Changes in Makefile

ec8f24b7 - treewide: Add SPDX license identifier - Makefile/Kconfig

Sun, 19 May 2019 12:07:45 +0000

treewide: Add SPDX license identifier - Makefile/KconfigAdd SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any formThese files fall under the project license, GPL v2 only. The resulting SPDXlicense identifier is: GPL-2.0-onlySigned-off-by: Thomas Gleixner Signed-off-by: Greg Kroah-Hartman List of files: /linux-6.15/drivers/net/ethernet/brocade/bna/Makefile

9d92dafe - bna: remove obsolete use of EXTRA_CFLAGS

Tue, 09 Jun 2015 12:24:43 +0000

bna: remove obsolete use of EXTRA_CFLAGSEXTRA_CFLAGS should be used on the command line only.Since EXTRA_CFLAGS here add only a non-existant path to compilerinclude paths (by -I), remove EXTRA_CFLAGS completely.Signed-off-by: Jiri Slaby Signed-off-by: David S. Miller List of files: /linux-6.15/drivers/net/ethernet/brocade/bna/Makefile

2732ba56 - bna: QLogic BR-series Adapters Driver Rebranding

Thu, 19 Feb 2015 21:02:31 +0000

bna: QLogic BR-series Adapters Driver RebrandingRe-brand the BNA driver to QLogic.Signed-off-by: Rasesh Mody Signed-off-by: David S. Miller List of files: /linux-6.15/drivers/net/ethernet/brocade/bna/Makefile

7afc5dbd - bna: Add debugfs interface.

Thu, 22 Dec 2011 13:30:19 +0000

bna: Add debugfs interface.Change details: - Add debugfs support to obtain firmware trace, saved firmware trace on an IOC crash, driver info and read/write to registers. - debugfs hierarchy: bna/pci_dev: where the pci_name corresponds to the one under /sys/bus/pci/drivers/bna - Following are the new debugfs entries added: fwtrc: collect current firmware trace. fwsave: collect last saved fw trace as a result of firmware crash. regwr: write one word to chip register regrd: read one or more words from chip register. drvinfo: collect the driver information.Signed-off-by: Krishna Gudipati Signed-off-by: David S. Miller List of files: /linux-6.15/drivers/net/ethernet/brocade/bna/Makefile

078086f3 - bna: ENET and Tx Rx Redesign Enablement

Mon, 08 Aug 2011 16:21:39 +0000

bna: ENET and Tx Rx Redesign EnablementChange details:This patch contains additional structure and function definition changesthat are required to enable the new msgq/enet/txrx redesign introducedby the previous 4 patches. - structure and function definition changes to header files as a result of Ethport, Enet, IOCEth, Tx, Rx redesign. - ethtool changes to use new enet function and definitions - Set number of Tx and Rx queues bassed on underlying hardware. Define separate macros for maximum and supported numbers of Tx and Rx queues based on underlying hardware. Take VLAN header into account for MTU calculation. Default to INTx mode when pci_enable_msix() fails. Set a bit in Rx poll routine, check and wait for that bit to be cleared in the cleanup routine before proceeding. - The TX and Rx coalesce settings are programmed in steps of 5 us. The value that are not divisible by 5 are rounded to the next lower number. This was causing the value os 1 to 4 to be rounded to 0, which is an invalid setting. When creating Rx and Tx object, we are currently assigning the default values of Rx and Tx coalescing_timeo. If these values are changed in the driver to a different value, the change is lost during such operations as MTU change. In order to avoid that, pass the configured value of coalescing_timeo before Rx and Tx object creation. Fix bnad_tx_coalescing_timeo_set() so it applies to all the Tx objects. - Reorg uninitialization path in case of pci_probe failure. - Hardware clock setup changes to pass asic generation, port modes and asic mode as part firmware boot parameters to firmware. - FW mailbox interface changes to defined asic specific mailbox interfaces. h/w mailbox interfaces take 8-bit FIDs and 2-bit port id for owner. Cleaned up mailbox definitions and usage for new and old HW. Eliminated usage of ASIC ID. MSI-X vector assignment and programming done by firmware. Fixed host offsets for CPE/RME queue registers. - Implement polling mechanism for FW ready to have poll mechanism replaces the current interrupt based FW READY method. The timer based poll routine in IOC will query the ioc_fwstate register to see if there is a state change in FW, and sends the READY event. Removed infrastructure needed to support mbox READY event from fw as well as IOC code. - Move FW init to HW init. Handle the case where PCI mapping goes away when IOCPF state machine is waiting for semaphore. - Add IOC mbox call back to client indicating that the command is sent.Signed-off-by: Rasesh Mody Signed-off-by: David S. Miller List of files: /linux-6.15/drivers/net/ethernet/brocade/bna/Makefile

af027a34 - bna: MSGQ Implementation

Mon, 08 Aug 2011 16:21:35 +0000

bna: MSGQ ImplementationChange details: - Currently modules communicate with the FW using 32 byte command and response register. This limits the size of the command and response messages exchanged with the FW to 32 bytes. We need a mechanism to exchange the comamnds and responses exchange with FW that exceeds 32 bytes. - MSGQ implementation provides that facility. It removes the assumption that command/response queue size is precisely calculated to accommodate all concurrent FW commands/responses. The queue depth is made variable now, defined by a macro. A waiting command list is implemented to hold all the commands when there is no place in the command queue. Callback is implemented for each command entry to invoke the module posting the command, when there is space in the command queue and the command was finally posted to the queue. Module/Object information is embedded in the response for tracking purpose.Signed-off-by: Rasesh Mody Signed-off-by: David S. Miller List of files: /linux-6.15/drivers/net/ethernet/brocade/bna/Makefile

f844a0ea - bna: Move the Brocade driver

Fri, 13 May 2011 08:00:03 +0000

bna: Move the Brocade driverMoves the Brocade driver into drivers/net/ethernet/brocade/ and makethe necessary Kconfig and Makefile changes.CC: Rasesh Mody CC: Debashis Dutt Signed-off-by: Jeff Kirsher List of files: /linux-6.15/drivers/net/ethernet/brocade/bna/Makefile