The standard configuration of the SOMhas an ospi nor, but if no nor is populated, the EEPROM will indicatethat change and we can use this overlay to cleanly disable thespi nor.Signed-off-by: Nathan Morrisson Link: https://lore.kernel.org/r/20240613230759.1984966-5-nmorrisson@phytec.comSigned-off-by: Vignesh Raghavendra List of files: /linux-6.15/scripts/dtc/include-prefixes/arm64/ti/Makefile

a0b55260 - arm64: dts: ti: k3-am6xx-phycore-som: Add overlay to disable rtc

Thu, 13 Jun 2024 23:07:58 +0000

arm64: dts: ti: k3-am6xx-phycore-som: Add overlay to disable rtcAdd an overlay to disable the rtc for all am6xx-phycore-som boards.The EEPROM on am6xx-phycore-soms contains information about theconfiguration of the SOM. The standard configuration of the SOMhas an rtc, but if no rtc is populated, the EEPROM will indicate thatchange and we can use this overlay to cleanly disable the rtc.Signed-off-by: Nathan Morrisson Link: https://lore.kernel.org/r/20240613230759.1984966-4-nmorrisson@phytec.comSigned-off-by: Vignesh Raghavendra List of files: /linux-6.15/scripts/dtc/include-prefixes/arm64/ti/Makefile

1322b179 - arm64: dts: ti: k3-am6xx-phycore-som: Add overlay to disable eth phy

Thu, 13 Jun 2024 23:07:57 +0000

arm64: dts: ti: k3-am6xx-phycore-som: Add overlay to disable eth phyAdd an overlay to disable the eth phy for all am6xx-phycore-somboards.The EEPROM on am6xx-phycore-soms contains information about theconfiguration of the SOM. The standard configuration of the SOMhas an ethernet phy, but if no ethernet phy is populated, the EEPROMwill indicate that change and we can use this overlay to cleanlydisable the ethernet phy.Signed-off-by: Nathan Morrisson Link: https://lore.kernel.org/r/20240613230759.1984966-3-nmorrisson@phytec.comSigned-off-by: Vignesh Raghavendra List of files: /linux-6.15/scripts/dtc/include-prefixes/arm64/ti/Makefile