Lines Matching refs:value
144 the server. In all such cases, the actual value sent may either be
146 value), or a number of seconds starting from current time. In the
149 that, the server will consider it to be real Unix time value rather
248 server time). If a negative value is given the item is immediately
255 - <cas unique> is a unique 64-bit value of an existing entry.
256 Clients should use the value returned from the "gets" command
313 - <flags> is the flags value set by the storage command
360 the current data value does not conform to such a representation, the
362 bogus value as if it were 0, leading to confusion). Also, the item
364 that a non-existent key exists with value 0; instead, they will fail.
368 incr <key> <value> [noreply]\r\n
372 decr <key> <value> [noreply]\r\n
376 - <value> is the amount by which the client wants to increase/decrease
385 - "NOT_FOUND\r\n" to indicate the item with this value was not found
387 - <value>\r\n , where <value> is the new value of the item's data,
391 to decrease the value below 0, the new value will be 0. Overflow in
453 - <flags> is the flags value set by the storage command
467 metadata of an item, minus the value.
472 - if <flag> is 'b', then <key> is a base64 encoded binary value. the response
530 If the request did not ask for a value in the response (v) flag, the server
543 - b: interpret key as base64 encoded binary value
549 - O(token): opaque value, consumes a token and copies back with response
554 - v: return item value in <data block>
557 - E(token): use token as new CAS value if item is modified
569 - b: interpret key as base64 encoded binary value
581 The above two flags return the value of "hit before?" and "last access time"
585 - O(token): opaque value, consumes a token and copies back with response
617 - v: return item value in <data block>
623 - E(token): use token as new CAS value if item is modified
625 Normally when an item is created it is given a CAS value from an internal
627 unsigned integer) with the specified value. This is useful for using an
729 - b: interpret key as base64 encoded binary value (see metaget)
730 - c: return CAS value if successfully stored.
731 - C(token): compare CAS value when storing item
732 - E(token): use token as new CAS value (see metaget for detail)
736 - O(token): opaque value, consumes a token and copies back with response
745 - c: returns the CAS value on successful storage. Will return 0 on error, but
746 clients must not depend on the return value being zero. In future versions
747 this may return the current CAS value for "EX" return code conditions.
749 - C(token): compare CAS value when storing item
752 matches the current CAS value of the item. When combined with the 'I' flag, a
753 CAS value that is _lower_ than the current value may be accepted, but the item
764 - O(token): opaque value, consumes a token and copies back with response
781 A: "append" command. If item exists, append the new value to its data.
782 P: "prepend" command. If item exists, prepend the new value to its data.
786 The "cas" command is supplanted by specifying the cas value with the 'C' flag.
787 Append and Prepend modes will also respect a supplied cas value.
825 - b: interpret key as base64 encoded binary value (see metaget)
826 - C(token): compare CAS value
827 - E(token): use token as new CAS value (see metaget for detail)
833 - x: removes the item value, but leaves the item.
837 - C(token): compare CAS value
839 Can be used to only delete or mark-stale if a supplied CAS value matches.
843 Instead of removing an item, this will give the item a new CAS value and mark
862 - x: removes the item value, but leaves the item.
864 This deletes the value off of an item (by replacing it with an empty value
866 tombstone of a previous value.
906 - b: interpret key as base64 encoded binary value (see metaget)
907 - C(token): compare CAS value (see mset)
908 - E(token): use token as new CAS value (see metaget for detail)
910 - J(token): initial value to use if auto created after miss (default 0)
914 - O(token): opaque value, consumes a token and copies back with response
917 - c: return current CAS value if successful.
918 - v: return new value
923 - C(token): compare CAS value
925 Can be used to only incr/decr if a supplied CAS value matches. A new CAS value
927 value after success.
931 Similar to mget, on a miss automatically create the item. A value can be
934 - J(token): initial value
936 An unsigned 64-bit integer which will be seeded as the value on a miss. Must be
946 On success, sets the remaining TTL to the supplied value.
1097 A value of "0" disables the sleep, "1000000" (one second) is the max.
1147 Lines are in "key=value key2=value2" format, with value being URI encoded
1216 The response format is in "key=value key2=value2" format, for easy parsing.
1222 The value of keys (and potentially other things) are "URI encoded". Since most
1284 STAT <name> <value>\r\n
1291 <value> is the data. The following is the list of all names sent in
1292 response to the "stats" command, together with the type of the value
1293 sent for this name, and the meaning of the value.
1361 | | | found, but the CAS value did not match. |
1367 | | | caused by attempting to write a value |
1480 | chunk_size | 32 | Minimum space allocated for key+value+flags. |
1542 STAT items:<slabclass>:<stat> <value>\r\n
1675 STAT <slabclass>:<stat> <value>\r\n
1676 STAT <stat> <value>\r\n
1699 | | value due to a bad CAS id. |
1716 STAT <file descriptor>:<stat> <value>\r\n
1742 The value of the "state" stat may be one of the following:
1901 monotonically increasing value starting from a random seed, but the client